• The Korean Journal of Mycology
• /
• v.30 no.2
• /
• pp.99-103
• /
• 2002

The suitable sterilization conditions in pot cultivation of varieties of Chunchunutari-2-ho and Suhannutari-1-ho Pleurotus ostreatus were investigated. The substrate formulations for the cultivation consisted of 40% poplar sawdust, 40% waste cotton and 20% beet pulp (PWB), and 40% poplar sawdust, 40% cotton seed hull and 20% beet pulp (PCB). The increase in the sterilization temperature caused decrease in the pH of the substrate. The moisture content of PWB substrate increased by 1.8%, but that of PCB substrate decreased by 4.1 % after low temperature sterilization ($12hr\;at\;60^{\circ}C$). However, a little change in the sterilization at higher temperature ($6hr\;at\;100^{\circ}C\;and\;90min\;at\;121^{\circ}C$) did not alter the moisture content of both substrate appreciably. The duration of mycelial growth was longest and its density was lowest in low temperature sterilization ($12hr\;at\;60^{\circ}C$). The high pressure sterilization ($90min\;at\;121^{\circ}C$) of PCB substrate produced high yield (236.6 g/pot) and the highest biological efficiency (96.6%) for Chunchunutari-2-ho. On the contrary the high temperatures sterilization ($6hr\;at\;100^{\circ}C$) of PCB substrate resulted in the yield of 259.1 g/pot with the biological efficiency 94.9% for Suhannutari-2-ho.

• Journal of the Korean Society of Systems Engineering
• /
• v.17 no.1
• /
• pp.85-96
• /
• 2021

Radioactive mixed waste (RMW) means waste mixed with radioactive substances and hazardous substances. In Korea, there are definitions and disposal restrictions on RMW in the Nuclear Safety Management Act, but it is difficult to apply because the contents are insufficient, so this paper proposed applicable management standards. The main RMW generated from nuclear power plants is waste oil, waste asbestos, PCB, and waste fluorescent liquid, and their radiation characteristics are mostly at very low levels and some are estimated at low levels. In addition to nuclear power plants, RMW also occurs in research institutes, industries, and hospitals. The acceptance criteria of all disposal facilities in the world basically prohibit disposal of RMW unless the hazardous substances of RMW are removed or mitigated below the standard value. Cases in Korea, the United States, Japan and Europe were reviewed to propose the RMW management standards in Korea. With reference to the results of the above review, this paper clearly defined RMW and proposed detailed management standards for the separation, storage, treatment and disposal of hazardous substances by applying the Waste Control Act. It also mentioned legislation of management standards, regulatory methods, and acceptance criteria of disposal facility operator.

• Analytical Science and Technology
• /
• v.19 no.3
• /
• pp.263-271
• /
• 2006

The levels of total PCBs, Co-PCBs and PCDD/Fs in the transformer insulation oil samples obtained using GC/ECD and HRGC/HRMS were ranged from N.D. to 77.3 ppm, from 0.0863 to 2.49 ppm and from N.D. to 0.00241 ppm, respectively. In terms of WHO-TEQ values, Co-PCBs and PCDD/Fs were ranged from 23.3 to 600 pgTEQ/g and from N.D. to 128 pgTEQ/g, respectively (${\Sigma}Co$-PCBs+PCDD/Fs concentration was calculated 24.4~728 pgTEQ/g). Although, the contribution of PCDD/Fs was below 12% in total TEQ concentration, it is suggested contamination of PCDD/Fs in transformer insulation oils. Among 10 samples, 4 samples showed higher concentration than 2 ppm (specific waste criterion of Korea) and Aroclor 1242, 1248, 1254 and 1260 was detected in samples as a single or mixture of Aroclor. It was shown reliable relationship between concentration of Co-PCBs and those of PCDD/Fs (p<0.003), however, was not shown between production year of transformer and concentration of PCBs. The distribution pattern of Co-PCB congeners showed that the ratios of mono-ortho substituted congeners were higher than non-ortho substituted congeners. Among that, PCB-118 congener was predominant. In addition, the OCDD congener was predominated in PCDD/Fs congeners as above 53%. Moreover, the congener pattern of Co-PCBs was similar to that of Aroclor as well as ambient air, which suggested that PCBs volatilization from transformer insulation oil affected the pattern of Co-PCBs in ambient air.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.165-170
• /
• 2001

The main purpose of this study is to generate a fine copper oxide powder of high purity, with a compact structure and a uniform particle size by a spray pyrolysis process. The raw material is a waste copper chloride solution formed in the manufacturing process of Print Circuit Board (PCB). This study also examines the influences of various factors on the properties of the generated powder. These factors include the reaction temperature, the inflow speed of the raw material solution, the inflow speed of the air, the size of the nozzle tip, and the concentration of the raw material solution. It is discovered that, as the reaction temperature increases from 80$0^{\circ}C$ to 100$0^{\circ}C$ , the particle size of the generated powder increases accordingly, and that the structure of the powder becomes much more compact. When the reaction temperature is 100$0^{\circ}C$, the particle size of the generated powder increases as the concentration of copper in the raw material solution increases to 40g/l, decreases as the concentration increases up to 120g/l, and increases again as the concentration reaches 200g/1. In the case of a lower concentration of the raw material solution, the generated powder appears largely in the form of CuO. As the concentration increases, however, the powder appears largely in the form of CuCl. When the concentration of copper in the raw material solution is 120g/1, the particle size of the generated powder increases as the inflow speed of the raw material solution increases. When the concentration of copper in the raw material solution is 120g/1, there is no evident change in the particle size of the generated powder as the size of the nozzle tip and the air pressure increases. When the concentration is 40g/1, however, the particle size keeps increasing until the air pressure increases to 0.5kg/$\textrm{cm}^2$, but decreases remarkably as the air pressure exceeds 0.5kg/$\textrm{cm}^2$.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2006.05a
• /
• pp.61-65
• /
• 2006

• Analytical Science and Technology
• /
• v.12 no.6
• /
• pp.540-549
• /
• 1999

The combustion temperature was controlled between $880^{\circ}C$ to $1070^{\circ}C$ to find the relation the combustion temperature and emission amount of PCDDs/PCDFs in the Municipal solid waste incinerator. The emission amount of PCDDs/PCDFs decreased when the temperature increased in the rear of the boiler. The PCDDs/PCDFs concentration were detected $7.82ng-TEQ/Nm^3$ at $880^{\circ}C$, $6.97ng-TEQ/Nm^3$ at $970^{\circ}C$ and $6.13ng-TEQ/Nm^3$ at $1070^{\circ}C$. Also, The chlorophenols, chlorobenzenes, and PCB concentration decreased by increasing the temperature from $880^{\circ}C$ to at $1070^{\circ}C$, and the isomer of the prescsors had a tendency to emit the higbly cbiorinated compounds.

• Journal of the Korean Chemical Society
• /
• v.46 no.2
• /
• pp.117-124
• /
• 2002

Counterflow oxidation was developed and evaluated for treatment of organics that adsorbed in/on granular activated carbon(GAC). This reaction is a method that destructs and removes organics adsorbed, at the same time, regenerates waste carbon, uti lizing a self-sustained flame which propagates itself ina direction counter to the oxygen flow. The results showed that the mass loss of carbon and flam temperature were strongly dependent on the flow rate of oxyen, adsorptive capability of regenerated carbon completely was recovered, as well as destrution and removal efficiency of thermally stable PCBs was achieved with the value of better than 99.99%.

• Analytical Science and Technology
• /
• v.18 no.3
• /
• pp.206-215
• /
• 2005

Polychlorinated biphenyls (PCBs) were commercially produced as complex mixtures beginning in 1929. The PCBs manufactured commercially are known by a variety of trade names including; Aroclor (USA), Phenoclor (France), Kaneclor (Japan), Sovol (USSR) and so on. PCBs are a class of 209 congeners that were widely used in a wide variety of applications, including dielectric fluid in transformers and large capacitors; heat transfer fluids; hydraulic fluids; lubricating and cutting oils; and as additives in pesticides, paints, adhesives, sealants, and plastics. The quantification methods of peak matching and coefficient comparison were compared using the Aroclor 1242, 1248, 1254, 1260 standards. Also, six transformer oils were analyzed as a main source of polychlorinated biphenyls (PCBs) emission into the environment. The transformer oils contained the pure and mixed of Aroclor 1242, Aroclor 1254, and Aroclor 1260. The analytical results using two quantification methods showed the little difference between the measured results.

• Resources Recycling
• /
• v.10 no.5
• /
• pp.29-35
• /
• 2001

This study was carried out to recover gold, silver and valuable metals from the printed circuit boards (PCBs) of waste computers. PCBs samples were crushed under 1 mm by a shredder and separated into 30% conducting and loft nonconducting materials by an electrostatic separator. The conducting materials contained valuable metals which were then used as feed materials for magnetic separation. 42% of magnetic materials from the conducting materials was removed by magnetic separation as nonvaluable materials and the others, 58% of non magnetic materials, was used as leaching samples containing 0.227 mg/g Au and 0.697 mg/g Ag. Using the materials of leaching from magnetic separation, more than 95% of copper, iron, zinc, nickel and aluminium was dissolved in 2.0M sulfuric acid solution, added with 0.2M hydrogen peroxide at $85^{\circ}C$. Au and Ag were not extracted in this solution. On the other hand, more than 95% of gold and 100% of silver were leached by the selective leaching with a mixed solvent (0.2M($NH_4$)$_2$$S_2$$O_3$,0.02M $CuSO_4$,0.4M $NH_4$OH). Finally, the residues were reacted with a NaCl solution to leach Pb whereas sulfuric acid was used to leach Sn. Recoveries reached 95% and 98% in solution, respectively.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.4
• /
• pp.163-169
• /
• 2019

Sn-Pb solder alloys in electronics rapidly has been replaced to Pb free solder alloys because of various environmental regulations such as restriction of hazardous substances directive (RoHS), European Union waste electrical, waste electrical and electronic equipment (WEEE), registration evaluation authorization and of chemicals (REACH) etc. Because Sn58%Bi (in wt.%) solder alloy has low melting point and higher mechanical properties than that of Sn-Pb solder, it has been studied to manufacture electronic components. However, the reliability of Sn58%Bi solder could be lowered because of the brittleness of Bi element included in the solder alloy. Therefore, we observed the microstructures of Sn58%Bi composite solders with various contents of Sn-decorated multiwalled carbon nanotube (Sn-MWCNT) particles and evaluated bonding strength of the FR-4 components assembled with Sn58%Bi composite solder. Also, microstructures and bonding strengths of the Sn58%Bi composite solder joints were evaluated with the number of reflows from 1 to 7 times, respectively. Bonding strengths and fracture energies of the Sn58%Bi composite solder joints were measured by die shear test. Microstructures and fracture modes were observed with scanning electron microscope (SEM). Microstructures in the Sn58%Bi composite solder joints were finer than that of only Sn58%Bi solder joint. Bonding strength and fracture energy of Sn58%Bi composite solder including 0.1 wt.% of Sn-decorated MWCNT particles increased up to 20.4% and 15.4% at 5 times in reflow, respectively.