DOI QR코드

DOI QR Code

Deep X-ray Mask with Integrated Micro-Actuator for 3D Microfabrication via LIGA Process

3차원 LIGA 미세구조물 제작을 위한 마이크로 액추에이터 내장형 X-선 마스크

  • 이광철 (포항공과대학교 기계공학과) ;
  • 이승섭 (포항공과대학교 기계공학과)
  • Published : 2002.10.01

Abstract

We present a novel method for 3D microfabrication with LIGA process that utilizes a deep X-ray mask in which a micro-actuator is integrated. The integrated micro-actuator oscillates the X-ray absorber, which is formed on the shuttle mass of the micro-actuator, during X-ray exposures to modify the absorbed dose profile in X-ray resist, typically PMMA. 3D PMMA microstructures according to the modulated dose contour are revealed after GG development. An X-ray mask with integrated comb drive actuator is fabricated using deep reactive ion etching, absorber electroplating, and bulk micromachining with silicon-on-insulator (SOI) wafer. 1mm $\times$ 1 mm, 20 $\mu$m thick silicon shuttle mass as a mask blank is supported by four 1 mm long suspension beams and is driven by the comb electrodes. A 10 $\mu$m thick, 50 $\mu$m line and spaced gold absorber pattern is electroplated on the shuttle mass before the release step. The fundamental frequency and amplitude are around 3.6 kHz and 20 $\mu$m, respectively, for a do bias of 100 V and an ac bias of 20 $V_{p-p}$ (peak-peak). Fabricated PMMA microstructure shows 15.4 $\mu$m deep, S-shaped cross section in the case of 1.6 kJ $cm^{-3}$ surface dose and GG development at 35$^{\circ}C$ for 40 minutes.

Keywords

References

  1. Becker, E. W., Ehrfeld, W., Hagmann, P., Maner, A., and Miinchmeyer, D., 1986, 'Fabrication of Microstructures with High Aspect Ratios and Great Structural Heights by Synchrotron Radiation Lithography, Galvanoforming, and Plastic Moulding (LIGA Process),' Microelectron. Eng., Vol. 4, pp. 35-56 https://doi.org/10.1016/0167-9317(86)90004-3
  2. Guckel, H., Fischer, K., and Stiers, E., 1998, 'Closed Loop Controlled, Large Throw, Magnetic Linear Microactuator with 1000${\mu}m$ Structural Height,' Proc. IEEE Int. Conf. on Micro Electro Mechanical Systems (MEMS'98), pp. 41-18 https://doi.org/10.1109/MEMSYS.1998.659792
  3. Rogge, B., Schulz, J., Mohr, J., Thommes, A., and Menz, W., 1995, 'Fully Batch Fabricated Magnetic Microactuators using a Two Layer LIGA Process,' Proc. Int. Conf. On Solid-State Sensors and Actuators (Transducers '95), pp. 320-323 https://doi.org/10.1109/SENSOR.1995.717183
  4. Samper, V. D., Sangster, A. J., Reuben, R. L., and Wallrabe, D., 1999, 'Torque Evaluation of a LIGA Fabricated Electrostatic Micromotor,' J. of Microelectromech. Sys., Vol. 8(1), pp. 115-123 https://doi.org/10.1109/84.749410
  5. Strohtrnann, M., Bley, P., Fromhein, O., and Mohr, J., 1994, 'Acceleration Sensor with Integrated Compensation of Temperature Effects Fabricated by the LIGA Process,' Sen. and Act. A, Vol. 41-42, pp. 426-429 https://doi.org/10.1016/0924-4247(94)80026-X
  6. Schumacher, K., Kromer, O., Wallrabe, D., Mohr, J., and Saile, V., 1999, 'Micromechanical LIGA-Gyroscope,' Proc. Int. Conf. On Solid-State Sensors and Actuators (Transducers '99), pp. 1574-1577
  7. Muller, K. -D., Bacher, W., and Heckele, M., 1998, 'Flexible Integration of Nonsilicon Microstructures on Microelectronic Circuits,' Proc. IEEE Int. Conf. on Micro Electro Mechanical Systems (MEMS'98), pp. 263-267 https://doi.org/10.1109/MEMSYS.1998.659765
  8. Dunkel, K., Bauer, H. -D., Ehrfeld, W., HoBfeld, J., Weber, L., Horcher, G., and Muller, G., 1998 'Injection-moulded Fibre Ribbon Connectors for Parallel Optical Links Fabricated by the LIGA Technique,' J. Micromech. Microeng., Vol. 8, pp. 301-306 https://doi.org/10.1088/0960-1317/8/4/007
  9. Schulze, J., Ehrfeld, w, HoBfeld, J., Klaus, M., Kufner, M., Kufner, S., Muller, H., and Picard, A., 1999, 'Parallel Optical Interconnection using Selfadjusting Microlenses on Injection Molded Ferrules Made by LIGA Technique,' Proc. SPIE, Vol. 3737, pp 562-571 https://doi.org/10.1117/12.360052
  10. Guckel, H., 1998, 'High-Aspect-Ratio Micromachining Via Deep X-ray Lithography,' Proc. of the IEEE, Vol. 86(8), pp. 1586-1593 https://doi.org/10.1109/5.704264
  11. Christenson, T. R. and Schmale, D. T., 1999, 'A Batch Wafer Scale LIGA Assembly and Packaging Technique via Diffusion Bonding,' Proc. IEEE Int. Conf on Micro Electro Mechanical Systems (MEMS'99), pp. 476--481 https://doi.org/10.1109/MEMSYS.1999.746875
  12. Pan, L. -W. and Lin, L., 2001, 'Batch Transfer of LIGA Microstructures by Selective Electroplating and Bonding,' J. of Microelectromech. Sys., Vol. 10(1), pp. 25-32 https://doi.org/10.1109/84.911088
  13. Maas, D., Bustgens, B., Fahrenberg, J., Keller, W., Ruther, P., Schomburg, W. K., and Seidel, D., 1996, 'Fabrication of Microcomponents using Adhesive Bonding Techniques,' Proc. IEEE Int. Conf. on Micro Electro Mechanical Systems (MEMS'96), pp. 331-336 https://doi.org/10.1109/MEMSYS.1996.494003
  14. Ehrfeld, W. and Schmidt, A., 1998, 'Recent Developments in Deep X-ray Lithography,' J. Vac. Sci. Technol. B, Vol. 16(6), pp. 3526-3534 https://doi.org/10.1116/1.590490
  15. Feinerman, A. D., Lajos, R. E., White, V., and Denton, D. D., 1996, 'X-ray Lathe: an X-ray Lithographic Exposure Tool for Nonplanar Objects,' J. of Microelectromech. Sys., Vol. 5(4), pp. 250-255 https://doi.org/10.1109/84.546405
  16. Katoh, T., Nishi, N., Fukugawa, M., Ueno, H., and Sugiyama, S., 2001, 'Direct Writing for Threedimensional Microfabrication using Synchrotron Radiation Etching,' Sen. and Act. A, Vol. 89, pp. 10-15 https://doi.org/10.1016/S0924-4247(00)00528-8
  17. Sugiyama, S. and Veno, H., 2001, 'Novel Shaped Microstructures Processed by Deep X-ray Lithography,' Proc. Int. Conf. On Solid-State Sensors and Actuators (Transducers'01), pp. 1574-1577
  18. Tabata, O., Matsuzuka, N., Yamaji, T., and You, H., 2001, 'Fabrication of 3-dimensional Microstructures using Moving Mask Deep X-ray Lithography ($M^2DXL$),' Proc. IEEE Int. Conf. on Micro Electro Mechanical Systems (MEMS'01), pp. 94-97 https://doi.org/10.1109/MEMSYS.2001.906487
  19. Tabata, O., Matsuzuka, N., Yamaji, T., Vemura, S., and Yamamoto, K., 2002, '3D Microfabrication by Moving Mask Deep X-ray Lithography ($M^2DXL$) with Multiple Stages,' Proc. IEEE Int. Conf. on Micro Electro Mechanical Systems (MEMS'02), pp. 180-183 https://doi.org/10.1109/MEMSYS.2002.984234
  20. Cheng, Y., Kuo, N. -Y., and Su, C. H., 1997, 'Dose Distribution of Synchrotron X-ray Penetrating Materials of Low Atomic Numbers,' Rev. Sci. Instrum., Vol. 68(5), pp. 180-183 https://doi.org/10.1063/1.1148067
  21. Koo, Y. and Shin, N., 2000, X-ray Science & Applications (In Korean), A-Jin, Seoul, pp. 29-64