• Journal of the Korean Applied Science and Technology
• /
• v.2 no.2
• /
• pp.47-53
• /
• 1985

Correlation among the wax-pigment composites which is base vehicles for the crepas was investigated in terms of fadeness. The base wax synthesized and pigments are compounded with petroleum lubricant and exposed under carbon arc individually. The yellowing phenomenon was appeared on the reference papers coated with the spindle oil which was then exposed. The papers were again extracted with distilled water and pH of them were ranged between 6.2-6.5. Color difference from Adam-Nickerson equation, ${\vartriangle}E$ of base wax is 0.15 and that of spindle oil are varied from 0.66 to 15.62. Since the main components of the petroleum lubricant are aromatic hydrocarbons which have absorptions characteric of UV ranging from 240 to 280 nm, fadeness characteristics of the composites are largely depend upon the change of molecular structure of spindle oil by absorbing UV. Thus the spindle oil having the following physical properties has the better resistance of fadness and is recommended to use in compounding the base wax-pigment composites: ${\cdot}$ main component: paraffinic hydrocarbon ${\cdot}$ pour point: below - $15^{\circ}C$ ${\cdot}$ UV absorption characteristics: ${\lambda}max.$ : 268-290nm ${\cdot}$ absorbancy: below 0.1(0.03ml of sample/50ml of $CHCl_3$)

• Journal of the Korean Applied Science and Technology
• /
• v.21 no.4
• /
• pp.335-344
• /
• 2004

In this work, the properties as polishing wax for automobile of O/W type microemulsion containing wax, liquid paraffine and quaternaryammonium salt was investigated. The microemulsions were prepared at $96{\sim}97^{\circ}C$ by the phase inversion method, and polyoxyethylene(20) sorbitan monooleate (POE(20)SMO) and distearyl dimethyl ammonium chloride(D.D.A.C) as the emulsifiers were used. The mean particle size of the rnicroemulsions was about 7${\pm}$0.5nm and as the properties of polishing wax, gloss increased degree, water resistant gloss degree, initial and final contact angle after water resistance were tested. The result was that the value of water resistantance and contact angle were decreased with increasing amount of POE(20)SMO and D.D.A.C., while the gloss degree values did not affected. And the rnicroemulsion blended with mono ethylene glycol(MEG) of 5${\sim}$15wt% showed smaller particle size and more stable particle size distribution than without MEG. Finally, this microemulsion showed more excellent values of gloss degree, the water resistant gloss degree and contact angle, than two kinds of commercial polishing wax for automobile.

• Korean Journal of Food Science and Technology
• /
• v.10 no.4
• /
• pp.409-414
• /
• 1978

The total amount of lipid content in the mullet roe is 20.5%, and iodine value and unsaponifiable matters content are 118 and 38.7%, respectively. The lipid composition of the muscle, roe and liver of the mullet, Mugil cephalus, shows differences. Triglyceride, wax esters, and free fatty acids are mainly contained in the lipids of the muscle, roe and liver, respectively. The mullet roe lipids are mainly composed of 59.1% of wax esters with a trace of sterol esters, 26.9% of polar lipids with pigments, 9.0% of triglyceride plus a trace of free fatty alcohols and fatty acids, and 3.0% of sterol contaminated with a trace of fatty alcohols. The major fatty acids of wax esters are C16 : 0, 47.5%, C18 : 1, 23.0%, C16 : 3, 6.5%, C20 : 5, 4.0%, those of triglyceride are C16 : 1, 25.1%, C18: 1, 16.7%, C16 : 0, 16.3%, C22 : 1, 7.9%, C18 : 0, 5.5%, C22 : 6, 4.4%, and those of polar lipids are C16 : 0, 35.0%, C18 : 1, 24.7%, C16 : 1, 6.1%, C20 : 5, 5.3%, C22 : 6, 4.2%. The major alcohols of wax esters are 51.0% of cetyl alcohol, 18.2% of palmitoleyl alcohol, and 10.7% of oleyl alcohol, and considerable amounts of odd-numbered alcohols such as C15 : 0, C15 : 1, C17 : 0, C17 : 1 and C19 : 1 are also found.

• Applied Microscopy
• /
• v.42 no.1
• /
• pp.43-48
• /
• 2012

This study shows that ceresin wax, candellila wax and microcrystalline wax mixed together with liquid paraffin oil to produce lipsticks (LS-1, LS-2) and capric/caprylic triglyceride oil added to produce lipsticks (LS-3, LS-4). After each type of lipsticks were molded, LS-1 and LS-3 was put into a cooling chamber ($5^{\circ}C$). LS-2 and LS-4 was put into a cooling chamber ($5^{\circ}C$) for 18 hours and kept in an incubator ($45^{\circ}C$) for 5 hours and put again into a cool chamber ($5^{\circ}C$). After that, the wax's three dimensional network structure was observed under scanning electron microscopy. Regardless of the kind of oil, the LS-1 and LS-3 wax structure had more distinct shape than the lipstick wax structure of LS-2 and LS-4. Also, regardless of the kind of wax, the three dimensional network structure was modified as the storage temperature increased. As a result, the lipstick's molding temperature increased, the wax's structure size also increased and the shape irregularly modified. This modification causes sweating phenomenon which affected lipstick's surface rheological property.

• The Journal of Korean Society for Radiation Therapy
• /
• v.31 no.1
• /
• pp.75-81
• /
• 2019

Purpose: Helmet type bolus for 3D printer is being manufactured because of the disadvantages of Bolus materials when photon beam is used for the treatment of scalp malignancy. However, PLA, which is a used material, has a higher density than a tissue equivalent material and inconveniences occur when the patient wears PLA. In this study, we try to treat malignant scalp tumors by using M3 wax helmet with 3D printer. Methods and materials: For the modeling of the helmet type M3 wax, the head phantom was photographed by CT, which was acquired with a DICOM file. The part for helmet on the scalp was made with Helmet contour. The M3 Wax helmet was made by dissolving paraffin wax, mixing magnesium oxide and calcium carbonate, solidifying it in a PLA 3D helmet, and then eliminated PLA 3D Helmet of the surface. The treatment plan was based on Intensity-Modulated Radiation Therapy (IMRT) of 10 Portals, and the therapeutic dose was 200 cGy, using Analytical Anisotropic Algorithm (AAA) of Eclipse. Then, the dose was verified by using EBT3 film and Mosfet (Metal Oxide Semiconductor Field Effect Transistor: USA), and the IMRT plan was measured 3 times in 3 parts by reproducing the phantom of the head human model under the same condition with the CT simulation room. Results: The Hounsfield unit (HU) of the bolus measured by CT was $52{\pm}37.1$. The dose of TPS was 186.6 cGy, 193.2 cGy and 190.6 cGy at the M3 Wax bolus measurement points of A, B and C, and the dose measured three times at Mostet was $179.66{\pm}2.62cGy$, $184.33{\pm}1.24cGy$ and $195.33{\pm}1.69cGy$. And the error rates were -3.71 %, -4.59 %, and 2.48 %. The dose measured with EBT3 film was $182.00{\pm}1.63cGy$, $193.66{\pm}2.05cGy$ and $196{\pm}2.16cGy$. The error rates were -2.46 %, 0.23 % and 2.83 %. Conclusions: The thickness of the M3 wax bolus was 2 cm, which could help the treatment plan to be established by easily lowering the dose of the brain part. The maximum error rate of the scalp surface dose was measured within 5 % and generally within 3 %, even in the A, B, C measurements of dosimeters of EBT3 film and Mosfet in the treatment dose verification. The making period of M3 wax bolus is shorter, cheaper than that of 3D printer, can be reused and is very useful for the treatment of scalp malignancies as human tissue equivalent material. Therefore, we think that the use of casting type M3 wax bolus, which will complement the making period and cost of high capacity Bolus and Compensator in 3D printer, will increase later.

• Applied Chemistry for Engineering
• /
• v.8 no.5
• /
• pp.844-852
• /
• 1997

In the polymerization of ethylene to produce crystalline polyethylene wax using the homogeneous titanium-based catalyst, the effects of various parameters such as catalyst, temperature, pressure, comonomer and time on the performance of catalyst and the properties of polyethylene wax were investigated. The properties of polyethylene wax obtained were characterized in terms of molecular weight, molecular weight distribution, crystallinity, density and morphology. Among the polymerization features with a series of mixed cocatalyst systems of $(C_2H_5)_3Al$, $(i-C_4H_9)_3Al$, $(C_2H_5)_2AlCl$ and $(C_2H_5)_3Al_2Cl_3$, it turned out that the combination of $(C_2H_5)_3Al$ and $(C_2H_5)_3Al_2Cl_3$ was more effective than any other combination. It was noted that the activity of catalyst and the properties of polyethylene wax were affected by the polymerization parameters, i.e. time, temperature and hydrogen partial pressure. The various kinds of crystalline polyethylene wax could be obtained by careful control of these parameters. Also we could obtain low density polyethylene wax which has density down to 0.91 g/cc by use of 1-butene as a comonomer.

• The Korean Journal of Food And Nutrition
• /
• v.14 no.1
• /
• pp.52-58
• /
• 2001

The 7.5% wax gourd-added mash composed of 7.5% brown rice. 1.5% malt. 3% red ginseng and 6% ethanol solution, and mash which 7.5% wax gourd was not added were fermented as vinegar and produced acetic acid, with the use of Acetobacter aceti 3281, at 25$\^{C}$ for 150 days. As the result, vinegar of no added-wax gourd was shown containing 3.3 % total sugar, 1.5% reducing sugar, 11.5 absorbance at 280nm, 2.7$\mu$M/ml amino acid, and 0.5 % ethanol, 3.0 pH, 4.59% acidity, 5.2% organic acid. The 7.5% wax gourd-added vinegar showed 2.3% of total sugar, 1.1% reducing sugar, 10.8 absorbance at 280nm, 2.1 $\mu$ M/ml amino acid, 1.2% ethanol, 3.1 pH, 4.61% acidity, 4.9% organic acid. In preference test of 5-points in full, red ginseng vinegar showed 3.86, and wax gourd-red ginseng vinegar 3.66.

• Solar Energy
• /
• v.12 no.3
• /
• pp.37-46
• /
• 1992

An experimental study was carried out to investigate the performance of a latent heat storage system using paraffin wax as the phase change material. A thermosyphon was employed to transfer heat from the hot ethylene glycol flowing across the evaporator section of the thermosyphon into the wax. In order to increase the effective thermal conductivity of wax, layers of copper wire mesh were immersed in the wax. Experiments were run for volume ratios of 2%, 3%, and 4%, varying mass flow rate of ethylene glycol in each case. Some of the important results are as follows : (1) The wire mesh enhanced the conductive hea transfer and thus, helped even out the temperature distribution in the wax : (2) The increase of the number of layers of wire mesh increased the conduction. However, it also resulted in increasing the resistance to the convective motion of liquefied wax : and (3) There is an optimal number of layers of wire mesh, maximizing the performance of the storage system, which occurred at a volume ratio of $3{\sim}4%$ in the present study.

• Journal of Conservation Science
• /
• v.26 no.4
• /
• pp.437-443
• /
• 2010

The influence of noxious corrosive gas, which is the product of fossil fuel, and the acidic descent material, which becomes the reason for such reaction, on wax which protects the cultural assets, and the habitat factor were researched. It could be viewed that corrosion occurred rapidly due to the acidic descent material, which have the long staying on the material, rather than harmful corrosive gas. Also, it could be figured out that such corrosion began from whitening phenomenon of coated wax. As the acidity increased, more whitening phenomenon occurred, and eventually, it could be found out that whitening effect began due to the acidic descent material, corrosive gas and various 0.1 M acid solution, which lead to the exposure of internal metal, and corrosion occurred. The wax with the greatest resistance to the acidity due to its least changing aspect seemed to be Renaissance wax, except sulfuric acid.

• Korean Journal of Food Science and Technology
• /
• v.36 no.5
• /
• pp.795-799
• /
• 2004

Noodles were prepared by adding 25, 50, 75, and 100% wax gourd juice to wheat flour, and effects of added wax gourd juice on dough rheology and cooking and noodle qualities were examined. Initial pasting temperature, and peak and final viscosities increased with addition of wax gourd juice. Water absorption and dough weakness, and cooked weight, moisture absorption, cooked volume, and cooking loss of noodleincreased, but dough development time and dough stability decreased with increase in wax gourd juice content. Hardness, cohesiveness, and gumminess of cooked noodles increased significantly with increase in war gourd juice content. Sensory evaluation results reveal noodles containing 25 and 50% wax gourd juices have higher qualities than other types.