• Nuclear Engineering and Technology
• /
• v.50 no.6
• /
• pp.971-980
• /
• 2018

Using the concept of quasi-static decomposition and using three-noded isoparametric locking-free element, this article presents a formulation of the finite element method for Timoshenko beam subjected to spatially different time-dependent motions at supports. To verify the validity of the formulation, three fixed-hinged beams excited by the real seismic motions are examined; one is a slender beam, another is a stocky one, and the other is an intermediate one. The numerical results of time histories of motions of the three beams are compared with corresponding analytical solutions. The internal loads such as bending moment and shearing force at a specific time are also compared with analytic solutions. These comparisons show good agreements. The comparisons between static components of the internal loads and the corresponding total internal loads show that the static components predominate in the stocky beam, whereas the dynamic components predominate in the slender one. Thus, the total internal loads of the stocky beam, which is governed by static components, can be predicted simply by static analysis. Careful numerical experiments indicate that the fundamental frequency of a beam can be used as a parameter identifying such a stocky beam.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.4
• /
• pp.329-332
• /
• 2020

A back-electromotive force (back-EMF) estimator for a permanent magnet synchronous motor (PMSM) uses the three-phase voltage references of a current controller to estimate rotor position. However, owing to voltage drops caused by the nonlinear characteristics of switches and passive components, the actual voltage in the motor and the three-phase voltage reference may not match. This study proposes a sensorless control method using a sine-wave output filter applied between the motor drive system and PMSM. The precise voltage in the motor can be measured with the sine-wave output filter and applied to the input of the estimator. Moreover, given that the voltage in the motor can be measured precisely at extremely low speeds, the stable operation range of the back-EMF estimator can be secured. Experimental results show that the proposed sensorless control method has stable operation at extremely low speeds compared with conventional sensorless control.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.109-116
• /
• 2004

Bent-axis piston pump have been commonly used in hydraulic systems because of high pressure level, best efficiency, low shear force on pistons and low operating costs. The other side, they have a few demerits like that they have the relatively high number of moving parts and more discharge pressure ripples. Especially, the discharge pressure ripples bring about vibrations and noises in hydraulic system components such as connecting pipes and control valves, so that these deteriorate the stability and accuracy of the systems. Therefore, the hydraulic systems having the bent-axis piston pump require the methods to reduce the discharge pressure ripples. So, the purpose of this paper is to reduce the discharge pressure ripples by the phase interference of pressure wave and to develope the analysis model of the pumps to predict the discharge pressure ripples. In this paper, the analysis model of the bent-axis piston pump was developed using the AMESim software, and the reliability of that was verified by the comparison with the experimental results. The hydraulic pipeline with a parallel line was used as the method to generate the phase interference of pressure wave. the dynamics characteristics of the hydraulic pipeline with a parallel line were analyzed by a transfer matrix method. the usefulness of the phase interference of pressure wave was investigated through the experiment and simulation. The results from the experiment and simulation said that the phase interference of pressure wave by the hydraulic pipeline with a parallel line could reduce the discharge pressure wave of the pump well. The analysis model of the bent-axis piston pump developed in this paper and the method of the phase interference by the hydraulic pipeline with a parallel line are expected to be helpful to achieve the design of the pump and to reduce the discharge pressure wave of the pump effectively.

• Journal of the Society of Naval Architects of Korea
• /
• v.52 no.6
• /
• pp.485-493
• /
• 2015

Planing hull form is widely used as a high speed vessel hull. There is a problem of the planing hull not solved yet. The problem is that the planing hull has very large vertical acceleration and large heave and pitch motions. As one method for overcoming this problem, there is "wave-piercing hull". Before the motion in waves is investigated, the resistance and running attitude must be investigated. In this paper, the running attitude and resistance of two wave-piercing hulls are investigated by model tests. Model test results show that the wave-piercing hulls have large trim angle and sinkage at the high speed, so additional model tests are conducted by using the hull appended by stern interceptor that is very thin plate to increase the hydrodynamic pressure at the attached location. The results are compared with other planing hulls and the resistance components and the hydrodynamic force are discussed. From the model test results, it can be known that the stern interceptor is the effective appendage for the reduction of the resistance and trim angle of wave-piercing hull.

• Journal of the Korean Society for Railway
• /
• v.19 no.1
• /
• pp.54-66
• /
• 2016

In this study, the absorbing boundary condition was adopted to prevent elastic wave propagation due to abrupt load condition changes in moving force analysis. It was proven to be effective in reducing inappropriate noise components. Furthermore, to verify whether fixed point excitation in a laboratory test can simulate train movement effectively, the results of dynamic analysis for fixed point excitation and moving force conditions were analyzed. The dynamic stability of an asphalt track structure under a KTX train condition was also studied. Additionally, the dynamic safety of asphalt tracks was verified by comparing the results of a moving force analysis under a KTX train load and a quasi-static analysis under the design standard Korean train load.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.2
• /
• pp.247-258
• /
• 2014

To evaluate the influence of the external force components on the littoral currents in the Gusipo beach, Jeonbuk, West Coast of Korea where a wide tidal sand flat developed, a coupled hydrodynamic model considered real time tidal currents and wave-induced currents was constructed in which the EFDC for tides and tidal currents, the SWAN for waves and the SHORECIRC for wave-induced currents were used as the hindcasting models. A series of field observations for tides, tidal currents and incident waves were carried out and especially to observe the littoral currents in the tidal sand flat, the GPS mounted and light weight drogues were used. Also wind data were collected from the adjacent weather station. To analyze the littoral current components, the numerical drogue tracking results considered real time winds, tides and waves were compared with the field drogue data. The drift speed of numerical drogues was reproduced as the range of 68.0~105.2% compared with the field data and the velocity error of main direction component showed a good result as -16.7~10.0%. As a result, in the mild slope tidal flat including wide surf zone, the tides and winds were the major affection component of the littoral currents, on the other hand, the wave-induced currents seemed the minor component when the incident wave heights were relatively small.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.2
• /
• pp.217-224
• /
• 2014

We have developed the novel device that can extract energy from ocean waves utilizing the heaving motion of a floating mass. The major components of the energy converter are: a floater, a counterweight, a cable, a driving pulley, two idler pulleys, a ratchet, and a generator. The device generates power through the tension force in the cable and the weight difference between the floater and the counterweight. When the system is at static free condition, the tension in the cable is equal to the weight of the counterweight which is minimum. Therefore it is desirable to keep the counterweight lighter than the floater. However, experiments show that during the rise of the water level, the torque generated by weight of the counterweight is insufficient to rotate the driving pulley which causes the cable on the floater side to slack. The proposed application of the tension pulley rectifies these problems by preventing the cable from becoming slack when the water level rises. In this paper, the dynamics model is modified to incorporate the dynamics of the tension pulley. This has been achieved by first writing the dynamical equations for the tension pulley and the energy converter separately and combining them later. This paper investigates numerically the effect of the tension pulley on various physical quantities such as the cable tension, the floater displacement, and the floater velocity. Results obtained indicate that this application is successful in suppressing large fluctuations of the cable tension.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.250-253
• /
• 2002

The operation of surface and edge finishing is the last and essential process of parts machining, because a product is completed as an assembly. Therefore, the quality of the finished parts has a direct effect upon the performance of the product. Especially, the edge quality depending on the burr control process is very important. A number of deburring processes have been developed for macro burrs such as barreling, brushing, chemical methods, etc. However, micro burr removal when piercing a very thin plate is very difficult, because this badly deteriorates the surface quality of the processed part. When ultrasonic wave is propagated in liquids, it forms an infinitude of micro bubbles. These bubbles generate extremely strong force, which removes micro burrs. In ultrasonic micro deburring, the problem is that burrs are not removed completely, because only components of the explosive force directly act on the burrs, which is not enough. An attempt was made to remove the burrs using ultrasonic vibration in water with SiC as an abrasive agent. Because of the abrasive, smoother edges have been achieved. There are many control parameters in ultrasonic deburring such as abrasive size, ultrasonic frequency and amplitude, distance between tool and workpiece, tilt angle of workpiece etc. This study focuses on how distance and tilt angle influence deburring effect. A number of experiments for these parameters have been carried out, and then the effect of each parameter analyzed.

• Journal of Ocean Engineering and Technology
• /
• v.29 no.3
• /
• pp.217-223
• /
• 2015

In order to predict the motions of a planing hull in waves, it is necessary to accurately estimate the force components acting on the hull such as the hydrodynamic force, buoyancy, and friction, as well as the wave exciting force. In particular, based on strip theory, hydrodynamic forces can be estimated by the summation of the forces acting on each cross-section of the hull. A non-linear strip method for planing hulls was mathematically developed by Zarnick, and his formula has been used to predict the vertical motions of prismatic planing hulls in regular waves. In this study, several improvements were added to Zarnick's formula to predict the vertical motions of warped planing hulls. Based on calm water model test results, the buoyancy force and moment correction coefficients were modified. Further improvements were made in the pile-up correction. Pile-up correction factors were changed according to variations of the deadrise angles using the results found in previous research. Using the same hull form, captive model tests were carried out in other recent research, and the results were compared with the present calculation results. The comparison showed reasonably good agreements between the model tests and present calculations.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.4
• /
• pp.287-295
• /
• 2012

Hydrodynamic performance of a movable submerged breakwater was analyzed using energy dissipation model. Based on two-dimensional boundary element method the equation of motion including a viscous dissipation term proportional to velocity squared was solved by Newton-Raphson method. Energy dissipation coefficients as well as reflection and transmission coefficients of a submerged flat plate were calculated with various plate lengths and thickness. Both real and imaginary components of body displacement and forces were used to solve the motion of breakwater accurately. The effect of the magnitude of dissipation coefficient on the body displacement was evaluated. The results from the potential theory with no dissipation term were found to be an overestimate in resonance frequency.