• Journal of Microbiology and Biotechnology
• /
• v.10 no.5
• /
• pp.628-631
• /
• 2000

The timing of poly(3-Hydroxybutyrate) (PHB) biosynthesis was controlled by varying the agitation speed of a stirred tank fermentor during the pH-stat fed-batch culture of recombinant Escherichia coli strain GCSC 6576 harboring pSYL107. Using a concentrated whey solution containing ca. 200 g/l lactose as the nutrient feed, the PHB content was only 57% after 35h due to volumetric limitation of the fermentor. However, by limiting the oxygen by maintaining the agitation speed at 300 rpm, the final PHB content increased to 70% after 70h with a cell concentration of 15 g/l. When the agitation speed was increased up to 500 rpm, a cell concentration of 31 g/l with 80% PHB was obtained after 52h. A further increase in the maximum agitation speed increased the cell concentration, PHB concentration, and PHB productivity, however, the PHB content decreased to 56-58%.

• Steel and Composite Structures
• /
• v.17 no.2
• /
• pp.159-172
• /
• 2014

A finite element model with the consideration of damage initiation and evolution has been developed for the analysis of the dynamic response of a composite sandwich panel subject to low velocity impact. Typical damage modes including fiber breakage, matrix crushing and cracking, delamination and core crushing are considered in this model. Strain-based Hashin failure criteria with stiffness degradation mechanism are used in predicting the initiation and evolution of intra-laminar damage modes by self-developed VUMAT subroutine. Zero-thickness cohesive elements are adopted along the interface regions between the facesheets and the foam core to simulate the initiation and propagation of delamination. A crushable foam core model with volumetric hardening rule is used to simulate the mechanical behavior of foam core material at the plastic state. The time history curves of contact force and the core collapse area are obtained. They all show a good correlation with the experimental data.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.179-180
• /
• 2006

Densification behavior of various metal and ceramic powder was investigated under cold compaction. The Cap model was proposed based on the parameters obtained from axial and radial deformation of sintered metal powder compacts under uniaxial compression and volumetric strain evolution. For ceramic powder, the parameters were obtained from deformation of green powder compacts under triaxial compression. The Cap model was implemented into a finite element program (ABAQUS) to compare with experimental data for densification behavior of various metal and ceramic powder under cold compaction.

• Journal of the Korea Concrete Institute
• /
• v.21 no.2
• /
• pp.159-168
• /
• 2009

In this study, strength, stiffness and confinement effect with stress-strain and stress-volumetric strain curves for improved uniaxial compressive behavior of RC circular columns laterally confined with prestressing aramid fiber strap were experimentally investigated. The test variables were the specimens with or without axial reinforcing bar and the number and spacing of strap, prestressing level, the types of reinforcing fiber (CFS, GFS). As a result, the failure type of the columns was very stable and strength increase rate was about 73% comparison with the general RC columns. Moreover, the strain increase rate is very small and the axial displacement confinement effect was very effective compared with existry methods (CFS, GFS), the initial and final lateral confinement effect was excellent.

• Journal of the Korea Concrete Institute
• /
• v.26 no.2
• /
• pp.159-169
• /
• 2014

This study generalizes the lateral load-displacement relationship of reinforced concrete shear walls from the section analysis for moment-curvature response to straightforwardly evaluate the flexural capacity and ductility of such members. Moment and curvature at different selected points including the first flexural crack, yielding of tensile reinforcing bar, maximum strength, 80% of the maximum strength at descending branch, and fracture of tensile reinforcing bar are calculated based on the strain compatibility and equilibrium of internal forces. The strain at extreme compressive fiber to determine the curvature at the descending branch is formulated as a function of reduction factor of maximum stress of concrete and volumetric index of lateral reinforcement using the stress-strain model of confined concrete proposed by Razvi and Saatcioglu. The moment prediction models are simply formulated as a function of tensile reinforcement index, vertical reinforcement index, and axial load index from an extensive parametric study. Lateral displacement is calculated by using the moment area method of idealized curvature distribution along the wall height. The generalized lateral load-displacement relationship is in good agreement with test result, even at the descending branch after ultimate strength of shear walls.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.13 no.1
• /
• pp.161-171
• /
• 1993

The aim of this study is to provide the stress-strain behavior of hardening geological materials such as rock or concrete on three dimensional spaces by using Desai model based on plastic theory. To validate proposed model, truly triaxial tests with high pressure under variety of stress paths in which three principal stresses were controlled independently using concrete materials were performed. The main results are summerized as follows: 1. Various stress paths for hardening materials used are satisfactorily explained by performing the truly triaxial test with high pressure. This is very important to investigate constitutive equations for materials like rock or concrete. 2. Since the proposed yield function is continuous, it avoids the singularity point at the intersection of two function in the previous models, thus, reducing the difficulties for computer implementation. 3. Analytic predictions for yielding behavior on $J_1-{\sqrt{J_{2D}}}$ octahedral and triaxial plane, as well as volumetric strain and stress-strain behavior agree well with experimental results.

• The Journal of Engineering Geology
• /
• v.8 no.3
• /
• pp.275-284
• /
• 1998

Deformation behavior and microcrack development due to uniaxial compressive cyclic loading in the Pocheon granite were investigated using the ultrasonic velocity measurements and the differential strain analysis(DSA). Most microcracks were developed along the direction parallel to the loading axis. Microcracks developed at the early stage of cyclic loading were formed by propagation of pre-existing cracks. Ultrasonic velocity measurement, DSA and measurement of permanent deformation are good tools to represent microcrack development in rock. Since results from each method are slightly different, microcrack development should be interpreted from all three methods. The magnitude of microcracks developed at the early stage of cyclic loading under 80% loading level is twice compared with those under 70% loading level. The highest volumetric crack strain is about 3000, indicating that the Pocheon granite will fail with 0.3% occupation of microcrack in volume.

• Journal of the Korea Concrete Institute
• /
• v.16 no.3 s.81
• /
• pp.345-356
• /
• 2004

A plasticity model was developed to predict the behavioral characteristics of concrete in multiaxial compression. To extend the applicability of the proposed model to concrete in various stress states, a new approach for failure criteria was attempted. A stress was decomposed into one volumetric and two deviatoric components orthogonal to each other. Three failure criteria wire provided independently for each stress component. To satisfy the three failure criteria, the plasticity model using multiple failure criteria was Implemented. Each failure surface was defined by equivalent volumetric or deviatoric plastic strain. To present dilatancy due to compressive damage a non-associative flow nile was proposed. The proposed model was implemented to finite element analysis, and it was verified by comparisons with various existing test results. The comparisons show that the proposed model predicted well most of the experiments by using three independent failure criteria.

• Journal of Biosystems Engineering
• /
• v.26 no.6
• /
• pp.545-552
• /
• 2001

Nondestructive methods such as ultrasonic and magnetic resonance imaging systems have many advantages but still much expensive. And they do not give exact color information and may miss some details. If it is allowed to destruct a biological object to obtain interior and exterior informations, 3D image visualization model from a series of sliced sectional images gives more useful information with relatively low cost. In this paper, a PC based automatic 3D visualization system is presented. The system is composed of three modules. The first module is the handling and image acquisition module. The handling module feeds and slices a cylindrical shape paraffin, which holds a biological object inside the paraffin. And the paraffin is kept being solid by cooling while being handled. The image acquisition modulo captures the sectional image of the object merged into the paraffin consecutively. The second one is the system control and interface module, which controls actuators for feeding, slicing, and image capturing. And the last one is the image processing and visualization module, which processes a series of acquired sectional images and generates a 3D volumetric model. To verify the condition for the uniform slicing, normal directional forces of the cutting edge according to the various cutting angles were measured using a strain gauge and the amount of the sliced chips were weighed and analyzed. Once the 3D model was constructed on the computer, user could manipulate it with various transformation methods such as translation, rotation, and scaling including arbitrary sectional view.

• Structural Engineering and Mechanics
• /
• v.66 no.4
• /
• pp.505-513
• /
• 2018

Steam flooding is widely used in heavy oil reservoir with coupling effects among the formation temperature change, fluid flow and solid deformation. The effective stress, porosity and permeability in this process can be affected by the multi-physical coupling of thermal, hydraulic and mechanical processes (THM), resulting in a complex interaction of geomechanical effects and multiphase flow in the porous media. Quantification of the state of deformation and stress in the reservoir is therefore essential for the correct prediction of reservoir efficiency and productivity. This paper presents a coupled fluid flow, thermal and geomechanical model employing a program (MATLAB interface code), which was developed to couple conventional reservoir (ECLIPSE) and geomechanical (ABAQUS) simulators for coupled THM processes in multiphase reservoir modeling. In each simulation cycle, time dependent reservoir pressure and temperature fields obtained from three dimensional compositional reservoir models were transferred into finite element reservoir geomechanical models in ABAQUS as multi-phase flow in deforming reservoirs cannot be performed within ABAQUS and new porosity and permeability are obtained using volumetric strains for the next analysis step. Finally, the proposed approach is illustrated on a complex coupled problem related to steam flooding in an oil reservoir. The reservoir coupled study showed that permeability and porosity increase during the injection scenario and increasing rate around injection wells exceed those of other similar comparable cases. Also, during injection, the uplift occurred very fast just above the injection wells resulting in plastic deformation.