• 대한조선학회논문집
• /
• 제58권6호
• /
• pp.339-347
• /
• 2021

Piston type wave makers or flap type wave makers are usually adopted as a wave maker which disturbing the fluid domain with sinusoidal motion. Recently hybrid wave maker which could be operated as not only piston type and/or flap type but also swing type wave maker have been devised by utilizing the link mechanism. The wave board of hybrid wave maker has been devised to be independently controlled by the horizontal actuators on upper and lower end of the wave board. The wave board could operate as a flap type wave board when the lower hinge is in a stationary condition and the upper hinge is operated with sinusoidal motion. On the contrary, the swing type wave board could be obtained by the lower hinge is activated and the upper hinge is in a stationary condition. When both end of the wave board is activated in a synchronized condition, the wave board motion become piston motion. In addition the hybrid wave maker could enhance the piston motion with flap motion or swing motion by selecting control parameters. Various wave board motion of hybrid wave maker and relevant wave form have measured on the wave board and departed location. It is appeared that the novel hybrid wave maker could be utilized for the improvement of wave qualities in experiments.

• 한국해양공학회지
• /
• 제17권5호
• /
• pp.19-24
• /
• 2003

The question of wave source identification in a wave maker problem is the primary objective of the this paper. With the observed wave elevation, the existence of the wave maker velocity is discussed with the help of the mathematical theory of inverse problems. Utilizing the property of the Strum-Liouville system and compactness, the uniqueness and the ill-posedness(in the sense of stability) for the identification are proved.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.263-267
• /
• 2004

This paper presents a comparative study on numerical and wave-maker generated waves. The wave-makers employed to carry out the experiments have mathematical forms. The linear and quadratic models were tested. When it comes numerical analysis, the authors used the FLUENT which is widely used commercial code. Only two dimensional cases were considered. The experiments were done in a small wave flume. The waves were generated for various frequencies to examine the characteristics of the water waves. The comparison of the numerical and wave-maker generated waves were made.

• 한국해양공학회지
• /
• 제33권6호
• /
• pp.504-509
• /
• 2019

The wave-generation performance of a piston-type wave maker was analyzed using the numerical wave tank technique, and the numerical results were compared with theoretical solutions. A two-dimensional frequency domain analysis was conducted based on the Rankine panel method. Various parameters were used to examine the wave-generation performance, such as the width and gap of the wave board. The effects of the thickness of the wave board and of the gap from the bottom of the tank were evaluated. The difference in the amplitude of the generated wave between the analytical solution and the numerical result was examined, and its causes were addressed due to the gap flow between the bottom of the tank and the wave board. This parametric analysis can be utilized to design an optimum wave make parametric analysis to design an optimum wave maker that can generate waves with amplitudes that can be predicted accurately.

• Journal of Ship and Ocean Technology
• /
• 제6권4호
• /
• pp.13-18
• /
• 2002

Active control has been partly applied to suppress the re-reflecting waves in wave basin with plunger-type wave maker to obtain desirable waves. This limitation comes from the non-confirmable theoretical background to the control algorithm. This paper proposes control logic to overcome this drawback, based on the impulse response function for propagating waves between control input and the wave height. The performances have been verified as reasonable in practical application by comparing with the propagating wave components in numerical wave basin, using wave decomposition method. Moreover, the control logic can also give useful wave-absorbing performance after cessation of wave generation.

• Journal of Ship and Ocean Technology
• /
• 제7권1호
• /
• pp.13-18
• /
• 2003

The control performances for active re-reflecting wave control suggested in the previous paper have been verified in cases of regular and irregular waves in a real two dimensional wave basin. For regular waves, the control performances are investigated in terms of reflection coefficients, expected amplitudes of propagating waves and wave absorbing capabilities after cessation of wave generation, compared with those of no-control cases. For irregular waves similar verification procedures were adopted. Though there are certain constraints due to the geometrical non-linearity of wave maker and certain nonlinear characteristics due to the near field and gravity waves these experiments show that the control logic could be useful in realizing re-reflecting wave control in conditions of real wave basin.

• 한국해안·해양공학회논문집
• /
• 제21권2호
• /
• pp.182-190
• /
• 2009

Lin and Liu(1999)는 VOF기법을 도입한 RANS 방정식 모형을 이용하여 목표 파형을 조파할 수 있도록 연속방정식의 질량 원천항을 이용하는 내부조파기법을 제안하였다. 이로부터 외부조파에 의한 영역 내 재반사 문제가 해결되어 RANS 방정식 모형을 이용한 파랑수치실험이 수행되어 발표되어 왔다. 본 연구에서는 RANS 방정식 모형의 운동량 원천항을 이용한 내부조파기법을 사용하여 목표 파형을 조파할 수 있도록 하였다. FLUENT의 사용자 정의함수를 이용하여 두 조파방법에 대해 수치실험하고 비교하였다. 그리고 조파기법의 적용성을 살펴 보기 위해 Luth et al.(1994)의 수리실험을 수치모의하고 그 결과를 비교하였으며, 수심방향 변화를 보이는 수치 모의 결과들을 제시하고 고찰하였다.

• 한국해양공학회지
• /
• 제23권6호
• /
• pp.12-16
• /
• 2009

In this study, the wave profiles and kinematics of highly nonlinear waves at various water depths were calculated using a 2D fully nonlinear Numerical Wave Tank (NWT). The NWT was developed based on the Boundary Element Method (BEM) with the potential theory and the mixed Eulerian-Lagrangian (MEL) time marching scheme by 4th-order Runge-Kutta time integration. The spatial variation of intermediate-depth waves along the direction of wave propagation was caused by the unintended generation of 2nd-order free waves, which were originally investigated both theoretically and experimentally by Goda (1998). These free waves were induced by the mismatch between the linear motion of wave maker and nonlinear displacement of water particles adjacent to the maker. When the 2nd-order wave maker motion was applied, the spatial modulation of the waves caused by the free waves was not observed. The respective magnitudes of the nonlinear wave components for various water depths were compared. It was found that the high-order wave components greatly increase as the water depth decreases. The wave kinematics at various locations were calculated and compared with the linear and the Stokes 2nd-order theories.

• Journal of Ship and Ocean Technology
• /
• 제4권1호
• /
• pp.28-36
• /
• 2000

Numerical simulation based on the superposition of ring waves generated by the linear periodic source distributions for the plunger type wave maker was accomplished. The characteristics of directional spreading function were investigated. Mirror images are also introduced to consider reflections of side-wall together with the reflection coefficient to account for the imperfect reflection from the real side wall in the long experimental towing tank. Unexpected spurious waves, resulting from the combined effect of finite breadth of segmented wave maker, wavelength and main wave maker, wavelength and main wave propagating direction, were observed in the line source method and also in the analysis of the directivity. The influence of spurious waves to the directional spreading function was also investigated.

• 수산해양교육연구
• /
• 제27권5호
• /
• pp.1303-1309
• /
• 2015

The behavior and flow characteristics of the floating wave energy converter were analyzed by using CFD in this study. The average significant wave height was confirmed as 0.5~2.0m from the Korean coastal sea area. This study was carried out by selecting a range of 1.0~1.6m in the wave height to simulate the operations of realistic wave energy converter system. The principle of a piston wave maker was applied in order to produce periodic wave. The behavior of the wave energy converter and the state of the wave overtopping according to the generated periodic wave were confirmed through the unsteady three-dimensional flow analysis. It was found that the wave overtopping rate according to the generated periodic wave was in range of the 11.6~30.0 kg/s.