• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제55권5호
• /
• pp.239-244
• /
• 2006

To drive the high-image quality plasma displays of XGA and/or full-HD, we must effectively improve the driving waveform, which get the reset period for the stabilized control of wall charges, the address period to select discharge or non-discharge, and sustain period for luminance in 1 TV-frame, and also the display quality. To accomplish them, the development of the technology for the fast address discharge is required. In this paper, the correlation between the sustain-electrode gap and address discharge characteristics for the high-speed addressing was analyzed using the measurements of dynamic voltage margins. Results showed that the narrower the gap between the sustain electrodes, the narrower the with of the scan pulse became and a dynamic margin of data voltage of 29.2 V was obtained at scan pulse width of $1.0{\mu}s\;and\;V_{ramp}$ of 240 V for driving 4-inch test penal, which the gap between sustain electrodes was $65{\mu}m$.

• Tribology and Lubricants
• /
• 제39권2호
• /
• pp.61-71
• /
• 2023

This study proposes a procedure for designing a labyrinth seal that meets both leakage flow rate and rotordynamic performance criteria (effective damping, amplification factor, separation margin, logarithmic decrement, and vibration amplitude). The seal is modeled using a one control volume (1CV) bulk flow approach to predict the leakage flow rate and rotordynamic coefficients. The rotating shaft is modeled with the finite element (FE) method and is assumed to be supported by two linearized bearings. Geometry, material and operating conditions of the rotating shaft, and the supporting characteristics of the bearings were fixed. A single labyrinth seal is placed at the center of the rotor, and the linearized dynamic coefficients predicted by the seal numerical model are inserted as linear springs and dampers at the seal position. Seal designs that satisfy both leakage and rotordynamic performance are searched by modifying five seal design parameters using the multi-grid method. The five design parameters include pre-swirl ratio, number of teeth, tooth pitch, tooth height and tooth tip width. In total, 12500 seal models are examined and the optimal seal design is selected. Finally, normalization was performed to select the optimal labyrinth seal designs that satisfy the system performance requirements.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.694-699
• /
• 2002

As the demand for slim laptops requires ion'-height optical disc drives, vibration problems of optical disc drives are of great concern. Additionally, with the decrease of a track width and a depth of focus in high density drives, studies on vibration resonance between mechanical parts become more important. From the vibration point of view, the performance of optical disc drives is closely related with the relative displacement between a disc and an objective lens which is controlled by servo mechanism. In other words, to read and write data properly, the relative displacement between an optical disc and an objective lens should be within a certain limit. The relative displacement is dependent on not only an anti-vibration mechanism design but also servo control capability. Good servo controls can make compensation for poor mechanisms, and vice versa. In a usual development process, robustness of the anti-vibration mechanism is always verified with the servo control of an objective lens. Engineers partially modify servo gain margin in case of a data reading error. This modification cannot correct the data reading error occasionally and the mechanism should be redesigned more robustly. Therefore it is necessary to verify a mechanism with respect to the possible servo gain plot. In this study we propose the experimental verification method far anti-vibration mechanism with respect to the existing servo gain plot. This method verifies axial vibration characteristics of optical disc drives on the basis of transmissibility. Using this method, we verified our mechanism and modified the mechanism for better anti-vibration characteristics.

• 한국소음진동공학회논문집
• /
• 제12권11호
• /
• pp.833-839
• /
• 2002

As the demand for slim laptops requires low-height optical disc drives, vibration problems of optical disc drives are of great concern. Additionally, with the decrease of a track width and a depth of focus in high density drives, studies on vibration resonance between mechanical parts become more important. From the vibration point of view, the performance of optical disc drives is closely related with the relative displacement between a disc and an objective lens which is controlled by servo mechanism. In other words, to read and write data properly, the relative displacement between an optical disc and an objective lens should be within a certain limit. The relative displacement is dependent on not only an anti-vibration mechanism design but also servo control capability. Good servo controls can make compensation for poor mechanisms, and vice versa. In a usual development process, robustness of the anti-vibration mechanism is always verified with the servo control of an objective lens. Engineers partially modify servo gain margin in case of a data reading error. This modification cannot correct the data reading error occasionally and the mechanism should be redesigned more robustly. Therefore it is necessary to verify a mechanism with respect to the possible servo gain plot. In this study we propose the experimental verification method for anti-vibration mechanism with respect to the existing servo gain plot. Thismethod verifies axial vibration characteristics of optical disc drives on the basis of transmissibility. Using this method, we verified our mechanism and modified the mechanism for better anti-vibration characteristics.

• 전기전자학회논문지
• /
• 제12권3호
• /
• pp.176-183
• /
• 2008

본 논문에서는 DTMOS(Dynamic Threshold voltage MOSFET) 스위칭 소자를 사용한 고 효율 전원 제어 장치 (PMIC)를 제안하였다. 높은 출력 전류에서 고 전력 효율을 얻기 위하여 PWM(Pulse Width Modulation) 제어 방식을 사용하여 PMIC를 구현하였으며, 낮은 온 저항을 갖는 DTMOS를 설계하여 도통 손실을 감소시켰다. 벅 컨버터(Buck converter) 제어 회로는 PWM 제어회로로 되어 있으며, 삼각파 발생기(Saw-tooth generator), 밴드갭기준 전압 회로(Band-gap reference circuit), 오차 증폭기(Error amplifier), 비교기(Comparator circuit)가 하나의 블록으로 구성되어 있다. 삼각파 발생기는 그라운드부터 전원 전압(Vdd:3.3V)까지 출력 진폭 범위를 갖는 1.2MHz 발진 주파수를 가지며, 비교기는 2단 연산 증폭기로 설계되었다. 그리고 오차 증폭기는 70dB의 DC gain과 $64^{\circ}$ 위상 여유를 갖도록 설계하였다. Voltage-mode PWM 제어 회로와 낮은 온 저항을 스위칭 소자로 사용하여 구현한 DC-DC converter는 100mA 출력 전류에서 95%의 효율을 구현하였으며, 1mA이하의 대기모드에서도 높은 효율을 구현하기 위하여 LDO를 설계하였다.

• Journal of Periodontal and Implant Science
• /
• 제25권2호
• /
• pp.301-320
• /
• 1995

The purpose of this study was to evaluate a new biodegradable membrane - atelocollagen as a guided tissue regeneration barrier on the dehiscence defects adjacent to the dental implants. 3 beagle dogs were selected for this study and all the mandibular premolars($P_1,P_2,P_3&P_4$) were extracted. Twelve weeks after the extraction, the edentulous ridges were formed to be placed the titanium plasma-sprayed IMZ implants. Four implant osteotomies were performed on each side of the mandible. The osteotomies were placed facially in the edentulous ridges to approximate an actual dehiscence defect as closely as possible, The standardized dehiscence defects were created 3 mm in width and 4 mm in height by osteotomy. A total 24 implants were placed. e-PTFE, ateloco11agen and $Collatape^{(R)}$ were placed to cover the defects and the one defect served as a control, not covered any membrane. By random selection, three dogs were sacrificed at 2 weeks, 4weeks and 8 weeks after fixation with 3% glutaraldehyde. A week before sacrificing, 8-week dog was infused intravenously with oxy-tetracycline 30mg/kg. The left mandibular blocks were used for full decalcified histologic preparation and the right mandibular blocks were selected for undeca1cified preparation, At 2 weeks, the regenerated bone of e-PTFE and atelocollagen groups appeared to be more dense than other groups and the percentage of bone defect fill was highest for e-PTFE and follwed by ateloco1lagen group. However, the $Collatape^{(R)}$ and control groups showed a little new bone formation. $Collatape^{(R)}$ was almost degraded within 2 weeks. At 4 weeks, the regenerated new bone were much greater and denser than at 2 weeks for e-PTFE and ateloco11agen group. Although a part of atelocollagen bagan to be degraded at the margin and surrounded by foreign body giant cells related to foreign body reaction, it was generally intact and the regenerated new bone was shown much more than at 2 weeks. The amount of new bone in $Collatape^{(R)}$ and control groups at 4 weeks were similar to that of 2 weeks group. At 8 weeks, the regenerated bone was matured and observed along the implant fixture. Direct new bone formation and calcium deposits beneath the e-PTFE were observed. No further bone growth was seen in the $Collatape^{(R)}$ and control groups. In reflected fluoromicrcocopic observation, the osteogenic activity was pronounced between e-PTFE membrane and the old bone. High osteogenic activity was also observed in atelocol1agen group. This study suggested that the ateloco11agen as well as e-PTFE could be used for guided tissue regeneration on dehiscence defects adjacent to the dental implants. But the $Collatape^{(R)}$ was completely resorbed within 2 weeks and was not a suitable membrane for guided bone regeneration.

• 대한소아치과학회지
• /
• 제35권2호
• /
• pp.259-267
• /
• 2008

구치부 인접면 와동에서 유동성 복합레진 이장재의 두께가 치은측 변연의 미세누출에 미치는 영향을 평가하기 위하여 발거된 소구치 및 대구치의 근, 원심면에 box 형태의 와동(협설폭경 3mm, 근원심폭경 2mm, 상아법랑경계 상방 1mm에 치은 변연) 120개를 형성한 뒤, 무작위로 30개씩 선정하여 다음과 같은 4개의 군으로 분류하였다. group I- Tetric ceram 충전군(대조군) group II- 0.5mm 두께의 Tetric flow + Tetric ceram group III- 1.5mm 두께의 Tetric flow + Tetric ceram group IV- 2.5mm 두께의 Tetric flow + Tetric ceram 색소침투법으로 치은측 변연부 미세누출을 측정하여 다음과 같은 결론을 얻었다. 1. group II는 group I에 비해 낮은 미세누출을 보였다(p<0.05). 2. group III, IV과 group I 사이에는 통계적으로 유의한 미세누출의 차이가 없었다(p>0.05). 3. group II는 group III, IV에 비해 낮은 미세누출을 보였다(p<0.05). 4. 모든 group에서 정도의 차이는 있으나 치경부에서 미세누출을 보였다. 이상의 결과로, 혼합형 복합레진으로의 구치부 인접면 와동 수복시 0.5mm 두께의 유동성 레진으로의 와동저 이장은 치은측 변연의 봉쇄능을 향상시켜 변연부 미세누출을 감소시킬 수 있는 방법으로 사료된다.

• 한국제4기학회지
• /
• 제9권1호
• /
• pp.33-42
• /
• 1995

우리나라의 서해(West Sea)는 일명 황해(Yellow Sea)라고 일컬어지는 약 40여 m의 평균 수심을 갖는 대륙붕 해저지형 분지에 의하여 지배되는 전형적 육연해이다, 그런데 이 바다는 중심부(황해의 중심부)를 기준으로 하여 중국 대륙의 산동반도에서 양가강 하구에 이르는 서부 해안을 가지며 북부에는 발해만의 해안이 있고 동부에는 서해(황해) 특유의 넓 은 조수환경(tidal environment)과 조수해안이 발달한다. 그러나 남쪽으로는 북서태평양과 연결된다. 한국 서해안이 평균 4m 이상의 조차(tidal range)를 나타내는 조간대 조수환경이 며 조간대 해저지형(intertidal morphology)이 전형적인 퇴적층(체)에 의하여 지배되는 여러 가지 특징을 나타낸다. 서해안 조수환경은 네델란드, 독일 또는 지배되는 여러 가지 특징을 나타낸다. 서해안 조수환경은 네델란드 독일 또는 미국의 경우와 같이 연구가 잘되어 세계 적으로 널리 알려진 소위 barrier island system and tidal depositional environments와는 크 게 다른 퇴적과정과 환경이다. 경기도 남양만의 조수 환경의 경우, 조간대 해저지형 요소인 조류로(tidal channel)와 조간대 정규해저(intertidal zone proper)에 관한 동력적 퇴적과정 연 구결과 조간대 특유의 lateral sedimentation 과 vertical sedimentation 2가지 퇴적과정중 후 자의 퇴적과정이 우세한 것으로 밝혀졌고 이러한 퇴적과정의 진행이 매우 안정한 지속성을 가지는 것이 특징이다, 이러한 퇴적과정의 조간대 퇴적물의 쇄설 입자는 약 20% 미만의 모 래(sand) 입자 50~70%의 실트(silt) 와 점토(clay) 입자가 20~30%에 달하는 입자조직 (grain texture)의 퇴적상을 나타낸다. 결과적으로 조간대의 동력적인 조수수괴의 수위(level of tidal water)는 평균 만조선과 평균 저조선으로 한정되며 이것은 퇴적과정과 퇴적작용의 조정(control) 요인으로 조간대 퇴적상의 발달과 분포에 큰 영향을 미친다, 예를들면 남양만 등의 대부분의 서해안 조간대 표층 퇴적상(녁\ulcorner미 sedimentary faci-es)은 만조선에서 간조 선에 가까울수록 조립화현상(coarsening trend)을 나타낸다. 이러한 퇴적상 변화는 저조선에 서 만조선으로의 조간대 지형과 주조수로의 지형.수력학적 특성이 다음과 같기 때문이다. a) a general decrease in width b) a general decrease in depth c) a general decrease in maximum and average current velocities d) a general increase in contents of suspended mud e) a general decrease in grain size of the bottom sand and an increasing abundance of muddy deposits. 우리나라 서해안 조간대 퇴적층(체)의 수직 층서(vertical stratigraphy)는 지난 3여년동안의 수십개의 vibracoring(주상시추)에 의하여 매우 흥미롭고 중요하게 밝혀지고 있는바 이것은 현세(Holocene)와 선현세(preHolocene: 11000 years BP)의 오랜시간 경과에 따른 조수환경 변화의 수직퇴적 과정과 기후 해수면 변화의 현상에 원인이 있다고 해석된다.(박용안 외, 1992-1995)결과적으로 서해안 조수퇴적체(층)의 분지주변(basim margin)진화과정이 밝혀지 고 있다.