• 항공우주시스템공학회지
• /
• 제16권1호
• /
• pp.12-16
• /
• 2022

유도 용접은 비접촉식으로 깨끗하고 빠른 공정으로 현재 주목받고 있다. 하지만 열가소성 수지는 전자기장에 영향을 받지 않기 때문에 유도 용접은 서셉터(Susceptor)라는 발열체가 필요하다. 고품질 접합을 목표로 연구가 진행되고 있지만, 결국 발열체라는 이물질이 들어가기 때문에 기준이 필요하다. 시편의 제작과 시험은 ASTM D5868에 근거하여 진행된다. 본 논문에서 평가 기준은 용접된 접합면의 상태와 기공률, 전단강도로 총 3가지를 근거로 판단할 것을 제안한다. 용접되는 접착면은 용융되고 냉각되면서 고형화가 되기 때문에 급격한 온도 변화는 기공을 발생시킬 수 있다. 또한 가열이 균일하지 않다면 원하는 성능을 기대하기 힘들다. PA6 (CF 30%) 엔지니어링 플라스틱을 이용하여 서셉터 제작과 유도 용접 그리고 성능 검증으로 진행하였다.

• International Journal of Korean Welding Society
• /
• 제3권2호
• /
• pp.29-39
• /
• 2003

The durability and reliability of thermal barrier coatings (TBCs) play an important role in the service reliability, availability and maintainability (RAM) of hot­section components in advanced turbine engines for aero and utility applications. Photostimulated luminescence spectroscopy (PSLS) and electrochemical impedance spectroscopy (EIS) are being concurrently developed as complimentary non­destructive evaluation (NDE) techniques for quality control and life­remain assessment of TBCs. This paper overviews the governing principles and applications of the luminescence and the impedance examined in the light of residual stress, phase constituents and resistance (or capacitance) in TBC constituents including the thermally grown oxide (TGO) scale. Results from NDE by PSLS and EIS are discussed and related to the microstructural development during high temperature thermal cycling, examined by using a variety of microscopic techniques including focused ion beam (FIB) in­situ lift­out (INLO), transmission and scanning transmission electron microscopy (TEM and STEM).

• Journal of Welding and Joining
• /
• 제27권6호
• /
• pp.74-79
• /
• 2009

Titanium and titanium alloy can be reproduced immediately even if oxide films($TiO_2$) break apart in sea water. Therefore, since titanium demonstrates large specific strength and outstanding resistance to stress corrosion cracking, crevice corrosion, pitting and microbiologically influenced corrosion in sea water environment, it has been widely applied to heat exchanger for ships. In particular, with excellent elongation, pure titanium may be deemed as optimal material for production of heat exchanger plate which is used with wrinkles formed for efficient heat exchange. Conventional plate type heat exchanger prevented leakage of liquid through insertion of gasket between plates and mechanical tightening by bolts and nuts, but in high temperature and high pressure environment, gasket deterioration and leakage occur, so heat exchanger for LPG re-liquefaction device etc do not use gasket but weld heat exchanger plate for use. On the other hand, since welded plate cannot be separated, it is important to obtain high quality reliable welds. In addition, for better workability and production performance, lasers that can obtain weldment with large aspect ratio and demonstrate fast welding speed even in atmospheric condition not in vacuum condition are used in producing products. So far, 1st report and 2nd report compared and analyzed embrittlement degrees by bead colors of weldment through quantitative analysis of oxygen and nitrogen and measurement of hardness as fundamental experiment for the evaluation of titanium laser welding, and evaluated the welding performance and mechanical properties of butt welding. This study welded specimens in various conditions by using laser and GTA welding machine to apply edge welding to heat exchanger, and evaluated the mechanical strength through tensile stress test. As a result of tensile test, laser weldment demonstrated tensile strength 4 times higher than GTA welds, and porosity could be controlled by increasing and decreasing slope of laser power at overlap area.

• 한국음향학회지
• /
• 제38권3호
• /
• pp.334-339
• /
• 2019

차량 점용접 부위에서 BSR(Buzz, Squeak, Rattle) 소음 발생 가능성을 국부 진동을 사용하여 비파괴적으로 추정하는 진동기반 계측법을 제시한다. 용접부에 부착된 구조물에 의한 점용점 부위의 국부적인 진동을 유발하고 진동전달 특성을 파악한다. 관측된 진동 특성으로부터 국부 구조의 굽힘강성값을 도출하였다. 강성값의 변화로부터 점용접의 상태 강건성을 파악하였다. 제시되는 방법의 검증을 위해 부분적으로 용접품질이 변화된 시편을 제작하였다. 제작된 시편에서 계측된 진동 특성을 분석하였다. 용접 강건성에 의해 변화하는 특정 주파수 대역을 파악하였다. 구조별, 위치별 계측을 통해 제시된 방법으로 분별이 가능한지 검증하였다. 국부 진동 평가방법은 구조물의 용접 강건성을 생산 현장에서 파악하게 하는 평가방법으로써 BSR발생 가능성을 저감하기위한 생산 품질 확보에 사용될 수 있다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제17권4호
• /
• pp.100-106
• /
• 1993

A study on optimizing the friction welding of copper(C1100) to aluminium(A1050) for developing the electrical sleeve was experimentally carried out and also on real-time nondestructive evaluation of the friction weld quality (strength) was accomplished by acoustic emission technique. The results obtained are summarized as the following ; 1) The heating upset $U_1$(mm) or total upset U(mm) tends to increase according to the increase of heating time $t_1$(sec). The relations between $U_1$ and $t_1$ or U and $t_1$are computed as follows when n=2000rpm, $P_1$=4, $P_2$=8kgf/$mm^2$, and $t_2$=6sec. U=1.6$e^{0.39t_1}$ $U_1$=3.65$e^{0.25t_1}$. 2) It was notified that the proper welding conditions by considering on both strength with more than 100% joint effieciency and toughness are heating time of 1.5-2.25 sec under n=200rpm, $P_1$=4, $P_2$=8kgf/$mm^2$, $t_2$=6sec. 3) It was confirmed that both AE total counts(N, counts) and the weld tensile strength (${\sigma}$, kgf/$mm^2$) of the welded joints increase as the increase of heating time, respectively, the relations between N and $t_1$, ${\sigma}$ and $t_1$ are computed from data points by regression analysis using the least square method as follows in case of the above proper condition ; N=50108+23917(ln $t_1$)${\sigma}$$=11.85+2.06(ln $t_1$). 4) Both empirical and calcularated equations of relationship between .sigma. and N are very coincident with a high reliability, as the following in case of the above proper welding condition ; Calculated : ${\sigma}$=0.00008N+7.5 Empirical :${\sigma}$= $8.17e^{0.0000072N}$. 5) It was confirmed that the real-time nondestructive weld strength evaluation for friction welding of copper(C1100) to aluminium(A1050) could be possible by acoustic emission technique.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.68-68
• /
• 2009

최근에 자동차 차체 경량화를 목적으로 개발된 고장력강의 용접품질 향상을 위해 인버터 DC 점용접기가 많이 사용되어지고 있다. 본 연구에서는 국내에서 개발된 인버터 DC 용접기를 사용하여 자동차용 590MPa 고장력 냉연강판(CR, SPFC 590RA)과 아연 도금 강판 (GA- EZFFC 590RA)의 용접품질을 평가하였다. 용접에 사용된 기본 조건은 인장 전단 시험을 통하여 결정하였으며, 동저항, 압흔 자국과 너겟 지름, 인장강도와의 관계를 통계적 방법으로 분석하였으며, 이를 활용하여 고장력 강판의 동저항과 압흔 자국에 따라 너겟 지름과 용접강도를 예측하는 비파괴적 용접 품질 평가 방법을 제시하였다.

• 한국자동차공학회논문집
• /
• 제16권5호
• /
• pp.8-14
• /
• 2008

For nondestructive inspection of electron beam (EB) welding part in automotive power transmission assembly, a pulse-echo ultrasonic testing apparatus in water immersion has been applied using the ultrasonic waves with a frequency of 10MHz. However various problems have appeared during the ultrasonic inspection, which led to some significant mistakes in automatic quality evaluation of the welding parts. Experimental study showed that the state of water couplant medium containing some amount of contaminants, rusts and anti-corrosion agents had considerable influences on the reduction of ultrasonic amplitudes during wave propagation. The amplitude reduction depending on the coupling medium state could bring about some mis-diagnoses for defects in the welding parts. The results proposed that for a reliable inspection of defects in welds the state of water medium should be kept in about 15 volume fractions (vol.%) of anti-corrosion agents and in minimized contaminants.

• 한국산학기술학회논문지
• /
• 제13권4호
• /
• pp.1460-1465
• /
• 2012

본 연구에서는 소방배관용 아연도금 강관을 용접하기 위하여 반자동 가스메탈아크용접장치를 개발하고 최적 용접 조건을 확립하고 용접성을 조사하기 위해 보호가스, 전압을 변화시켜 용접시험을 수행하였다. Ar 가스에 $O_2$를 첨가함으로써 미려한 비드외관과 기공률이 감소되었다. 반자동 용접부는 기계적 강도와 용접이음효율이 수동용접부에 비해 약 1.8배 우수하였으며 수압시험에 의해 건전성이 확인되었다. 본 연구에서 개발된 반자동용접장치로 비숙련자도 강관용접이 가능하며 용접결함이 적고 용접생산성을 증대시킬 수 있을 것으로 기대된다.

• 한국정밀공학회지
• /
• 제23권11호
• /
• pp.68-77
• /
• 2006

Nowadays, the increasing global competition forces automobile manufacturer to increase quality and to reduce the cost and time for manufacturing planning. To solve these problems, automobile manufacturers try to apply digital manufacturing technologies. In this paper, a concept of method for planning the digital assembly system is proposed. Based on the requirements of assembly tasks obtained through product analysis, the function and sequence modeling for assembly process is executed using the IDEF0 and UML model. For implementation of digital assembly system, the selected components are modeled by using 3D CAD tools. According to the system configuration strategy, lots of the alternative solutions for the assembly system are generated. Finally, the optimal assembly system is chosen by the evaluation of the alternative solutions with TOPSIS(Technique for Order Preference by Similarity to Ideal Solution) method. According to proposed procedure, digital laser welding system is implemented in DELMIA.

• 동력기계공학회지
• /
• 제10권1호
• /
• pp.77-82
• /
• 2006

In this study, dissimilar friction welding were produced using 15mm diameter solid bar in chrome molybedenum steel(SCM440) to carbon steel(S45C) to investigate their mechanical properties and the relationship between the weld parameters and the nondestructive coefficients, such as AE counts and ultrasonic attenuation coefficient. The main friction welding parameters were selected to endure good quality welds on the basis of visual examination, tensile tests, Vickers hardness surveys of the bond of area and heat affected zone. The specimens were tested as-welded and post weld heat treated(PWHT). The tensile strength of the friction welded steel bars was increased up to 100％ of the S45C base metal under the condition of all heating time. The ductility of PWHT specimens is higher than as-welded.