• Journal of Welding and Joining
• /
• v.7 no.4
• /
• pp.22-29
• /
• 1989

In this paper weld distortion both in butt and fillet welds by flux cored arc welding has been investigated by changing welding parameters such as heat input and plate thickness, and the weld distortion was expressed as a function of welding parameters adopting the inherent strain theory as proposed by Watanabe and Satoh in 1961. As results of the research it is proposed that transverse shrinkage in root pass butt welds in proportional to ln[(Q/t_-tan.theta.] where Q is heat input(cal/mm), t is plate thickness(mm), and 2.theta. is groove angle(degree), and angular distortion .phi.(radian) in one pass of fillet welds has the following relationship: .phi..var.(Q/ $t^{1.5}$)$^{3}$exp[-(Q/ $t^{1.5}$ )$^{2}$3/] These equations provide us with basic tools to predict the amount of weld distortion in welded structures.

• Journal of Welding and Joining
• /
• v.6 no.1
• /
• pp.21-27
• /
• 1988

This paper describes weldability of dissimilar metal plates with YAG laser for the use of a small-size electronic spring parts. Effects of welding conditions, combination of plates, thickness of upper plate are examined in relation to welding strength and microstructure of welded region. The obtained results are summarized as follows. Welding defects such as cavity and crack showed a tendency to easily occur in the case where 1) pulse duration is short, 2) laser power is high, 3) PBS plate with high thermal diffusivity is used for lower plate. Among these defects, the occurrence of cavity cased a drop of welding strength. This results from the reduction of welding area between upper and lower plates. In SK-5/SUS304 plates (thickness: 0.2/0.4mm/, welding strength was the highest in welding conditions: laser power is 30J/pulse, pulse duration 9ms, amount of defocus +2mm.

• Journal of Welding and Joining
• /
• v.16 no.3
• /
• pp.44-54
• /
• 1998

In this study a new arc sensor algorithm for automatic weld seam tracking was proposed, which uses the relative welding current variation according to the tip-to-workpiece distance in GMA welding. Since the new developed arc sensor algorithm is not sensitive to unstable factors of arc signal, the system is expected to get rid of the problems of already existing arc sensor system which include the difficulty of modeling the process for various welding conditions and limitation of application to thick plate welding. Thus the system is applicable not only to thick plate welding but also to thin plate welding. To implement the new arc sensor algorithm the system parameters which include sampling time, averaging range, weighting factor of moving averaging, basic compensation time, and basic compensation distance were determined by experimental analysis. Consequently this system has shown the successful tracking capability for the various welding conditions.

• Journal of Welding and Joining
• /
• v.32 no.6
• /
• pp.70-74
• /
• 2014

On this study, we researched the in-process monitoring during fiber laser welding as well as on the first paper. On the previous/formal study, we analyzed the change of emission signal on thin plate welding. On this study, however, we analyzed RMS and FFT with emission signals in laser welding on lap joint and butt joint of 8mm-thick 316L stainless steel. As the result, the movement of specific frequency peak was observed according to welding speed changes. Furthermore, frequency peak as a result of FFT on the thick plate welding are much clearer than on the thin plate welding. Therefore, it is expected that the welding parameter changes can be predicted in case of applying FFT to in-process monitoring.

• Journal of Welding and Joining
• /
• v.4 no.2
• /
• pp.30-39
• /
• 1986

In manufacturing of pipe walls for boiler units, distortion can result in pipe-web-pipe joints from the nonuniform expansion and contraction of the weld metal and the adjacent base metal during heating and cooling cycle of the welding process. In this study, the stresses and strains during longitudinal welding of the plate-to-pipe joint were investigated. Using the method of successive elastic solution, longitudinal stresses and strains during and after welding were calculated from the information of temperature distributions obtained by Rosenthal's equations. In order to confirm the validity of the numerical results, the temperature and residual stress distributions were measured and compared with the calculated results. In spite of some assumptions, the one-dimensional analytical results of residual stresses were in fairly good agreement with the experimental ones. The residual stresses due to welding of plate-to-pipe joints are tensile near the weld line and compressive in the base metal as in the welding of plates. the amount and distribution of residual stresses were deeply dependent on the heat input ratio of the plate and pipe.

• Journal of Power System Engineering
• /
• v.15 no.3
• /
• pp.58-64
• /
• 2011

As well known, the friction stir welding is a novel welding process which is a solid state welding process for sheet or plate using the friction stir phenomenon. This paper describes the effect of welding condition such as the rotation speed and the travelling speed during the friction stir welding process on the micro Virkers hardness and the microstructure of friction stir welded joints in AI-7075-T651 plate. From those investigations, the highest hardness of stir zone was observed at the welding condition of SO-3. The microstructures of the friction stir welded joints was not dependent on the welding conditions, but in the SO-4 specimen, the friction stir welding defect like tunnel shape was found in stir zone.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.5
• /
• pp.31-38
• /
• 2016

This study proposes an optimal design for a robotic welding system for a high-strength steel armor plate. In order to identify the welding defect parameters, we analyzed the 4M (man, machine, materials, method) characteristics diagram, as well as a cause and effect matrix, to improve the productivity and quality of welding defects. From these analyses, we designed optimal welding conditions and carried out welding tests -- such as mechanical testing and macro structure tests - with positive results. We determined that it was possible to obtain a quality similar to manual welding with our robotic welding system. In the future, we expect that the system will be used as inspiration for future welding system designs.

• Journal of Welding and Joining
• /
• v.15 no.1
• /
• pp.55-65
• /
• 1997

The stress intensity factor has been calculated for the cracked plate subjected to remote normal stress and reinforced with a plate by symmetric spot welding. The solution was based on displacement compatibility condition between the cracked sheet and the reinforcement plate. It is shown that the results from the derived equation for stress intensity factor were agreed with previous solutions. The reinforcement effect gets better as a joining spot is closer to the crack tip and the other joining spots become nearer to the crack surface.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.5
• /
• pp.504-508
• /
• 2007

In the case of thin plate blocks, buckling deformation due to longitudinal shrinkage is the most important weld-induced deformation. This paper is concerned with developing the formula to predict the longitudinal shrinkage due to welding, in which mechanical tension effect in welding direction is accounted for. For this purpose, bead on plate welding test has been carried out for the 27 thin plate specimens with varying welding conditions and magnitude of tensile load. Empirical formula of predicting the longitudinal shrinkage has been derived based on the results of welding test, in which effect of mechanical tension is included. The derived formula can be usefully used in predicting the level of tensile load to reduce the longitudinal shrinkage.

• Journal of Welding and Joining
• /
• v.20 no.5
• /
• pp.113-119
• /
• 2002

To prevent problems caused by welding deformation, preparation in the design stage is necessary. Countermeasures in the design stage is also the most cost-effective method. In this study, to give designers information on the welding deformation, a system to visualize the welding deformation is developed. The model to visualize the deformation is the stiffened plate common in steel structures. To increase computational efficiency, theoretical solutions to calculate the deformation of plate and stiffener are used instead of numerical analysis. Also, to secure accuracy, experiments to estimate bending moment causing welding deformations are performed. A computer program written with Visual C++ is developed for interactive data input, calculation of welding deformation and display of deformed shape. Designers can change the design in the early stage after checking the deformed shape by this system.