• Explosives and Blasting
• /
• v.16 no.3
• /
• pp.25-34
• /
• 1998

This area is covered in Andesite of high compression strength and located in PUSAN SEO-KU. There are many old houses around shaft site. So, we must have a cautious blasting operation. A total of 40 blasts were test at DAE-SHIN Shaft site to study the magnitude and frequency characterization of blast-induced vibration. The effect of viblating frequency on structual damage and site-specific scaling to define th empirical equations were also discussed. The result can be summarized as follows: 1. Some empirical equations were obtained. $V=K\{{\frac{D}{W}}1/3\}^{-n}$ where the values for n and K are estimated to be -1.407 to -2.202 and 643.3489 to 7283.2104 respectively. 2. Dominant frequencies at short distance are in the range of about 75.0 to 91.8 Hz, with some exceptions of about 50Hz, Frequencies observed at long distance are in the range of 10 to 2Hz. It is apparent the shift of dominant frequency down to lower levels at long distance.

• Journal of Astronomy and Space Sciences
• /
• v.23 no.2
• /
• pp.97-104
• /
• 2006

From the BV images of the metal-poor globular cluster NGC 1904 obtained with the 2K CCD camera equipped on the BOAO 1.8m telescope, we construct (B - V, V) color-magnitude diagram of the cluster. The apparent V magnitudes of the RGB bump and tip have been measured from the luminosity function of the iteratively selected RGB stars in NGC 1904. Theoretical absolute $M_v$ magnitudes of the RGB bump and tip are estimated using the Yonsei-Yale isochrones. The distance modulus of NGC 1904 has been derived by comparing the observed apparent V magnitude with the estimated absolute $M_v$ magnitude of the RGB bump and tip.

• 한국정보통신설비학회:학술대회논문집
• /
• 2004.08a
• /
• pp.382-385
• /
• 2004

In this paper, a new clustering algorithm using the Guaranteed Distance is proposed. In the new algorithm, the appropriate distribution of clusterheads is accomplished by guarantee the stochastic average distance between clusterhead (CH)s. Using this algorithm, the communication cost from clusterheads to their member nodes and the load variance in each clusterheads are reduced. Therefore, the network lifetime can be extended and the fair energy consumption for all nodes can be achieved.

• Proceedings of the KIEE Conference
• /
• 1999.07c
• /
• pp.1401-1403
• /
• 1999

This paper presents a distance relaying algorithm for transmission line compensated with Static Synchronous Series Compensator (SSSC). The compensation voltage driven by SSSC is calculated from the line current measured at a relaying point Then the compensation voltage is subtracted from the voltage measured by the relay. We can apply conventional distance relaying algorithm with this subtracted voltage to locate a fault. The results of case studies using EMTP (Electro-Magnetic Transient Program) show the proposed algorithm has higher precision.

• Journal of the Optical Society of Korea
• /
• v.9 no.1
• /
• pp.6-12
• /
• 2005

The perturbation approach is applied to solve the nonlinear Schrodinger equation, and its valid range has been determined by comparing with the results of the split-step Fourier method over a wide range of parameter values. With γ= 2㎞/sup -1/mW/sup -1/, the critical distance for the first order perturbation approach is estimated to be(equation omitted). The critical distance, Z/sub c/, is defined as the distance at which the normalized square deviation compared to the split-step Fourier method reaches 10/sup -3/. Including the second order perturbation will increase Z/sub c/ more than a factor of two, but the increased computation load makes the perturbation approach less attractive. In addition, it is shown mathematically that the perturbation approach is equivalent to the Volterra series approach, which can be used to design a nonlinear equalizer (or compensator). Finally, the perturbation approach is applied to obtain the sinusoidal response of the fiber, and its range of validity has been studied.

• Journal of ILASS-Korea
• /
• v.17 no.1
• /
• pp.27-34
• /
• 2012

In this paper an experimental study is presented to investigate the effect of a step edge and a stationary droplet on the dynamic behavior of impacting droplet on a wall. The main parameters are the distance from the edge and the center-to-center distance between two droplets. Photographic images are presented to show coalescence dynamics, shape evolution and contact line movement. The emphasis is on presenting the spreading length of droplet for the step edge and two coalescing droplets along their original centers. It is clarified that the droplet exhibits much different dynamic behavior depending on the location of the step edge. The momentum of impacting droplet was better transferred to the stationary droplet as the center- to-center distance between two droplets was reduced, which results in more spreading of coalescing droplet.

• Proceedings of the KIEE Conference
• /
• 2003.11a
• /
• pp.82-84
• /
• 2003

This paper presented a method to develop a relay model by the user-written model function of PSS/E. As for the voltage instability, although generator current limiters, transformer's tap-changers and dynamic loads have been considered as the dominant components, the protection system is also very important because it may influence the system's dynamic behaviour. Hence a distance relay model implemented with the suggested method was added, and then the operating characteristics of the distance relay under the voltage instability condition were investigated.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.31 no.1
• /
• pp.45-53
• /
• 1995

Working depth of the model net was determined by using of the same experimental tank and the same model net that used in the forwarded report in a series studies. The depth of the net which indicates the depth of the head rope from the water surface, was determined by the photographs taken in front of the net mouth with the combination of towing velocity, warp length and distance between paired boats. The results obtained can be summarized as follows: 1. Working depth of model nets A and B was varied in the range of 0.09~1.66$m$,and 0.04~1.34$m$(which can be converted into 2.7~40.2$m$and 1.2~49.8$m$in the full-scale net) respectively, and the depth of model net A was slightly deeper than the depth of the model net B. 2. Working depth ($D$,which is appendixed m for the model net, f for the full-scale net, A and B for the types of the model nets) can be expressed as the function of towing velocity$V_t$, as in the model net($V_t$=$m$/$sec$) $D_{mA}$=(-1.99+0.65$L_w$) $e^{-1.72V_t}$ $D_{mA]$=(-1.91+1.04 $L_w$) $e^{2.88V_t}$ in the full-scale net($V_t$=$k$'$t$ $D_{fA}$=(-29.32+0.65$L_w$)$e^{0.40 V_t}$ $D_{fB}$=(-57.60+1.04$L_w$)$e^{-0.67 V_t}$ 3. Working depth 9$D$ appendixes are as same as the former) can be expressed as the function of warp length$L_w$) in the model net, and can be converted into full-scale net as in the model net ($V_t$=$m$/$sec$) $D_{mA}$=-0.99 $e^{-1.42V_t}$+0.67$e^{-1359V_t}$$L_w$ $D_{mB}$=-.258$e^{-3.77V_t}$+1.16$e^{-3.15V_t$ $L^w$, in the full-scale net($V_t$=k't) $D_{fA}$=-29.28$e^{-0.32V_t}$+0.67$e^{-0.37V_t$$L_w$ $D_{fB}$=-69.10$e^{-0.81V_t}$+1.16$e^{-0.72V_t}$$L_w$. 4. Working depth was gradually shallowed according to the increase of the distance between paired boats.

• Korean Journal of Remote Sensing
• /
• v.27 no.4
• /
• pp.411-420
• /
• 2011

In this study, a digital elevation model (DEM) in tidal flat of Suncheon Bay, one of the most ecological preserved area in the world, was generated from digital aerial stereo-images. The focal lengths for the aerial stereo-images were adjusted using ground control points (GCPs) in order to improve the accuracy of camera parameters. We proposed matching sizes suitable for generating DEM in tidal flat and a method for eliminating excessive position errors using intersection-distance($P_R$) threshold value. The accuracies of the DEM generated from the proposed method as well as the commercial S/W were compared with the elevation profiles measured by Total Station in the filed. As the results, the DEM generated by the proposed method showed better result (maximum deviation is a -21 centimeters) with detailed topography than DEM by the commercial S/W in the region. These results suggest that the DEM of tidal flat, which hardly obtained with the traditional methods, can be generated from digital aerial images by applying the proposed method in this study. We believe that the generated DEM in tidal flat can be an essential data for monitoring the sediment erosion and deposit of the tidal flat.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.2
• /
• pp.277-290
• /
• 1999

A simulation using the finite-difference time-domain method to analyze the electromagnetic interactions between a cellular phone and the human body was conducted, and a synthesis of a bone-equivalent material to make a human head phantom was performed. A test model of the cellular phone was fabricated to measure its reflection coefficient and radiation pattern in the free space. Various effects of the human body on the characteristics of the phone, such as input impedance, reflection coefficient, radiation pattern, and radiation efficiency are analyzed as the distance between the head and the phone antenna varies. When the phone was operated close to the head, the resonant frequency of the antenna decreased by up to 12%. With the output power of 0.6W, as long as the distance was larger than 30mm, the 1-g averaged peak SAR was below the ANSI/IEEE safety guideline, 1.6 W/kg. To synthesize the bone-equivalent material, an epoxy with hardener and a graphite powder were used as basis ingredients, and a small amount of a conducting epoxy was added to control the conductivity of the material. A material having a relative permittivity of 18.04 and a conductivity of 0.347, which are close to those of the bone at 850 MHz, was synthesized.