• Korea Science and Art Forum
• /
• v.37 no.5
• /
• pp.239-248
• /
• 2019

This study started from the need to improve one of shortcomings of synthetic PVAc adhesives - potential physical harm and environmental hazards to the workers or their users. As a matter of fact, PVAc adhesives are currently mainly used because of their convenience and economy for the production of woodcrafts. The purpose of this study was to develop natural adhesives through research on natural adhesives in step with the current increase of societal attention to environmental friendliness and rapid surge in their demand in the face of such problems. So, the study attempted research on the bases to develop natural adhesives for woodcraft, using cellulose extracts from wood - natural adhesive material. The findings of the study were as follows. Firstly, natural adhesives showed the improved effect in the field of adhesive strength, a basic physical property by 0.2 - 4 times compared with the existing materials and the study confirmed they had the similar or stable pH value. Besides, they had good reversibility, demonstrating their basic physical property as a natural adhesive for woodcraft. While, their durability to ultraviolet ray degradation also showed an excellent result value being better by 1.5 - 8.5 times than the existing materials. The study expects natural adhesives with improved and better performances compared with the existing materials could be developed, if further research on adhesive strength, antibiosis, conservative property were to continue by developing refinery technology for cellulose extracts from wood and rendering the functionality to them.

• Journal of Conservation Science
• /
• v.37 no.2
• /
• pp.135-143
• /
• 2021

Conservation treatment that involved filling the lifting parts of wooden cultural heritage is carried out by obtaining wood or wood powder of the same species and mixing it with synthetic resin or natural glue to charge the blank area. Various concentrations and mixing ratios of adhesives and additives are used, depending on the type and condition of the target. Accordingly, in this study, we determined the conditions of the filler suitable for conservation treatment of wooden sculptures with lifted or separated bark in the National Museum of Modern and Contemporary Art. The optimal filler conditions for each adhesive were selected based on drying speed, shrinkage and expansion rates, and physical deformation degree. Then, to verify their actual applicability, these fillers were applied to wood and exposed to high-humidity environment and their cross-sections were observed. The fillers showed stable application in the following order: animal glue, PVAc adhesive, acrylic adhesive. In conclusion, a 1:2 mixture of animal glue and wood powder is a suitable filler for conservation treatment of wooden sculpture with lifted bark. The results of this study suggest appropriate ways to stabilize the bark that was lifted or separated from a wooden sculpture, thus enabling the future conservation treatment of the artworks under similar conditions.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.4
• /
• pp.409-418
• /
• 2017

This work attempted to manufacture glued-laminated timber (Glulam) bonded with melamine-urea-formaldehyde (MUF) resin adhesives at various melamine contents from 20% to 50% under high frequency (HF) heating for a very short time. Two preparation methods were employed to prepare MUF resin adhesives with different melamine contents: one-batch method of synthesizing MUF resins in a single batch, and two-batch method of mixing urea-formaldehyde (UF) resin with melamine-formaldehyde (MF) resin that had been synthesized separately. As the melamine content increased, the gelation time and peak temperature of MUF resins decreased. The adhesion performance of plywood showed that the one-batch MUF resin adhesive with 50% melamine content only satisfied the standard requirement of water resistance. Thus, the one-batch MUF resin adhesive with 50% melamine content was applied for bonding wood lamina from four softwood species such as Japanese larch, Korean red pine, Korean pine and Japanese cedar to manufacture Glulam under HF heating. All Glulam samples bonded with the one-batch MUF resin adhesives with 50% melamine content except those from Korean Red Pine satisfied the requirement in water soaking or boiling water delamination test as an exterior grade Glulam. The presence of rosin in Korean Red Pine was believed to be responsible for its poor adhesion. These results showed that the one-batch MUF resin adhesives with 50% melamine content provided acceptable water resistance with exterior grade Glulam manufactured under HF heating.

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.3
• /
• pp.213-220
• /
• 2018

In order to use Pitch pine (Pinus rigida Miller) as the material of the structural glued laminated timber, the effect of the amount of resin exudation due to storage time after the planning and the knot of the lamina were evaluated on the bonding properties of the glued board with resorcinol resin. For Pitch pine that was dried at high temperature ($120{\sim}95^{\circ}C$) and low temperature ($65{\sim}50^{\circ}C$), the flat sawn(tangential section) showed higher amount of resin exudation than the quarter sawn(radial section). And the low temperature drying wood showed higher resin exudation than the high temperature drying wood. The low and high temperature drying wood showed the highest amount of resin exudation on the 3rd day and 7th day, respectively and they were gradually decreased. However, there were no significant differences from 15 to 90 days. Adhesion performances were low until 2~3 days with high exudation of resin, but there were no significant differences after 15 days. Both high temperature and low temperature drying woods satisfied the Korean standard regardless of the storage time. The adhesive strengths of the laminating parts including knots were higher than those of KS criteria, but the wood failures were not satisfied the KS standard. Adhesive performances according to the laminating combinations (quarter sawn + quarter sawn, flat sawn + flat sawn, quarter sawn + flat sawn) were better than those of KS criteria in all laminating combinations in both high temperature and low temperature drying woods.

• Journal of the Korea Furniture Society
• /
• v.10 no.1
• /
• pp.65-71
• /
• 1999

The bending performance of sloped finger-jointed Rhus verniciflua were tested in order to improve the strength properties of finger-joint. Sloped finger-cut pieces were jointed with three kinds of adhesives (polyvinyl acetate, polyvinyl-acryl acetate and oilic resin). The slope ratios of finger joints were 0, 1.0, 1.5, and 2.0. The MOE, MOR and deflection to maximum load in bending of sloped finger-joints and solid wood specimen were measured. The results were : 1) The efficiencies of MOE to finger and sloped finger-joints to the solid wood were almost same in the three kinds of adhesives(polyvinyl acetate, polyvinyl-acryl acetate and oilic urethane resin) and there were some effect of slope on the MOE in a sloped finger-joint for three kinds of resin adhesives. 2) There was the effect of slope on the MOR in sloped finger-joints in every kind of adhesive. The efficiencies of MOR in slope ratios of 0 and 2.0 ranged 65-79%, respectively. There was also a slight effect of the kinds of adhesives on the MOR. However, the efficiencies of deflection to the urethane resin adhesive were much less than those of polyvinyl acetate, polyvinyl-acryl acetate resin adhesives except the slope ratio of 0. 3) It might be impossible to estimate the bending stregth of sloped finger-jointed Rhus verniciflua by using MOE. The correlation coefficient(0.192) between MOE was very low and not significant at 5% level.

• Journal of Adhesion and Interface
• /
• v.21 no.4
• /
• pp.135-142
• /
• 2020

Recently, people's interest in eco-friendly plastics derived from nature to replace petroleum-based plastics is increasing due to environmental problems such as microplastics. In line with this trend, eco-friendly adhesives using natural materials and processes are also being developed in the adhesive field. Among them, maltose is a natural substance derived from starch and is the main component of starch syrup used as a food additive. Due to its lower molecular weight than starch, it is easily soluble in water, and above all, there is a possibility that it can be copolymerized with other monomers through solution polymerization. However, researches related to the application of maltose to adhesives are very rare. In this study, after modifying maltose using acrylic anhydride, the product was analyzed through FT-IR and H-NMR. And the modified maltose was copolymerized with two kinds of acrylic monomers. The synthesized adhesive was applied on the wood and the adhesive performance were investigated.

• Journal of the Korea Furniture Society
• /
• v.11 no.1
• /
• pp.25-29
• /
• 2000

This study was carried out to analyze the ultrasonic properties of sound board which was glued with various adhesives and to evaluate which adhesive is the best for the acoustic radiation of the musical instrument. The results are as follows: 1. Animal glue is the best adhesive for the sound board with respect to the acoustic radiation ratio of the musical instruments. Epoxy resin and polyvinyl acetate resin are the next group, urea formaldehyde resin and Hot melt are the third group, polychloroprene(CR) resin is the lowest. 2. Epoxy resin, animal glue and Titebond(PVA) give the highest shear strength and the highest wood failure relatively Hot melt and polychloroprene(CR) resin do not meet the standard because of low wood failure.

• Journal of the Korean Wood Science and Technology
• /
• v.26 no.4
• /
• pp.50-55
• /
• 1998

This study was carried out to develop low density board made of rice hull which needs proper use. Urea formaldehyde adhesive(UF) was used. The raw materials were the mixtures of the rice hulls from IllFum, DongGin, ChuChong, etc. The physical and mechanical properties of rice hull insulation board were examined. The results are as follows : For the thickness of 15mm of the low density rice hull board bonded with UF resin, proper manufacturing conditions were $171^{\circ}C$ of hot pressing temperature with thickness bar for optimum density, 12 percent of resin solid contents of rice hull ovendry weight, and 20 minutes of hot pressing time. These conditions meet Korean standards(KS 3201-1982) in relation to free formaldehyde emission, bending strength, water absorption and heat resistance.

• Journal of the Korean Wood Science and Technology
• /
• v.26 no.4
• /
• pp.92-97
• /
• 1998

Four urea-formaldehyde (UF) resins were synthesized as a particleboard (PB) binder with the four different initial formaldehyde/urea mole ratio and the final mole ratio of 1.15. The UF resins were characterized according to the standard method of resin adhesive analysis. PBs were manufactured using liquid UF resins at 5 minutes press time and 6% resin solids levels on an ovendry particle weight basis. A total of 20 PBs was fabricated for 5 panel replication per UF resin types. The panels were tested for physical strength properties per the procedure ASTM D 1037. The formaldehyde emission levels from the PBs bonded with the UF resins were tested according to 2-hour desiccator test method ASTM D 5582. There were no significant differences among UF resin types for internal bond strength of PBs. But there were significant differences among UF resin types for formaldehyde emission level of PBs. The results showed that the formaldehyde emission level was influenced by the UF resin types without reducing the adhesive performance.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.2
• /
• pp.37-45
• /
• 2006

The viscoelastic properties of blends of melamine-formaldehyde (MF) resin and poly(vinyl acetate) (PVAc) for engineered flooring used on the Korean traditional ONDOL house floor heating system were investigated by dynamic mechanical thermal analysis (DMTA). Because MF resin is a thermosetting adhesive, the effect of MF rein was shown across all thermal behaviors. The addition of PVAc reduced the curing temperature. The DMTA thermogram of MF resin showed that the storage modulus (E') increased as the temperature was further increased as a result of the cross-linking induced by the curing reaction of the resin. The storage modulus (E') of MF resin increased both as a function of increasing temperature and with increasing heating rate. From isothermal DMTA results, peak $T_{tan{\delta}}$ values, maximum value of loss modulus (E") and the rigidities (${\Delta}E$) of MF/PVAc blends at room temperature as a function of open time, peak $T_{tan{\delta}}$ and maximum loss modulus (E") values were found to increase with blend MF content. Moreover, the rigidities of the 70:30 and 50:50 MF/PVAc blends were higher than those of the other blends, especially of 100% PVAc or MF. We concluded that blends the MF/PVAc blend ratios correlate during the adhesion process.