• Journal of the Korea Convergence Society
• /
• v.12 no.2
• /
• pp.215-219
• /
• 2021

The flow analyses around the wing of airplane installed with winglet or sharkelt were carried out in this study. At the model without winglet, it can be seen that the air flows beside the wing and the flow is concentrated at the end of wing. At the model of winglet or sharklet, the pressure on the bottom of the wing happens to be lower in the wide area than for model without winglet. At the analysis result, the air flowing next to the wing can be seen to go over and rotates over the main wing. The model with the sharklet shows that the flow rate is the fastest. In case of model with sharklet, it is thought that the maximum total pressure of flow is distributed at the bottom of the wing, which can further improve the lift force of the wing. It is thought that the analysis results in this study on the air flow due to the configuration of aircraft edge wing can be helped at its convergent research.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3209-3214
• /
• 2007

This study numerically investigates the unsteady flow and acoustic characteristics of a flapping wing using a hydrodynamic/acoustic splitting method. The Reynolds number based on the maximum translation velocity of the wing is Re=8800 and Mach number is M=0.0485. The flow around the flapping wing is predicted by solving the two-dimensional incompressible Navier-Stokes equations (INS) and the acoustic field is calculated by the linearized perturbed compressible equations (LPCE), both solved in moving coordinates. Numerical results show that the hovering sound is largely generated by wing translation (transverse and tangential), which have different dipole sources with different mechanisms. As a distinctive feature of the flapping sound, it is also shown that the dominant frequency varies around the wing.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.spc3
• /
• pp.269-274
• /
• 2012

The research of the biological mimics robot which utilizes the operation of the organism is progressed on the ground, aerial, and underwater robot sector. In the field of flying robot, the research for implementing the wing movement structure of the bird and insect is progressed. The joint structure for the wing movement of the bird is implemented. The operation of the wing is simulated. For this purpose, by using the Matlab/Simulink, the joint structure of the wing is modelled. The joint movement of the wing is tested through the simulation.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.389-394
• /
• 2007

Numerical simulations are conducted to investigate the mechanism for force generation of an insect with tandem wing configuration. Various stroke amplitudes, stroke plane angles and phase difference between the fore- and hind-wings are considered. The Reynolds number is 150 based on the chord length and maximum translation velocity of the wing. When an insect requires high lift such as takeoff, it flaps its wings in parallel at a lower stroke plane angle and a bigger stroke amplitude than those in the hovering. With wings in counter-stroke, the lift fluctuations decrease, and moreover mean lift force decreases. Interactions among the fore-wing, hind-wing and vortices are examined to explain the force variations

• International Journal of Aeronautical and Space Sciences
• /
• v.8 no.1
• /
• pp.87-94
• /
• 2007

Tilt rotor-wing concept to show enhanced performance in low speed mission is presented. Three types of stud wings on the existing tilt rotor configuration are suggested and their characteristics are compared. Aerodynamic analysis indicates that the stud wing concept gives significant performance improvement on the endurance and range in the low speed regime when compared with the tilt rotor. Penalties of the stud wing are discussed from the perspectives of conversion corridor, structural weight, configuration design, and cross wind stability. This study concludes that the advantage of the stud wing in general UAV mission performance is so significant as to surpass the penalties in other perspectives investigated.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.1
• /
• pp.23-27
• /
• 2011

This study analyzes about the variation of pressure and stream velocity according to the movement of tail wing. The pressure at the front part of airplane becomes lower than at the rear part and the stream velocity has decreased by being bumped against the wing of airplane. The pressure at the front part of rudder becomes higher than at its rear part according to the movement of rudder among the tail wings of airplane. The more stream velocity becomes decreased, the more rudder spreads out. As the tail wing of airplane folds, the pressure at its front part becomes higher. And the pressure at its rear part becomes lower than at its front part. The more tail wing of airplane folds, the more stream velocity becomes decreased.

• Journal of Mechanical Science and Technology
• /
• v.20 no.7
• /
• pp.1051-1058
• /
• 2006

The steady aerodynamic characteristics of a wing flying over a channel are investigated using a boundary-element method. The present method is validated by comparing the computed results with the measured data. Compared with a flat ground surface, the channel fence augmented the lift increase and induced drag reduction. When the fence is lower than the wing height, the gap between the wingtip and the fence does not affect the aerodynamic characteristics of the wing much. When the fence is higher than the wing height, the close gap increased the lift. The induced drag is reduced when the wing is placed near the ground or at the same height as the fence. It is believed that present results can be used in the conceptual design of the high-speed ground transporters flying over the channel.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.404-405
• /
• 2012

The research of the biological mimics robot which utilizes the operation of the organism and which it applies to the robot is progressed on the ground, aerial, and underwater robot sector. In the field of flying robot, the research for implementing the wing movement structure of the bird and insect is progressed. The joint structure for the wing movement of the bird is implemented. The operation of the wing is simulated. For this purpose, by using the Matlab/Simulink, the joint structure of the wing is modelled. The joint movement of the wing is tested through the simulation.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.696-702
• /
• 2006

Flutter characteristics of composite curved wing were investigated in this study. The efficient and robust system for the flutter optimization of general composite curved wing models has been developed using the coupled computational method based on both the standard genetic algorithm and the micro genetic algorithms. Micro genetic algorithm is used as an alternative method to overcome the relatively poor exploitation characteristics of the standard genetic algorithm. The present results show that the micro genetic algorithm is more efficient in order to find optimized lay-ups for a composite curved wing model. It is found that the flutter stability of curved wing model can be significantly increased using composite materials with proper optimum lamination design when compared to the case of isotropic wing model under the same weight condition.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.203-206
• /
• 2006

In this study, the method of designing the flexible wing model which will be used for wind tunnel testing of gust response alleviation system was presented. The design concept proposed herein was validated by performing the modal testing of the flexible wing model manufactured for demonstration purpose. In addition, the study on the gust response alleviation using flexible wing control surface was performed. For this purpose, optimal control with output feedback was adopted for designing the control surface controller, and the effects of gust response alleviation was validated by performing the numerical simulation for the representative flexible wing model. The methods proposed and validated in this study can be applied for wind tunnel testing of the flexible wing for gust response alleviation.