• Journal of the Korean Applied Science and Technology
• /
• v.34 no.3
• /
• pp.650-656
• /
• 2017

The water-swollen hydrogels containing silicone or fluorine were prepared by copolymerization of 2-hydroxy ethyl methacylate (HEMA) with 3-(trimethoxysilyl)propyl methacrylate(SM) or 2,2,2-trifluoroethyl acrylate(FA). When the content of SM or FA increased in copolymers, there was tendency of water absorbance to decrease, whereas contact angles to increase. The hydrogels containing FA showed 2 ~ 4% higher water content and 4 ~ 5% lower contact angles compared to that of SM. Tensile strengths decreased as the content of SM increased. However, FA exhibited strength of $2.2Mpa/cm^2$ which is similar to $2.3Mpa/cm^2$ of B. FA, which implies comparatively low adherence, hence, showed better protein resistance properties than SM-based hydrogel. The photo-polymerization was also applied instead of thermal polymerization to enhance the energy efficiency. As a result, the reaction yield reached over 95% within 1 minute.

• Journal of the Korean Ceramic Society
• /
• v.33 no.3
• /
• pp.251-258
• /
• 1996

The reactions between an active metal brazing alloy and interlayers together with the effects of interlayer type on the interfacial microstructure change were investiaged for silicon nitride/stainless steel joint. The bending strengths were measured for joints with Mo, Cu, Ni interlayer type of different thicknesses. It was found that the interlayer with a low yield strength value is effective to improve the bending strength of the Si3N4/stainless steel joint. The maximum joint strength obtained at room temperature for a laminated Cu/Mo interlayer was about 460 MPa. The combined use of Mo and thin Cu layer was found to be effective in enhancing the bending strength for the Si3N4/S.S.316 joint.

• Fibers and Polymers
• /
• v.2 no.4
• /
• pp.178-183
• /
• 2001

A pitch precursor for a general purpose carbon fiber was prepared by condensation of pyrolized fuel oil (petroleum residual oil) with bromine under nitrogen blowing. such a condensation raised the softening point of the pitch from 4$0^{\circ}C$ to $265^{\circ}$ with a yield of 43%. The pitch precurosr showed an enhanced aromaticity and enlarged molecular size, which led to a reduction in molecular mobility and optical isotropy. The precursor was spun into fibers of $20\mu\textrm{m}$ diameter at a take-up speed of 700m/min. The fiber was stepwise stabilized in air and carbonized in Ar gas to obtain an isotropic carbon fiber. The carbon fiber exhibited tensile strengths of 500-800 ㎫though the fiber was formed via a crude method. The electric conductivity of the carbon fiber was relatively high, 2.2$\times$$10^2$S/cm, sufficient to be used as electrode materials.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1996.04a
• /
• pp.312-316
• /
• 1996

Flexural fatigue strength of reinforced concrete members can be controlled by fatigue characteristics of concrete and reinforcing bars because the reinforced concrete members are composite members consisted of the concrete and the reinforcing bars. Since the fatigue characteristics of the reinforcing bars are different from static strength characteristics of those, it is necessary to obtain the fatigue characteristics of reinforcing bars directly from fatigue test. In this paper, the fatigue characteristics like fatigue strength of reinforcing bars with different diameters and different yield-strengths are obtained experimentally and the analysis and comparison of fatigue test results are presented. For the experiment, most widely used reinforcing bars manufactured by two domestic companies were randomly selected and direct tension fatigue tests were performed.

• Journal of the Korean Society of Safety
• /
• v.26 no.2
• /
• pp.1-5
• /
• 2011

In order to evaluate fatigue endurance for an ultra-light weight inline skate frame, FEM analysis was performed. Tensile properties and a S-N curve were determined through tensile and fatigue tests on a modified Al-7075+$S_c$ alloy. The yield and ultimate tensile strengths were 553.3 MPa and 705.5 MPa, respectively. The fatigue endurance limit of this alloy was 201.2 MPa. For evaluating the fatigue endurance of the inline skate frame, the S-N data were compared with the stress analysis results through FEM analysis of the frame. The maximum Von-Mises stress of the frame was determined 106 MPa through FEM analysis of the frame, assuming that the rider weight is 75 Kg. Conclusively, on the basis of fatigue limit, the inline skate frame has a safety factor of approximately 2.0.

• Journal of Korea Foundry Society
• /
• v.27 no.4
• /
• pp.159-166
• /
• 2007

Effects of alloying elements on the mechanical properties of 3.60wt%C-2.50wt%Si ductile cast iron with annealing and normalizing were investigated. Yield and tensile strengths were increased from 278 and 415 MPa to 316 and 440 MPa respectively as manganese content was increased upto 0.45wt% while elongation was decreased from 24.2 to 5.0%. The formers were increased and the latter was decreased with the increased amount of copper, molybdenum or nickel added. Meanwhile the tensile strength of annealed specimen was increased with the amount of alloying elements added, it was decreased by annealing. It was increased greatly by normalizing and the amount of alloying elements added except molybdenum.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06b
• /
• pp.451-454
• /
• 2006

This paper presents an overview of ONP deinking efficiency with cellulolytic enzymes and synthetic collector in alkaline pH. Deinking is a series of unit operations designed to detach ink from cellulose fibers and separate the dispersed ink from the pulp slurry. Deinking chemicals are process aids that enable expensive mill equipment used in these unit operations to operate more efficiently - often much more efficiently. We propose the blended deinking agent with cellulolutic enzymes and synthetic collector in deinking pulp of conventional alkaline method. The deinking efficiency of old news print in alkaline pH was enhanced with enzyme treatments. The brightness of deinked pulp was increased with less residual ink particles and yield of enzymatic deinked pulp was improved compared to the deinked pulp of conventional alkaline method.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.6
• /
• pp.898-905
• /
• 1986

In order to obtain the microstructure improving fatigue crack propagation resistance of steels, fatigue crack propagation behavior of martensite-ferrite dual phase steels is investigated in terms of crack deflection and crack closure. The results obtained are as follows; (1) .DELTA.K$_{th}$ and fatigue crack propagation resistance in low .DELTA.K region increases with increasing hardness of second phase. But the difference of this crack propagation resistance decreases with increasing .DELTA.D. (2) In low .DELTA.K region, crack closure increases with increasing hardness of second phase, when the materials have all the sam volume fractionof second phase, or when yield strengths are similar in all materials. (3) These crack closure can be explained by fracture surface roughness due to crack deflection.n.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.299-300
• /
• 2005

Surface friction welding (SFW) is a newly developed technology fur joining thin metal sheets, which utilizes friction between tool and weldment. In the present study, the 5052 and 1050 Al sheets were locally surface-modified using SFW technology. Formability of the locally surface-modified sheets was superior to that of the parent material. Yield or tensile strengths of the locally surface-modified specimens were lower then those of the parent material, but elongations of the locally surface-modified specimens were higher then that of the parent material.

• Transactions of Materials Processing
• /
• v.18 no.6
• /
• pp.482-487
• /
• 2009

A finite element based microstructural modeling for the size dependent strengthening of particle reinforced aluminum composites is presented. The model accounts explicitly for the enhanced strength in a discretely defined "punched zone" around the particle in an aluminum matrix composite as a result of geometrically necessary dislocations developed through a CTE mismatch. The density of geometrically necessary dislocations is calculated considering volume fraction of the particle. Results show that predicted flow stresses with different particle size are in good agreement with experiments. It is also shown that 0.2% offset yield stresses increases with smaller particles and larger volume fractions and this length-scale effect on the enhanced strength can be observed by explicitly including GND region around the particle. The strengths predicted with the inclusion of volume fraction in the density equation are slightly lower than those without.