• 한국의류산업학회지
• /
• 제15권3호
• /
• pp.444-451
• /
• 2013

This paper surveys the physical properties of aramid and aramid/nylon hybrid air-jet textured yarns(ATY) for protective garments according to wet and dry texturing conditions. Aramid and nylon filaments were used to make two kinds of para-aramid ATY and four kinds of aramid/nylon hybrid ATY with dry and wet treatments. The analyzed physical properties of six specimens (made on the ATY machine) are as follows. The tenacity and initial modulus of aramid and aramid/nylon hybrid ATY decreased with the wetting and breaking strain; however, the yarn linear density of aramid and hybrid ATY increased with wetting treatment. The dry and wet thermal shrinkage of the hybrid ATY increased with wetting. The stability of aramid and hybrid ATY also increased with wetting. The physical properties of core/effect type hybrid ATY showed significantly more change than the core type hybrid ATY and the physical properties of nylon/aramid core/effect hybrid ATY showed significantly more change than the of aramid/nylon core/effect hybrid ATY. A higher bulky and breaking strain of hybrid ATY require ATY processing conditions of nylon on the core part with wetting and aramid on the effect part. ATY processing conditions for nylon and aramid on the core part with wetting are required for a higher tenacity and modulus. ATY processing conditions of nylon and aramid on the core with no wetting are required for a low thermal shrinkage.

• 한국지반공학회논문집
• /
• 제29권12호
• /
• pp.25-34
• /
• 2013

본 논문에서는 계절적 환경변화로 인한 습윤-건조 반복과정에 노출되는 옹벽구조물의 거동에 관한 축소 모형실험 연구 내용을 다루었다. 이를 위해 먼저 습윤-건조 과정을 모사할 수 있는 모형 옹벽 실험 장치를 구축하고 강우강도 및 뒤채움흙의 종류 등을 매개변수로하여 다양한 조건에 대한 실험을 수행하였다. 그 결과 강우로 인한 습윤-건조 반복 과정은 옹벽의 변위를 증가시키고 토압을 증가시키는 등 거동 측면에서 불안정성을 야기시킬 수 있는 인자로 검토되었다. 한편, 전반적으로 첫 번째 습윤-건조 사이클에서 변위가 가장 크게 발생하고 그 이후 습윤 사이클에서의 변위 증가량은 사이클이 진행되면서 감소되는 것으로 관찰되었다. 아울러 이러한 습윤-건조 반복과정의 영향은 뒤채움흙의 종류에 따라 그 정도가 차이나는 것으로 나타났으며 세립분 함유량이 클수록 습윤-건조 반복작용의 영향이 큰 것으로 검토되었다.

• 열처리공학회지
• /
• 제22권1호
• /
• pp.23-26
• /
• 2009

Pt nanotubes with diameter of 200 nm were fabricated by simple and convenient method of Template-Wetting Process. Porous alumina membranes were prepared by 2 step anodic oxidation as the template. To improve wetting properties and lower surface energy, pt solution was mixed with polymer. Polymer was removed completely during annealing. Grain growth process of pt nanotubes during baking and furnace annealing was examined by FE-SEM and XRD.

• 오토저널
• /
• 제15권1호
• /
• pp.67-72
• /
• 1993

Wall wetting phenomenon in the intake port of an MPI engine was investigated with different kinds of injectors by an A/F step response test and analysis was done based on the simple wall wetting model to find out a certain correlation between wall wetting and A/F variations. It was found that (1) At fully warmed condition of 90.deg.C water temperature, around 40-60% of injected fuel was wall wetted, (2) At cold condition of 45.deg.C Water temperature, around 68-80% of injected fuel was wall wetted, and (3) A/F variations during acceleration and deceleration were influenced by the wetting area, the fuel droplet size, and the amount of wall wetting fuel.

• 한국세라믹학회지
• /
• 제19권1호
• /
• pp.24-34
• /
• 1982

The effect of the several variables on wetting of AISIB1113 steel by molten glass was studied by Sessible-drop method. Experimental variables were temperature, firing atmospheres, Fe2O3 addition to the sealing glass and steel surface conditions. The degree of wetting in terms of contact angles between molten glass and metal tested at different test conditions was analyzed by using Young's equation. The results showed that contact angles in H2 atmosphere in the glass metal systems were high but in N2 atmosphere, were small for studied glass metal systems. Especially, when the glass drop was in contact with oxidized steel in N2 atmosphere, The best adherence with contact angle of approximately 9°was obtained. In the case of Fe2O3 addition in glass contact angles subtantially increased due to the increase of surface tension of glass. Wetting phenomena were also discussed under the basis of these experimental results.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2004년도 임시총회 및 추계학술발표회
• /
• pp.89-92
• /
• 2004

The influence of a single fracture intersection on density-driven immiscible flow is compared between wetting (water into air) and nonwetting (Trichloroethylene into water) flows. At low supply rates, the intersection acted as a hysteretic gate to pulsed flow of the wetting phase, but had minimal influence on nonwetting phase flow. For both cases, increasing the supply rate led to the formation of continuous fluid tendrils that crossed the intersection without interruption. The wetting experiment returned to pulsed flow as the supply rate was decreased, while the nonwetting experiment maintained a continuous flow structure. Results suggest a fundamental difference between wetting and nonwetting phase flows in fracture network.

• 한국세라믹학회지
• /
• 제44권5호
• /
• pp.141-143
• /
• 2007

Nanotubes and microtubes of ferroelectric lead zirconate titanate (PZT) were synthesized by means of a simple and convenient process called a template-wetting process. Nanoporous alumina and macroporous Si were used as template materials to fabricate the corresponding tubes. For the improvement of the wetting properties of the wetting solution, the PZT solution was mixed with a polymer. The polymer was removed completely during annealing. The grain growth processes of the PZT nanotubes during baking and furnace annealing were examined by means of field emission electron microscope (FE-SEM) and X-ray diffractometry (XRD).

• Nano
• /
• 제13권10호
• /
• pp.1850120.1-1850120.9
• /
• 2018

Two-dimensional poly(dimethylsiloxane) (PDMS) films with wavy patterns were studied in order to investigate reversible and irreversible wetting effects. Pre-strained, surface oxidized layers of PDMS were used to form relieved wavy geometries, on which hydrophobic functionalization was carried out in order to produce irreversible wetting effects. Wavy-patterned PDMS films showed time-dependent reversible wetting effects. The degree of surface wettability could be tuned by the choice of wavy groove geometries. And the groove geometries were controlled via $O_2$ plasma treatment and mechanical pre-straining. The pre-strained, buckled PDMS films were applied to the fabrication of hydrophobic polystyrene nano-patterns using colloidal self-assembly, where the colloids were arrayed in two-dimensional way. The wavy polystyrene films were found to be more hydrophobic relative to flat polystyrene films. The grooving methodology used in this study could be applied to enhancing the hydrophobicity of other types of polymeric thin films, eliminating the need for chemical treatment.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2019년도 추계 학술논문 발표대회
• /
• pp.153-154
• /
• 2019

In this study, the fluidity and compressive strength of lightweight mortar using recycling water for pre-wetting of artificial lightweight aggregate were compared and analyzed to maximize the utilization of the recycling water, which is a by-product of the Ready-Mixed Concrete industry. For this purpose, the pre-wetting water was replaced with recycling water at the ratio of 0, 2.5, 5, 7.5 and 10%.

• Nuclear Engineering and Technology
• /
• 제56권2호
• /
• pp.437-443
• /
• 2024

The development and testing of inspection equipment is necessary for the safe deployment of advanced nuclear reactors. One proposed advanced reactor design is Westinghouse's lead-cooled fast reactor (LFR). In this paper, the process of achieving adequate wetting for an ultrasonic under-lead viewing system is discussed and results presented. Such a device would be used for inspection in the molten lead core during reactor outages. Wider tests into the wetting of various materials in molten lead at microscale were performed using electron microscopy. The possible mechanisms and kinetics for materials wetting in lead, particularly stainless steel and nickel, are proposed and discussed.