DOI QR코드

DOI QR Code

Component deformation-based seismic design method for RC structure and engineering application

  • Han, Xiaolei (School of Civil and Transportation Engineering, South China University of Technology) ;
  • Huang, Difang (School of Civil and Transportation Engineering, South China University of Technology) ;
  • Ji, Jing (School of Civil and Transportation Engineering, South China University of Technology) ;
  • Lin, Jinyue (School of Civil and Transportation Engineering, South China University of Technology)
  • 투고 : 2018.11.15
  • 심사 : 2019.03.28
  • 발행 : 2019.05.25

초록

Seismic design method based on bearing capacity has been widely adopted in building codes around the world, however, damage and collapse state of structure under strong earthquake can not be reflected accurately. This paper aims to present a deformation-based seismic design method based on the research of RC component deformation index limit, which combines with the feature of Chinese building codes. In the proposed method, building performance is divided into five levels and components are classified into three types according to their importance. Five specific design approaches, namely, "Elastic Design", "Unyielding Design", "Limit Design", "Minimum Section Design" and "Deformation Assessment", are defined and used in different scenarios to prove whether the seismic performance objectives are attained. For the components which exhibit ductile failure, deformation of components under strong earthquake are obtained quantitatively in order to identify the damage state of the components. For the components which present brittle shear failure, their performance is guaranteed by bearing capacity. As a case study, seismic design of an extremely irregular twin-tower high rise building was carried out according to the proposed method. The results evidenced that the damage and anti-collapse ability of structure were estimated and controlled by both deformation and bearing capacity.

키워드

과제정보

연구 과제 주관 기관 : Natural Science Foundation of Guangdong Province, NSFC (National Natural Science Foundation of China)

참고문헌

  1. Acun, B. and Sucuoglu, H. (2010), "Performance of reinforced concrete columns designed for flexure under severe displacement cycles", ACI Struct. J., 107, 364-371.
  2. ASCE/SEI 31 (2003), Seismic Evaluation of Existing Buildings, American Society of Civil Engineers, Reston, Virginia, USA.
  3. ASCE/SEI 41 (2006), Seismic Rehabilitation of Existing Buildings, American Society of Civil Engineers, Reston, Virginia, USA.
  4. ASCE/SEI 7 (2016), Minimum Design Loads for Buildings and Other Structures, American Society of Civil Engineers: Reston, Virginia, USA.
  5. ATC-40 (1996), Seismic Evaluation and Retrofit of Concrete Buildings. Applied Technology Council, Redwood, California, USA.
  6. CTBUH (2008), Recommendations for the Seismic Design of High-rise Buildings, Council on Tall Buildings and Urban Habitat, Illinois Institute of Technology, Chicago, USA.
  7. Cui, J.D. (2017), "Research and experimental verification of deformation index limits of RC beams, columns and shear walls", Ph.D. Dissertation, South China University of Technology, Guangzhou, China.
  8. Cui, J.D., Han, X.L., Gong, H.J. and Ji, J. (2018b), "Deformation limits of reinforces concrete columns and their experimental verification", J. Tongji Univ. (Nat. Sci.), 46(5), 593-603.
  9. Cui, J.D., Han, X.L., Ji, J. and Gong, H.J. (2018a), "Experimental study on deformation limits of RC beams", J. Harbin Inst. Technol., 50(6), 169-176.
  10. Elif, M.U., Erberik, M.A. and Askan, A. (2015), "Performance assessment of Turkish residential buildings for seismic damage and loss estimation", J. Perform. Constr. Facil., 29(2), 04014063. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000547.
  11. Elwood, K.J. and Moehle, J.P. (2006) "Idealized backbone model for existing reinforced concrete columns and comparisons with FEMA 356 criteria", Struct. Des. Tall Spec. Build., 15, 553-569. https://doi.org/10.1002/tal.382.
  12. Elwood, K.J., Matamoros, A., Wallace, J.W., Lehman, D., Heintz, L., Mitchell, A., Moore, M., Valley, M., Lowes, L.N., Comartin, C. and Moehle, J.P. (2007) "Update to ASCE/SEI 41 concrete provisions", Earthq. Spectra, 23(3), 493. https://doi.org/10.1193/1.2757714.
  13. ETABS (2016), Extended 3D Analysis of Building Systems Software, Computers and Structures, Inc., Berkeley, CA, USA.
  14. FEMA 273 (1997), NEHRP Guidelines for Seismic Rehabilitation of Buildings, Federal Emergency Management Agency: Washington, D.C., USA.
  15. FEMA 274 (1997), NEHRP Commentary on the guidelines for seismic rehabilitation of buildings, Federal Emergency Management Agency, Washington, D.C., USA.
  16. FEMA 343 (1999), Case Studies: An Assessment of the NEHRP guidelines for the seismic rehabilitation of buildings, Federal Emergency Management Agency, Washington, D.C., USA.
  17. FEMA 356 (2000), Prestandard and Commentary for the Seismic Rehabilitation of Buildings, Federal Emergency Management Agency, Washington, D.C., USA.
  18. FEMA P-58-1 (2012), Seismic Performance Assessment of Buildings Volume 1- Methodology, Washington, D.C., USA.
  19. GB 50011-2010 (2010), Code for Seismic Design of Buildings, Architecture & Building Press, Beijing, Ministry of Housing and Urban-Rural Development of the P.R. China, China.
  20. GB18306-2015 (2015), General Administration of Quality Supervision, Inspection and Quarantine of P.R.C, Seismic Ground Motion Parameter Zonation Map, Architecture & Building Press, Beijing, China.
  21. JGJ3-2010 (2010), Technical Specification for Concrete Structures of Tall Building, Architecture & Building Press, Beijing, Ministry of Housing and Urban-Rural Development of the P.R. China, China.
  22. Ji, J., Xiao, Q. and Huang, C. (2010), "Research on deformation limits of performance-based RC shear walls controlled by flexure", J. Build. Struct., 31(9), 35-41.
  23. LATBSDC (2008), An Alternative Procedure for Seismic Analysis and Design of Tall Buildings Located in the Los Angeles Region, Los Angeles Tall Buildings Structural Design Council: Los Angeles, CA, USA.
  24. Lee, H.S. and Jeong, K.H. (2018), "Performance-based earthquake engineering in a lower-seismicity region: South Korea", Earthq. Struct., 15(1), 45-65. https://doi.org/10.12989/eas.2018.15.1.045.
  25. Lu, X., Ye, L., Ma, Y. and Tang, D. (2012), "Lessons from the collapse of typical RC frames in Xuan-kou school during the Great Wen-chuan Earthquake", Adv. Struct. Eng., 15(1), 139-153. https://doi.org/10.1260/1369-4332.15.1.139.
  26. Moehle, J., Bozorgnia, Y., Jayaram, N., Jones, P., Rahnama, M., Shome, N., Tuna, Z., Wallace, J., Yang, T. and Zareian. F. (2011), "Case studies of the seismic performance of tall buildings designed by alternative means", PEER Report 2011/05, Pacific Earthquake Engineering Research Center, Berkeley, CA, USA.
  27. Mun, J. and Yang, K. (2016), "Displacement ductility ratio-based flexural design approach of reinforced concrete slender shear walls", Mag. Concrete Res., 68(8), 409-422. https://doi.org/10.1680/jmacr.15.00113.
  28. Panagiotou, M., Visnjic, T., Antonellis, G., Galanis, P. and Moehle, J.P. (2013), "Effect of hoop reinforcement spacing on the cyclic response of large reinforced concrete special moment frame beams", PEER Report 2013/16, Pacific Earthquake Engineering Research (PEER) Center, College of Engineering, University of California, USA.
  29. Parrotta, J.E., Peiretti, H.C., Gribniak, V. and Caldentey, A.P. (2014), "Investigating deformations of RC beams: experimental and analytical study", Comput. Concrete, 13(6), 1-27. https://doi.org/10.12989/cac.2014.13.6.799.
  30. PERFORM 3D (2011), Nonlinear Analysis and Performance Assessment for 3D Structures User Guide, Version 5, Computers and Structures, Inc., Berkeley, CA, USA.
  31. Qi, Y.L., Han, X.L. and Ji, J. (2013), "Failure mode classification of reinforced concrete column using Fisher method", J. Central South Univ., 20, 2863-2869. https://doi.org/10.1007/s11771-013-1807-1.
  32. Ricci, P., Verderame, G. and Manfredi, G. (2012), "ASCE/SEI 41 Provisions on deformation capacity of older-type reinforced concrete columns with plain bars", J. Struct. Eng., 139, 04013014. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000701.
  33. SEAONC (2007), Requirements and Guidelines for the Seismic Design and Review of New Tall Buildings using Nonprescriptive Seismic-Design Procedures, Structural Engineers Association of Northern California, San Francisco, CA, USA.
  34. Sezen, H. and Moehle, J.P. (2004), "Shear strength model for lightly reinforced concrete columns", J. Struct. Eng., 130(11), 1692-1703. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:11(1692).
  35. Sharma, K., Deng, L. and Noguez, C.C. (2016), "Field investigation on the performance of building structures during the April 25, 2015 Gorkha earthquake in Nepal", Eng. Struct., 121, 61-74. https://doi.org/10.1016/j.engstruct.2016.04.043.
  36. Siahos, G. and Dritsos, S. (2010), "Procedural assumption comparison for old buildings via pushover analysis including the ASCE 41 update", Earthq. Spectra, 26, 187-208. https://doi.org/10.1193/1.3272266.
  37. Sozen, M.A. (1981), "Review of earthquake response of RC buildings with a view of drift control", State of the Art in Earthquake Engineering, Proceedings of the 7th World Conference on Earthquake Engineering, Istanbul, Turkey January.
  38. Tang, Y., Zheng, Q. and Lou, M. (2012), "Optimization of seismic performance objectives based on cost-effectiveness criterion", J. Tongji Univ. (Nat. Sci.), 40(11), 1613-1619. https://doi.org/10.3969/j.issn.0253-374x.2012.11.005
  39. TBI (2010), "Guidelines for performance-based seismic design of tall buildings", PEER Report 2010/05, The TBI Guidelines Working Group, Pacific Earthquake Engineering Research Center, University of California, Berkeley, California, USA.
  40. Tian, Y., Lu, X., Lu, X., Li, M. and Guan, H. (2016), "Quantifying the seismic resilience of two tall buildings designed using Chinese and US Codes", Earthq. Struct., 11(6), 1-19. https://doi.org/10.12989/eas.2016.11.6.925.
  41. Vision 2000 (1995), Performance Based Seismic Engineering of Buildings, Structural Engineers Association of California, Oakland, USA.
  42. Wallace, J.W., Massone, L.M. and Orakcal, K. (2006), "Analytical modeling of reinforced concrete walls for predicting flexural and couple-shear-flexural responses", PEER Report 2006/07, Pacific Earthquake Engineering Research (PEER) Center, College of Engineering, University of California, California, USA.

피인용 문헌

  1. Component deformation-based collapse evaluation of RC frame under different collapse criteria vol.21, pp.2, 2019, https://doi.org/10.12989/eas.2021.21.2.113