• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.45 no.6
• /
• pp.1-9
• /
• 2013

For the manufacture of linerboard with 100% KOCC, we tried to increase the solid content of wet web by employing GCC (grounded calcium carbonate) in the fiber furnish to save drying energy. Three different diameters of GCC, namely, 5, 10, and $35{\mu}m$, were used. To complement the strength loss by the addition of GCC, cationic starch and refining treatment were tried. It was found that the addition of $10-35{\mu}m$ dia. GCC to KOCC for $180g/m^2$ basis weight sheets increased the solid content of the furnish about 1-1.5% with better bulk and drainage properties. The loss of strength properties were compensated by the application of cationic starch and/or refining process to the KOCC furnish. The dia. of GCC of $35{\mu}m$ was, however, too large to make smooth surface of the sample sheet. So, the optimization process was required before implementing the results to the mill by selecting proper diameter and shape of the calcium carbonate.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.38 no.4 s.117
• /
• pp.17-23
• /
• 2006

Paper has fibers and fines network structure and it is strongly affected by interface bond-ing between fibers. Paper structural properties can be determined depending on the inter-fiber bonding. Fines play an important role in Campbell and consolidation effect through wet pressing and drying operations. The fines are essential for the formation of bonds between fibers and for the improvement of strength properties of papers. Since the fines are components of the pulp, there are always two factors to be considered: the quality and quantity of the fines. The quality of fines might be a potential variable to give a more accurate picture of the papermaking potential of the pulp. The object of this study is to investigate the effect of different types of pulp fines on the properties of paper and to access the potential of fines for controlling the bulk of paper. Refined Sw-BKP, Hw-BKP and BCTMP fines were used to investigate the fines effect. Wet-web strength, breaking length, scattering coefficient, and hydrodynamic specific volume, and drying shrinkage were measured. According to the results, chemical and morphological compositions of fines do not strongly affect to wet-web forming by their similar Campbell effect, but strongly affect to drying operation which forms hydrogen bonding among fiber-fines-fiber matrixes. Paper bulk should be controlled by the extent of hydrogen bonding between fibers during drying operation.

• Korean Journal of Food Science and Technology
• /
• v.10 no.1
• /
• pp.1-7
• /
• 1978

The wet soybean residue, a byproduct of soymilk industry having potential food value has been tried to dehydrate for the purpose of storage. The total solid of the byproduct was composed of 28.9% protein, 13.6% fat, 4.4% ash and 53.0% carbohydrates. The original water content of 593%(dry-weight basis) was reduced to 378% by pressing mechanically. The sufficient pressure and time for the pressing were found to be 0.5M/T and 5minutes, respectively. The partially dehydrated soybean residue was formed into pellets of 3mm in diameter and 10mm in length. By applying hot air on the thin layer of pellets the moisture could be further reduced to the level of 10% which is equivalent to that of the commercial wheat flour. No significant color deterioration in the product was observed if the hot air dehydration procedure was within the limit of 95 minutes at $120^{\circ}C$ under the air flow velocity of 160 feet per minute.

• Korean Journal of Materials Research
• /
• v.14 no.10
• /
• pp.743-748
• /
• 2004

Modified Ni/YSZ cermets for high temperature electrolysis were synthesized by the direct ball milling of Ni and YSZ powder. The ball milling was carried out in dry process and in ethanol with varying milling time. While the dry-milling decreased the average size from 65 to $80{\mu}m$, the wet-milling decreased the average size down to $10{\mu}m$. In addition, very fine particles less than $0.1{\mu}m$ were observed in the wet-milling condition. The subsequent process of cold-pressing and sintering at $900^{\circ}C$ for 2 h did not affect the particle size of dry-milled powder. The electrical conductivity of the dry-milled Ni/YSZ cermet showed the value of $5{\times}10^{2}\;S/cm$ and this value was increased to $1.4{\times}10^{4}\;S/cm$ after the sintering at $900^{\circ}C$ for 2 h.

• Transactions of the Korean hydrogen and new energy society
• /
• v.16 no.2
• /
• pp.150-158
• /
• 2005

Added ratio of 8YSZ powder and organic compounds (solvent, plasticizer, dispersant, binder) properly. It manufactured electrolysis membrane by wet process that make slurry and dry process that do not use organic compounds. In the case of wet process, harmony combination and method of organic compound are an importance element in slurry manufacture. This slurry did calcine at temperature of 140$^{\circ}C$ in Furnace and manufactured electrolyte disk by Dry pressing method. Like this, manufacturing disk sintered at temperature of $1300^{\circ}C,\;1400^{\circ},\;1500^{\circ}C$ in Furnace and completed electrolysis membrane. Confirmed change of crystal structure and decision form through analysis of density, SEM, XRD according to change of sintering temperature, and considered relation with ion conductivity.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.20 no.2
• /
• pp.215-222
• /
• 2002

As the GPS signals propagate from the GPS satellites to the receivers on the ground, they are delayed by the atmosphere. The tropospheric delay consists of two components. The hydrostatic (or "dry") component that is dependent on the dry air gasses in the atmosphere and accounts for approximately 90% of the delay. And the "wet" component that depends on the moisture content of the atmosphere and accounts for the remaining effect of the delay. The Zenith Hydrostatic Delay (ZHD) can be calculated from the local surface pressure. The Total Zenith Delay (TZD) will be estimated and the wet component extracted later. Integrated water Vapor (IWV) gives the total amount of water vapor that a signal from the zenith direction would encounter. Precipitable Water Vapor (PWV) is the IWV scaled by the density of water. The quality of this PWV has been verified by comparison with radiosonde data(at Osan). We processed data for JULY 2 and JULY 14, 1999 from four stations(Cheju, Kwangju, Suwon, Daegu). We found the coincidence between PWV of the estimations using GPS and PWV of pressing the radiosonde data. The average of the difference between PWV using GPS and PWV using radiosonde was 3.77 mm(Std. ＝ $\pm$0.013 mm) and 2.70 mm(Std. = $\pm$0.0011 mm) at Suwon & Kwangju.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.1
• /
• pp.17-23
• /
• 2009

The influence of different forming elements on the local paper structure and the related paper properties was investigated in this study. Specifically, a conventional papermaking foil system and a velocity induced drainage (VID) system were compared. The study involved the analysis of the product samples obtained from the commercial machine trials. The paper samples produced with VID forming systems showed better formation. The deterministic patter in the local structural profile map of the Foil samples indicated the structure of foil samples was more supple after forming process and then easier to be marked by various fabrics such as wet pressing fabric. The higher bulk was observed in the VID samples, which resulted in higher scattering coefficient, lower ZDT strength, and higher bending stiffness.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2011.04a
• /
• pp.217-226
• /
• 2011

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.2
• /
• pp.15-19
• /
• 1996

To utilize the waste materials and develope wood adhesive from isolated bloods of slaughtered cow and pig and also to prevent water pollution, simple and rapid method of isolation and purification of plasma proteins from pig bloods with trichloroacetic acid(TCA) treatment was developed. Adding of TCA-precipitated blood powder to the phenol formaldehyde resin(PF) improved dry and wet strength of plywood and resulted in fast hot pressing times.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.417-422
• /
• 2006

On trends of 'well-being', heat recovery ventilators(HRV) are recently installed in high rise buildings. HRV is not energy saving instrument but ventilating one. But many people have not been aware of the accurate fact. In this study, performances of HRV are tested under foreign and domestic standards. Especially air-tightness is measured three times by using gas concentration method and pressing equipment. Wet effective ventilating air volume is acquired by solving gas concentration equations. After research air-tightness and effective ventilating air volume must be more focused on than heat transfer efficiency to select the optimal HRV. Heat transfer efficiency must be adjusted by air-tightness results.