• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.3
• /
• pp.246-251
• /
• 2013

Screen printing is commonly used to form the front/back electrodes in silicon solar cell. But it has caused high resistance and low aspect ratio, resulting in decreased conversion efficiency in solar cell. Recently the plating method has been combined with screen-printed c-Si solar cell to reduce the resistance and improve the aspect ratio. In this paper, we investigated the effect of light induced silver plating with screen-printed c-Si solar cells and compared their electrical properties. All wafers were textured, doped, and coated with anti-reflection layer. The metallization process was carried out with screen-printing, followed by co-fired. Then we performed light induced Ag plating by changing the plating time in the range of 20 sec~5min with/without external light. For comparison, we measured the light I-V characteristics and electrode width by optical microscope. During plating, silver ions fill the porous structure established in rapid silver particle sintering during co-firing step, which results in resistance decrease and efficiency improvement. The plating rate was increased in presence of light lamp, resulting in widening the electrode with and reducing the short-circuit current by shadowing loss. With the optimized plating condition, the conversion efficiency of solar cells was increased by 0.4% due to decreased series resistance. Finally we obtained the short-circuit current of 8.66 A, open-circuit voltage of 0.632 V, fill factor of 78.2%, and efficiency of 17.8% on a silicon solar cell.

• Korean Journal of Materials Research
• /
• v.30 no.7
• /
• pp.369-375
• /
• 2020

FDM 3D printing structures have rough surfaces and require post-treatment to improve the properties. Fumigation is a representative technique for removing surface unevenness. Surface treatment by fumigation proceeds by dissolving the surface of the protruding structure using a vaporized solvent. In this study, 3D printed PVB outputs are surface-treated with ethyl-alcohol fumigation. As the fumigation time increases, the surface flattens as ethanol dissolves the mountains on the surface of PVB and the surface valleys are filled with dissolved PVB. Through the fumigation process, the mechanical strength tends to decrease, and deformation rate increases. Ethanol vapor permeates into PVB, widening the distance between chains and resulting in weak bonding strength between chains. In order to confirm the effect of fumigation only, an annealing process is performed at 80 ℃ for 1, 5, 10, 30, and 50 minutes and the results of the fumigation are compared.

• Journal of Chest Surgery
• /
• v.18 no.4
• /
• pp.759-770
• /
• 1985

This study was experimentally undertaken to evaluate the effect of hypothermic oxygenated cardioplegic solution on myocardial protection during prolonged aortic cross clamping under cardiopulmonary bypass. Dogs were divided into two groups control group [received hypothermic unoxygenated cardioplegic solution] and experimental group [received hypothermic oxygenated cardioplegic solution]. Coronary sinus effluent was obtained at once and 30, 60, 90 minutes after cross-clamping for the determination of pH, PCO2,PO2 and lactate level during the infusion of cardioplegic solution and myocardial biopsies were obtained after cessation of 90 minutes of aortic cross-clamping. The results obtained were as follows: 1. There was no significant differences in the pH and PCO2 between the oxygenated and unoxygenated cardioplegic solution but the PO2 of the oxygenated solution was 4 times greater than unoxygenated solution, and also the oxygenated solution had a significantly greater oxygen content [2.020.05 ml 02/min] and had much more oxygen delivery than unoxygenated solution. 2. The myocardial oxygen consumption and the myocardial oxygen extraction in oxygenated group were 1.63 ml 02/100 ml and 67.32% respectively, which was greater than those in unoxygenated group. 3. Regarding to pH and PCO2 of coronary sinus effluent, there was no significant differences between two groups in early period of infusion of cardioplegic solution, but the pH shifted to acidosis from 60 minutes, PCO2 increased from 90 minutes of aortic cross-clamping, and PO2 markedly decreased from 90 minutes of aortic cross-clamping in unoxygenated group. 4. The lactate concentration of coronary sinus effluent revealed relatively normal in both groups, but showed slight increase up to 27.54.56 mg/100 ml at 90 minutes of aortic cross-clamping in unoxygenated group. 5. On electron microscopic study, the ultrastructural integrity of myocardial cells in oxygenated group was well preserved within 90 minutes. Slight swelling and deformity of mitochondria, interfibrillar widening, and disarrangement of myofibrils were observed at 90 minutes after aortic cross-clamping in unoxygenated group. From these results, the use of hypothermic oxygenated cardioplegic solution seemed to be effective and better method for the preservation of ischemic myocardium during the prolonged aortic cross-clamping.

• Journal of Korea Water Resources Association
• /
• v.31 no.3
• /
• pp.337-345
• /
• 1998

DAMBRK-U model is developed for the evaluation of overtopping risk of dam and levee and for the estimation of uncertainty in floodwave simulation. The original algorithm is revised and expanded to include Monte-Carlo analysis to estimate them. The model is tested by applying to hypothetical channels of widening, uniform and narrowing geometry. Larger variation in discharge and water depth are expected at narrower sections of a river. It is calibrated by applying to the Hantan River, where severe damages from Yunchun dam-break and levee overtopping occurred on July, 1996. Overtopping risk of dam is calculated for various discharge conditions for Yunchun-dam, and that of levee is also calculated by comparing levee height with flood level at Hantan recreation area. Simulation results show that the overflow depth of flood level is 1,266~0.782 m and the overflow risk turns out to be 100%.

• Korean Journal of Veterinary Research
• /
• v.35 no.3
• /
• pp.489-496
• /
• 1995

Artemisia messes-schmidiana var viridis(Compositae) has been used for jaundice, hepatitis, diuretic and liver cirrhosis etc. 1-naphthylisothiocyanate(ANIT) has been used as a model compound to study mechanisms of intrahepatic cholestasis in laboratory animals as rat and mouse. The purposes of present study are to examine pharmacological effects of Artemisia messes-schmidiana var viridis water extract(AMWE) on alterations of triacylglycerol, cholesterol, protein, albumin and A/G ratio levels in serum, of histopathological appearances of liver, and that of hepatic microsomal cytochrome P-450 contents. Increased serum triacylglycerol levels by ANIT were significantly decreased with AMWE. However, AMWE posttreatment aggravated ANIT-induced cholesterol increase. Serum total protein and albumin contents, and A/G ratio were decreased in all ANIT-treated groups, and there were increased compared with control by AMWE posttreatment. Hepatic microsomal cytochrome P-450 contents were decreased in either AMWE and ANIT treatment, which greatly increased with AMWE pretreatment. On the other hand, in histological findings, our results shown that ANIT induced increase of lipid droplets and widening of sinusoidal capillary and these phenomena were disappeared with AMWE treatment. In conclusion, AMWE have choleresis effect. Also, AMWE improved lipid metabolism, protection and regeneration of hepatocytes in ANIT-induced cholestasis.

• The Journal of Internal Korean Medicine
• /
• v.22 no.2
• /
• pp.245-250
• /
• 2001

Paraquat is one of the widely used herbicides. But it is fatal, if it is consumed by people. Paraquat poisoning causes acute renal failure, hepatic dysfunction, and progressive respiratory failure. There are no effective antidotes to paraquat. This report is about one case's treatment for acute hepatitis caused by paraquat. The patient was hospitalized in the Department of Internal Medicine, Wonkwang University Oriental Medical Hospital in Chonju. The patient received the following treatments while in an acute stage : Gamdutanggamibang(甘豆湯加味方), which consists of Radix glycyrrhizae(甘草), Semen mungo(綠豆), burned powder of Rhizoma rhei(大黃炒炭末), Succus phyllostachyos(竹瀝), chinese ink(墨汁) and fluid therapy. The patient received Sagunjatanggamibang(四君子湯加味方) while in a chronic stage. The patient improved faster with the above treatments than with the conventional treatment. We hope that this report will help widening the clinical range of oriental medicine, and improve systemic efforts in treating paraquat poisoning cases.

• Parasites, Hosts and Diseases
• /
• v.25 no.2
• /
• pp.110-122
• /
• 1987

The rabbits were infected with Clonorchis sinensis and were treated with praziquantel at the dose of $50{\;}mg/kg{\times}2회{\times}2$ days after 1,2,4,8 weeks and 7 months from the infection. Their livers were observed histopathologically 1, 4 and 12 weeks after treatment. The findings are summarized as below. 1. The changes of the liver in control rabbits were relatively mild until 2 weeks after infection. However, widening and thickening of bile ducts, proliferation of biliary epithelium and periductal fibrosis were moderate after 4 weeks from infection and those changes were severe after 8 weeks and 7 months. Goblet cell metaplasia was found after 8 weeks from infection. 2. The mild changes of 2-week infection group were completely recovered by 4 weeks after the treatment. In the groups of 4 or more weeks after infection, the changes of bile ducts became milder in the degree after the treatment, but were still found 12 weeks after the treatment. As the infection duration was passed, more severe changes were observed after the treatment. In this context, it is concluded that the liver changes of acute clonorchiasis in the early two weeks are reversible by treatment while chronic biliary epithelial changes are irreversible. Therefore, early treatment should be recommended as possible to minimize the remaining histopathological changes of liver in clonorchiasis.

• Restorative Dentistry and Endodontics
• /
• v.23 no.1
• /
• pp.487-501
• /
• 1998

In the case of CAD/CAM ceramic inlay restorations, if isthmus width is widened too much, it may cause fracture of remaining tooth structure or loss of bonding at the luting interface because of excessive displacement of buccal or lingual cusps under occlusal loads. So to clarify the criterior of widening isthmus width, this study was designed to test the tensile bond strength and bond failure mode between dentin and ceramic cemented with luting composite resin cements. Cylindrical ceramic blocks(Vita Cerec Mark II, d=4mm) were bonded to buccal dentin of 40 freshly extracted third molars with 4 luting composite resin cements(group1 : Scotchbond Resin Cement/Scotchbond Multi-Purpose, group2 : Duolink Resin Cement/ All-Bond 2, group3: Bistite Resin Cement/Ceramics Primer, and group4:Superbond C&B). Tensile bond test was done under universal testing machine using bonding and measuring alignment blocks(${\phi}ilo$ & Urn, 1992). After immersion of fractured samples into 1 % methylene blue for 24 hours, failure mode was analysed under stereomicroscope and SEM. Results: The tensile bond strength of goup 1, 2 & 4 was $13.97{\pm}2.90$ MPa, $16.49{\pm}3.90$ MPa and $16.l7{\pm}4.32$ MPa, respectively. There was no statistical differences(p>0.05). But, group 3 showed significantly lower bond stregnth($5.98{\pm}1.l7$ MPa, p<0.05). In almost all samples, adhesive fractures between dentin and resin cements were observed. But, in group 1, 2 & 4, as bond strength increased, cohesive fracture within resin cement was observed simultaneously. And, in group 3, as bond strength decreased, cohesive fracture between hybrid layer and composite resin cement was also observed. Cohesive fracture within dentin and porcelain adhesive fracture were not observed. In conclusion, although adhesive cements were used in CAD/CAM -fabricated ceramic inlay restorations, the conservative priciples of cavity preparation must be obligated.

• Archives of Craniofacial Surgery
• /
• v.14 no.1
• /
• pp.30-35
• /
• 2013

Background: For reconstruction of the mild to moderate medial orbital wall fractures, various surgical approaches have been used. Prior existing W-shaped incision was a direct local approach through a 3 cm incision on the superior medial orbital area with a titanium mesh implant. In this study, the authors modified W-shaped incision and reconstructed the defect with silastic sheet to improve the result and the postoperative scar. Methods: This study included 20 patients who had mild to moderate size of medial wall defect and therefore relatively suitable for reconstruction with silastic sheets from July, 2009 to December, 2011. A modified W-shaped skin incision approximately 1.2 to 1.5 cm in length was made along the superior medial orbital rim from approximately 1 cm medial to the medial canthus to the lower border of the medial eyebrow. The angles of the limbs of the W ranged from 150 to 160 degrees. Results: By using soft flexible silastic sheet, the authors reduced the incision from 3 to 1.5 cm, and by widening the angle of the W limbs, scars were more effectively hided in the relaxed skin tension line. Scar assessment was done with modified patient and observer scar assessment scale and mean score from patients was 2.08 and mean score from observers was 2.12. Conclusion: Although this method will not be suitable for every case, it can be a consistent method to obtain the surgical goal in treatment of mild to moderate blowout fractures of the medial orbital wall.

• Philosophy of Education
• /
• no.39
• /
• pp.191-221
• /
• 2009

The aim of this study is to analyse of elements and structure of consciousness theory in the 1887 Psychology written by John Dewey, and to research its educational implications. Conclusions are as follows: Firstly, consciousness theory articulated in first edition of Dewey's Psychology was influenced by neo-Hegelian G. S. Hall, and then characteristics of its theory was metaphysical and idealistic. But after of researching the work of William James, his approach to consciousness changed surprisingly from idealistic to experimental. His experimental approach and scientific attitude to it influenced the formation and development of advanced theories in his epistemology, axiology and pedagogy. Secondly, the structure of consciousness expressed by Dewey has three forms such as knowledge, feeling and will(or volition). This forms are too dynamic and unitary. Dewey considered cognition, feeling, will to be integral functions of each self. The tripartite functions of self, moreover, are unified in will. In other word, will combines subjective feeling and objective knowledge as one self. Will regulates impulse because it powers some stimulus into activity of self. In this view point, his theory of consciousness differs from traditional theories about consciousness for emphasizing dynamic relations and functions. Thirdly, Dewey's theory of consciousness will give some important implications to educational field. It is necessary to fundamental arguments about conscious conditions of learners as a human. For it is impossible to establish some aim of learning, to organize meaningful contents of learning, and also to create some effective methods of learning without consideration of this conditions. And it is important to construct and organize the contents and methods of learning for widening and deepening of educational experiences. Then consciousness and experiences of learners interact each other, so then they will produce some meaningful results of learning in this process.