• Applied Science and Convergence Technology
• /
• 제23권5호
• /
• pp.254-260
• /
• 2014

Organic solar cells have attracted extensive attention as a promising approach for cost-effective photovoltaic devices. However, organic solar cell has disadvantage of low power conversion efficiency in comparison with other type of solar cell, due to the recombination ratio of hole and electron is too large in the active layer. Thus we have change the surface structure of PEDOT:PSS layers to improve the current density by colloidal lithography method using various-size of polystyrene sphere. The two types of coating method were applied to fabricate the different pattern shape and height, such as spin coating and drop casting. Using the organic solvent, we easily eliminate the PS sphere and could make the varied pattern shapes by controlling the wet etching time. Also we have measured the electrical properties of patterned PEDOT:PSS film to check whether it is suitable for organic photovoltaics.

• 센서학회지
• /
• 제14권5호
• /
• pp.357-361
• /
• 2005

Low-stress silicon nitride (LSN) thin films with embedded metal line have been developed as free standing structures to keep microspheres in proper locations and localized heat source for application to a chip-based sensor array for the simultaneous and near-real-time detection of multiple analytes in solution. The LSN film has been utilized as a structural material as well as a hard mask layer for wet anisotropic etching of silicon. The LSN was deposited by LPCVD (Low Pressure Chemical Vapor Deposition) process by varing the ratio of source gas flows. The residual stress of the LSN film was measured by laser curvature method. The residual stress of the LSN film is 6 times lower than that of the stoichiometric silicon nitride film. The test results showed that not only the LSN film but also the stack of LSN layers with embedded metal line could stand without notable deflection.

• 한국정밀공학회지
• /
• 제17권8호
• /
• pp.41-45
• /
• 2000

This paper provides a new concept of the controllable micro damper using MR(Magneto Rheological)fluids. The damper is composed of four layers which are fabricated by wet etching. The Process of the fabrication is explained and the change of damping property is experimentally shown. Since the damping force is controllable by the applied magnetic field the vibration can be effectively absorbed.

• 한국전기전자재료학회논문지
• /
• 제25권1호
• /
• pp.58-61
• /
• 2012

In our report a relatively simple process for fast nano-texturing of p-type(100) CZ- silicon surface using silver catalyzed wet chemical etching in aqueous hydrofluoric acid (HF) and hydrogen peroxide solution($H_2O_2$) at room temperature. The wafers were saw-damaged by NaOH(6 wt%) at $60^{\circ}C$ for 150s. To obtain a nano-structured black surface, a thin layer of silver with thickness of 1 - 10 nm was deposited on the surfaces by evaporation system. After this process the samples were etched in HF : $H_2O_2$ : $H_2O$ = 1:5:10 at room temperature for 80s - 220s. Due to the local catalytic of the Ag clusters, this treatment results in the nano-scale texturing on the surface. This resulted in average reflectance values less than 9% after the silver on the surface of the wafers were removed.

• 한국광학회지
• /
• 제16권2호
• /
• pp.113-120
• /
• 2005

LCD-BLU(liquid crystal device-back light unit)에 사용되는 도광판의 미세 산란패턴을 만드는 새로운 방법으로서, 실리콘 웨이퍼의 비등방 식각에 의해 자연적으로 형성되는 3차원 결정면 구조를 이용하는 방법을 제안하였다. 실리콘 3차원 결정면을 갖는 도광판과 프리즘 시트의 원판을 설계 및 제작하였고, casting 공정을 통해 PDMS 재질로 복제된 도광판을 제작하여 특성을 분석하였다. 측정 결과, 기존 인쇄형 도광판에 비해 실리콘피라미드 패턴의 도광판이 $10\%$ 증가된 정면 휘도 효율을 가질 수 있음을 실험적으로 검증하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.86-86
• /
• 2010

Micro- and nanoscale texturing and control of surface energy have been considered for superhydrophobicity on polymer and silicon. However these surfaces have been reported to be difficult to meet the robustness and transparency requirements for further applications, from self cleaning windows to biochip technology. Here we provided a novel method to fabricate a nearly superhydrophobic soda-lime glass using two-step method. The first step involved wet etching process to fabricate micro-sale patterns on soda-lime glass. The second step involved application of $SiO_x$-incorporated DLC to generate high intrinsic contact angle on the surface using chemical vapor deposition (CVD) process. To investigate the effect of surface roughness, we used both positive and negative micro-scale patterns on soda-limeglass, which is relatively hard for surface texturing in comparison to quartz or Pyrex glasses due to the presence of impurities, but cheaper. For all samples we tested the static wetting angle and transparency before and after 100 cycles of wear test using woolen steel. The surface morphology is observed using optical and scanning electron microscope (SEM). The results shows that negative patterns had a greater wear resistance while the hydrophobicity was best achieved using positive patterns having static contact angle up to 140 deg. with about 80% transparency. The overall experiment shows that positive patterns at etching time of 1 min shows the optimum transparency and hydrophobicity. The optimization of micro-scale pattern to achieve a robust, transparent, superhydrophobic soda-lime glass will be further investigated in the future works.

• 한국재료학회지
• /
• 제11권2호
• /
• pp.71-75
• /
• 2001

The reaction stability of nickel with side-wall materials of SiO$_2$ and Si$_3$N$_4$ on p-type 4"(100) Si substrate were investigated. Ni on 1300 $\AA$ thick SiO$_2$ and 500 $\AA$ - thick Si$_3$N$_4$ were deposited. Then the samples were annealed at 400, 500, 750 and 100$0^{\circ}C$ for 30min, and the residual Ni layer was removed by a wet process. The interface reaction stability was probed by AES depth Profiling. No reaction was observed at the Ni/SiO$_2$ and Ni/Si$_3$N$_4$, interfaces at 400 and 50$0^{\circ}C$. At 75$0^{\circ}C$, no reaction occurred at Ni/SiO$_2$ interface, while $NiO_x$ and Si$_3$N$_4$ interdiffused at Ni/Si$_3$N$_4$ interface. At 100$0^{\circ}C$, Ni layers on SiO$_2$ and Si$_3$N$_4$ oxidized into $NiO_x$ and then $NiO_x$ interacted with side-wall materials. Once $NiO_x$ was formed, it was not removed in wet etching process and easily diffused into sidewall materials, which could lead to bridge effect of gate-source/drain.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 추계학술발표대회
• /
• pp.50.1-50.1
• /
• 2009

Transparent conductive oxides (TCOs) play an important role in thin-film solar cells in terms of low cost and performance improvement. Al-doped ZnO (AZO) is a very promising material for thin-film solar cellfabrication because of the wide availability of its constituent raw materials and its low cost. In this study, AZO films were prepared by low pressurechemical vapor deposition (LPCVD) using trimethylaluminum (TMA), diethylzinc(DEZ), and water vapor. In order to improve the absorbance of light, atypical surface texturing method is wet etching of front electrode using chemical solution. Alternatively, LPCVD can create a rough surface during deposition. This "self-texturing" is a very useful technique, which can eliminate additional chemical texturing process. The introduction of a TMA doping source has a strong influence on resistivity and the diffusion of light in a wide wavelength range.The haze factor of AZO up to a value of 43 % at 600 nm was achieved without an additional surface texturing process by simple TMA doping. The use of AZO TCO resulted in energy conversion efficiencies of 7.7 % when it was applied to thep-i-n a-Si:H thin film solar cell, which was comparable to commercially available fluorine doped tin oxide ($SnO_2$:F).

• 전자공학회논문지A
• /
• 제29A권4호
• /
• pp.38-48
• /
• 1992

OEIC(Optoelectronic Integrated Circuit)'s can be integrated horizontally or vertically. Horizontal integration approach is, however, more immune to parasitic and more universally applicable. In this paper, a structural modeling, fabrication and characterization of PIN photodiodes which can be used in the horizontal integration are performed. For device modeling, we build a transmission line model from 2-D device simulation, from which lumped model parameters are extracted. The speed limits of the PIN photodiodes can also be calculated under various structural conditions from the model. Thus optimum design of horizontally integrated PIN photodiodes for high speed operation are possible. Such InGaAs/InP PIN photodiodes for long-wavelength communications are fabricated using pit etch, epi growth, planarization, diffusion and metallization processes. Planarization process using both RIE and wet etching and diffusion process using evaporated Zn$_{3}P_{2}$ film are developed. Characterization of the fabricated devices is performed through C-V and I-V measurements. At a reserve bias of 10V, the dark current is less than 5nA and capacitance is about 0.4pF. The calculated bandwidth using the measured series resistance and capacitance is about 4.23GHz.

• 마이크로전자및패키징학회지
• /
• 제6권4호
• /
• pp.15-22
• /
• 1999

일반적으로 빌드업 다층 인쇄회로기판은 에칭, 도금등의 습식공정에 의해 제작이 이루어지므로 많은 장비와 많은 시간이 필요하게 된다. 이러한 습식공정은 양산에는 적합하지만 개발단계에서는 그리 적합하지 않은 방법이다. 본 연구에서는 스크린 인쇄기술을 도입하여 빌드업 다층 인쇄회로기판을 제작하여 보았다. 절연성 재료로는 광경화성수지 또는 열경화성수지를 사용하였으며 전도성 재료로는 전도성 페이스트를 사용하였다. 층간의 전기적 연결을 담당하는 비아와 회로를 형성하기 위해 스크린 인쇄공정을 통해 전도성 페이스트를 인쇄 하였다. 이러한 방법을 통해 제품의 개발 단계에서 기존의 빌드업 다층 인쇄회로기판 제작 공정과 비교하여 좀더 효율적인 방법을 제시하였다.