• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.63-66
• /
• 2006

The effect of warm rolling under various conditions on the microstructure and mechanical property was investigated using an AZ31 Mg alloy sheet. Several processing parameters such as initial thickness, thickness reduction by a single pass rolling, rolling temperature, roll speed, and roll temperature were varied to elicit an optimum condition for the warm rolling process of AZ31 Mg alloy. Microstructure and mechanical properties were measured for specimens subjected to rolling experiments of various conditions. Warm rolling of 30% thickness reduction per pass was possible without any side-crack at temperatures as low as $200^{\circ}C$ under the roll speed of 30 m/min. The initial microstructure before rolling was the mixed one consisting of partially recrystallized and cast structures. Grain refinement was found to occur actively during the warm rolling, producing a very fine grain size of 7 mm after 50% reduction in single pass rolling at $200^{\circ}C$. Yield strength of 204MPa, tensile strength of 330MPa and uniform elongation of 32% have been obtained in warm rolled sheets.

• Transactions of Materials Processing
• /
• v.16 no.8
• /
• pp.614-620
• /
• 2007

Deformation characteristics and damage evolution during warm backward extrusion of bulk AZ31 Mg alloy were investigated using finite element analyses. AZ31 Mg alloy was assumed as a hardening viscoplastic material. The tensile tests of AZ31 Mg alloy in previous experimental works showed the ductile fracture even at the warm temperature of $175^{\circ}C$. In this study, damage evolution model proposed by Lee and Dawson, which was developed based on the growth of micro voids in hardening viscoplastic materials, was combined into DEFORM 2D. Effects of forming temperature, punch speed, extrusion ratio and size of work piece on formability in warm backward extrusion as well as on mechanical properties of extruded products were examined. In general, finite element predictions matched the experimental observations and supported the analyses based on experiments. Distributions of accumulated damage predicted by the finite element simulations were effective to identify the locations of possible fracture. Finally, it was concluded that the process model, DEFORM2D combined with Lee & Dawson#s damage evolution model, was effective for the analysis of warm backward extrusion of AZ31 Mg alloys.

• Journal of Acupuncture Research
• /
• v.36 no.3
• /
• pp.131-139
• /
• 2019

Background: This study aimed to investigate the correlation between heat transmission and intervention factors for warm acupuncture (such as features of acupuncture material and moxa, the treatment method, and clinical symptoms). Methods: Korean, English, Chinese and Japanese databases were analysed. Experimental studies that explored the association between thermal stimulation delivery and warm acupuncture intervention factors were included. The peak temperature, time to reach the peak temperature, and time of the effective stimulus, were set as the major parameters and analysed. Results: A total of 12 studies were included. Two studies were associated with the acupuncture needle material, 4 studies associated with the moxa mass, 1 study associated with the moxa density, 2 studies associated with the location of ignition, and 1 study associated with treatment environment were reviewed. The reporting quality of the 12 studies was low. Conclusion: This study provided limited information because of the heterogeneity of materials and parameters depending on each experiment. Further studies should clarify the correlation between heat transmission and intervention factors for warm acupuncture.

• Korean Journal of Plant Resources
• /
• v.22 no.6
• /
• pp.535-539
• /
• 2009

The time of seed collection is regarded as one of major concerns to obtain sound seeds. The physical and germinal aspects of Cryptomeria japonica D. Don (Taxodiaceae) seeds were analyzed to determine the optimum harvesting time in Korea. Cones were picked every 10 days from the $30^{th}$ of July to the $30^{th}$ of October in both 2005 and 2006. Seeds were collected from picked cones. Seed size and weight were not significant in two consecutive years. The 1,000-seed weight was 3.3 g for cones picked at the $18^{th}$ of August and 5.3 g for cones picked at the $30^{th}$ of September. The size of seeds was increased as the time of collection from the $18^{th}$ of August to the $30^{th}$ of September: from 19.3 mm to 21.3 mm in length and from 15.8 mm to 18.5 mm in width. Average germination rates in 2005 was 18.3% and 19.6% in 2006. The highest germination rate was 34.3% from seeds collected at the $30^{th}$ of September in 2005. In 2006, the highest germination rate was 31.7% for seeds collected at the same date as the 2005 seeds. After the end of September, germination rate was decreased in both years. The results implied that the best cone picking time for Korean C. japonica seeds is around the end of September.

• Journal of Environmental Science International
• /
• v.16 no.11
• /
• pp.1313-1318
• /
• 2007

Illicium anisatum was bred under four different light intensity. Those condition were full sunlight(PPFD $1600{\mu} mol\;m^{-2}s^{-1}$), 30% treatment(PPFD $400{\mu} mol\;m^{-2}s^{-1}$), 50% treatment(PPFD $250{\mu} mol\;m^{-2}s^{-1}$) and 70% treatment(PPFD $100{\mu} mol\;m^{-2}s^{-1}$), respectively. Chlorophyll a and b were increased according to decrease of light intensity. Thirty percent and 50% treatment had not significant different in chlorophyll a and b. Thirty percent treatment was shown the best photosynthetic activity through invested photosynthetic rate, intercellular $CO_2$ concentration and water use efficiency. Photosynthetic activity trend of 50% treatment was similar to 30% treatment. Seventy percent treatment was shown the best photosynthetic activity at low light intensity but that was decreased to lower value than 30% and 50% treatment under high intensity. Control, bred full sunlight, was shown the worst photosynthetic activity at measured all light intensity. That result could imply that was caused by photo-inhibition because of long term exposed of shade tolerant plant at high light intensity. Leaf characteristics had not significant different in leaf length, width and area but leaf dry weight had similar trend to photosynthetic activity.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.22 no.2
• /
• pp.205-211
• /
• 2016

Based on the Expendable Bathythermograph (XBT) observation and serial oceanographic observation of National Institute of Fisheries Science (NIFS) during July 2013 to July 2015, we examined the temperature variation in the Ulleung Warm Eddy (UWE) in the East Sea. The UWE was always shown during the observation periods even though it was not the whole shape. The coefficient of variation (CV) was largest in the depth of 250 m at the side of the east coast of Korean Peninsula with $3{\sim}4^{\circ}C$ in temperature. CV of the horizontal distribution at 250 m depth was also largest in the region biased along the east coast of Korea. The warm eddy moved not only to the east-west direction but also to the north-south direction in the viewpoint of horizontal distributions of temperature. This region between the Korean Peninsula and Ulleung island also is the passage of the East Korean Warm Current. This means that interaction between the East Korean Warm Current and periphery of warm eddy makes large in the variation of movement along the east coast of Korean Peninsula. The largest variation of temperature at 250 m depth seemed to be significantly correlated with the East Sea Intermediate Water (ESIW) underlying Ulleung Warm Eddy. It is suggested that the interaction between the ESIW and UWE is active in the mid-depth along the periphery of UWE.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.4
• /
• pp.333-339
• /
• 2008

Densification behavior of copper powder was investigated to study the effect of an aluminum mold under warm pressing. The low flow stress of an aluminum mold is appropriate to apply hydrostatic stress to powder compacts during compaction under high temperature. The suggested powder metallurgy process is very useful under high temperature since copper powder compacts have higher relative density over axial stress of 100 MPa and show more homogeneity as compared with conventional warm pressing. Elastoplastic constitutive equation proposed by Shima and Oyane was implemented into a finite element program (ABAQUS) for densification behavior under warn pressing by using a metal mold. Finite element results agreed well with experimental data for densification and deformation of copper powder compacts in the mold.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.225-228
• /
• 2003

This paper is concerned with pressure welding, which has been known as a main bonding mechanism for the cold and warm clad forming. Bonding characteristics of pressure welding between the copper and aluminum plates are experimentally investigated. Experiments are performed at the cold and warm temperature range with the variation of important factors such as magnitude of pressure, surface roughness of Cu and Al plates, and pressure holding time. It could be concluded that the bonding criterion might be given as a function of bonding pressure and surface roughness for the cold and warm temperature ranges.

• Transactions of Materials Processing
• /
• v.11 no.3
• /
• pp.255-261
• /
• 2002

The grain size of 7010 Al alloy was refined to submicrometer level by using equal channel angular pressing (ECAP) and additional warm rolling. The mechanisms of grain refinement in ECAP process were fragmentation of coarse grain to ultra fine subgrains after a few passes and continuous recrystallization of the subgrains with the increase o( passes. Because of ultrafine grain size, essentially low temperature and high strain rate superplasticity was observed after ECAP process and warm rolling to form a sheet metal. The maximum elongation of 700% was obtained for an ECA pressed specimen after IS passes without warm rolling at $450^{\circ}C$ with strain rate of 5x$10^{-3}$/sec.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.197-198
• /
• 2006

The high pressure compaction without internal lubricant and the high green density even with the pore free density were achieved by the newly developed die wall lubricant for warm compaction. This developed die wall lubricated warm compaction followed by high temperature sintering resulted in not only the superior mechanical property but also the low dimensional change. In this paper, the effects of increasing the green density on the sintered density, the dimensional change and the mechanical property are mainly discussed