• Journal of the Korean Electrochemical Society
• /
• v.13 no.2
• /
• pp.116-122
• /
• 2010

A $Cu_3Si$ film electrode is obtained by Si deposition on a Cu foil using DC magnetron sputtering, which is followed by annealing at $800^{\circ}C$ for 10 h. The Si component in $Cu_3Si$ is inactive for lithiation at ambient temperature. The linear sweep thermammetry (LSTA) and galvano-static charge/discharge cycling, however, consistently illustrate that $Cu_3Si$ becomes active for the conversion-type lithiation reaction at elevated temperatures (> $85^{\circ}C$). The $Cu_3Si$ electrode that is short-circuited with Li metal for one week is converted to a mixture of $Li_{21}Si_5$ and metallic Cu, implying that the Li-Si alloy phase generated at 0.0 V (vs. Li/$Li^+$) at the quasi-equilibrium condition is the most Li-rich $Li_{21}Si_5$. However, the lithiation is not extended to this phase in the constant-current charging (transient or dynamic condition). Upon de-lithiation, the metallic Cu and Si react to be restored back to $Cu_3Si$. The $Cu_3Si$ electrode shows a better cycle performance than an amorphous Si electrode at $120^{\circ}C$, which can be ascribed to the favorable roles provided by the Cu component in $Cu_3Si$. The inactive element (Cu) plays as a buffer against the volume change of Si component, which can minimize the electrode failure by suppressing the detachment of Si from the Cu substrate.

• Tuberculosis and Respiratory Diseases
• /
• v.45 no.6
• /
• pp.1223-1235
• /
• 1998

Background and Objective : Although prone positioning has been reported to improve gas exchange, prone positioning alone does not seem to be sufficient to increase systemic oxygen transport in an acute lung injury. The objective of this study was to investigate whether the combined therapy of low dose nitric oxide (NO) inhalation and prone positioning has an additive effect on the oxygenation and hemodynamics in patients with severe ARDS. Patients and Methods : Twelve patients with ARDS were included. Prone positioning alone, later combined with nitric oxide inhalation (5~10 ppm) from the supine position (baseline) were performed with serial measurement of gas exchange, respiratory mechanics and hemodynamic at sequential time points. The patient was regarded as a responder to prone positioning if an increase in $PaO_2/FiO_2$ of more than 20 mm Hg at 30 min or 120 min intervals after prone positioning was observed compared to that of the baseline. The same criterion was applied during nitric oxide inhalation. Results : Eight patients (66.5%) responded to prone positioning and ten patients (83.3%) including the eight just mentioned responded to the addition of NO inhalation. The $AaDO_2$ level also decreased promptly with the combination of prone positioning and NO inhalation compared to that of prone positioning alone ($191{\pm}109$ mm Hg vs. $256{\pm}137$ mm Hg, P<0.05). Hemodynamic parameters and lung compliance did not change significantly during prone positioning only. Following the addition of NO inhalation to prone positioning, the mean pulmonary artery pressure and pulmonary artery occlusion pressure decreased and cardiac output, stroke volume and oxygen delivery increased (P < 0.05) compared to those of prone 120 min. Conclusion : These findings indicate that NO inhalation would provide additional improvement in oxygenation and oxygen transport to mechanically ventilated patients with ARDS who are in a prone position.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.34 no.7
• /
• pp.959-967
• /
• 2005

Lead is a ubiquitous environmental and industrial pollutant that causes a major health concerns. It is known to induce a broad range of physiological, biochemical, and behavioral dysfunctions in laboratory and humans, including hematopoietic system, kidneys, liver, and reproductive system. This study was conducted to investigate the effect of Saengshik supplementation on the lead-induced toxicity in rats. Five week old male Sprague­Dawley rats were randomly assigned to five groups for six weeks as followings: control group (CT), lead acetate treated group (PT), and lead acetate groups administered with three different dosages of Saengshik $(SI2.5-12.5\%,\;S25-25\%,\;and\;S50-50\%).$ Lead acetate (12 mg/rat) was intragastrically administered daily for 6 weeks. The results were summarized as follows; Weight gain and food efficiency ratio were significantly lower (p<0.05) in lead administered group compared with those of the control group. Also, significant lead-induced alteration in blood hemoglobin (HGB), hematocrit (HCT), mean corpuscular volume (MCV), mean corpuscular hemoglobin (MCH), and reticulocyte distribution width (RDW) were observed. In the liver of lead-exposed animals, there was an increase in the lipid peroxidation (MDA) and the level of glutathione (GSH), but superoxiede dismutase (SOD) activity did not change. Lead-exposed animals with $25\%\;and\;50\%$ Saengshik supplementation showed marked improvements in the values of MCH, MCV, and RDW. Also, the level of HCT was significantly increased by $50\%$ Saengshik supplementation. The levels of liver MDA in $12.5\%\;and\;50\%$ Saengshik administered groups and GSH level in $50\%$ Saengshik administered group were significantly decreased compared to the lead administered group. Also, hepatic SOD activity tended to increase in the presence of Saengshik supplementation. Furthermore, the accumulation of lead in liver and kidney was reduced by presence of Saneghshik supplementation. Liver lead concentration was significantly reduced by both $25\%\;and\;50\%$ Saengshik supplementations and kidney lead concentration was significantly reduced by the $25\%$ Saengshik supplementation. These results show that Saengshik may have a protective effect against lead intoxication but the mechanism of their effects remains unclear.

• Journal of Bio-Environment Control
• /
• v.24 no.2
• /
• pp.100-105
• /
• 2015

The calculation method of infiltration loss in greenhouse has different ideas in each design standard, so there is a big difference in each method according to the size of greenhouses, it is necessary to establish a more accurate method that can be applied to the domestic. In order to provide basic data for the formulation of the calculation method of greenhouse heating load, we measured the infiltration rates using the tracer gas method in plastic greenhouses equipped with various thermal curtains. And then the calculation methods of infiltration loss in greenhouses were reviewed. Infiltration rates of the multi-span and single-span greenhouses were measured in the range of $0.042{\sim}0.245h^{-1}$ and $0.056{\sim}0.336h^{-1}$ respectively, single-span greenhouses appeared to be slightly larger. Infiltration rate of the greenhouse has been shown to significantly decrease depending on the number of thermal curtain layers without separation of single-span and multi-span. As the temperature differences between indoor and outdoor increase, the infiltration rates tended to increase. In the range of low wind speed during the experiments, changes of infiltration rate according to the outdoor wind speed could not find a consistent trend. Infiltration rates for the greenhouse heating design need to present the values at the appropriate temperature difference between indoor and outdoor. The change in the infiltration rate according to the wind speed does not need to be considered because the maximum heating load is calculated at a low wind speed range. However the correction factors to increase slightly the maximum heating load including the overall heat transfer coefficient should be applied at the strong wind regions. After reviewing the calculation method of infiltration loss, a method of using the infiltration heat transfer coefficient and the greenhouse covering area was found to have a problem, a method of using the infiltration rate and the greenhouse volume was determined to be reasonable.

• Cartoon and Animation Studies
• /
• s.36
• /
• pp.469-491
• /
• 2014

Webtoon has developed the method that makes it possible to express sound visually. Also we can also hear sound in webtoon through the development of web technology. It is natural that we analyze the sound that we can hear, but we can also analyze the sound that we can not hear. This study is based on 'dual code' in cognitive psychology. Cartoonists can make visual expression on the basis of auditive impression and memory, and readers can recall the sound through the process of memory and memory-retrieval. This study analyzes both audible sound and inaudable sound. Concise analysis owes the method to film sound theory. Three main factor, Volume, pitch, and tone are recognized by frequency in acoustics. On the other hand they are expressed by the thickness and site of line and image of sound source. The visual expression of in screen sound and off screen sound is related to the frame of comics. Generally the outside of frame means off sound, but some off sound is in the frame. In addition, horror comics use much sound for the effect of genre like horror film. When analyzing comics sound using this kinds of the method film sound analysis, we can find that webtoon has developed creative expression method comparing with simple ones of early comics. Especially arranging frames and expressing sound following and vertical moving are new ones in webtoon. Also types and arrangement of frame has been varied. BGM is the first in using audible sound and recently BGM composed mixing sound effect is being used. In addition, the program which makes it possible for readers to hear sound according to scroll moving. Especially horror genre raise the genre effects using this technology. Various methods of visualizing sound are being created, and the change shows that webtoon could be the model of convergence in contents.

• Restorative Dentistry and Endodontics
• /
• v.34 no.5
• /
• pp.450-459
• /
• 2009

The aim of this study was to measure the initial dynamic modulus changes of light cured composites using a custom made rheometer. The custom made rheometer consisted of 3 parts: (1) a measurement unit of parallel plates made of glass rods, (2) an oscillating shear strain generator with a DC motor and a crank mechanism, (3) a stress measurement device using an electromagnetic torque sensor. This instrument could measure a maximum torque of 2Ncm, and the switch of the light-curing unit was synchronized with the rheometer. Six commercial composite resins [Z-100 (Z1), Z-250 (Z2), Z-350 (Z3), DenFil (DF), Tetric Ceram (TC), and Clearfil AP-X (CF)] were investigated. A dynamic oscillating shear test was undertaken with the rheometer. A certain volume ($14.2\;mm^3$) of composite was loaded between the parallel plates, which were made of glass rods (3 mm in diameter). An oscillating shear strain with a frequency of 6 Hz and amplitude of 0.00579 rad was applied to the specimen and the resultant stress was measured. Data acquisition started simultaneously with light curing, and the changes in visco-elasticity of composites were recorded for 10 seconds. The measurements were repeated 5 times for each composite at $25{\pm}0.5^{\circ}C$. Complex shear modulus G*, storage shear modulus G', loss shear modulus G" were calculated from the measured strain-stress curves. Time to reach the complex modulus G* of 10 MPa was determined. The G* and time to reach the G* of 10 MPa of composites were analyzed with One-way ANOVA and Tukey's test ($\alpha$ = 0.05). The results were as follows. 1. The custom made rheometer in this study reliably measured the initial visco-elastic modulus changes of composites during 10 seconds of light curing. 2. In all composites, the development of complex shear modulus G* had a latent period for $1{\sim}2$ seconds immediately after the start of light curing, and then increased rapidly during 10 seconds. 3. In all composites, the storage shear modulus G" increased steeper than the loss shear modulus G" during 10 seconds of light curing. 4. The complex shear modulus of Z1 was the highest, followed by CF, Z2, Z3, TC and DF the lowest. 5. Z1 was the fastest and DF was the slowest in the time to reach the complex shear modulus of 10 MPa.

• Korean journal of food and cookery science
• /
• v.28 no.4
• /
• pp.391-397
• /
• 2012

This study was carried out to investigate commercialization of Kimchi made of cabbage (Brassica oleracea var. capitata L.) using pre-fermentation conditions. The pre-fermentation conditions were 0, 18, 24, and 28 h at $20^{\circ}C$, and then the samples were stored at $10^{\circ}C$ to assess changes in quality characteristics. A comparison of the quality characteristics during storage showed that PF24 (pre-fermented cabbage Kimchi during 24 h at $20^{\circ}C$) and PF28 (pre-fermented cabbage Kimchi during 28 h at $20^{\circ}C$) had pH 4.47 and pH 4.23 on the second day of storage, respectively. It was possible to shorten the fermentation time to less than that of PF0 (not pre-fermented cabbage Kimchi at $20^{\circ}C$), by approximately 3 days. Total acidity was 0.26 to 0.29% immediately after making the Kimchi. However, PF0, PF18 (pre-fermented cabbage Kimchi during 18 h at $20^{\circ}C$), PF24 and PF28 became well-fermented when they were stored for 8~14 days, 3~10 days or 2~3 days. The number of lactic acid bacteria increased with the passage of time in all treatment groups regardless of fermentation conditions. However, the longer pre-fermentation time became, the faster the number of lactic acid bacteria increased. Most samples showed similar results late in the storage period; 7.2~7.4 log CFU/mL. PF0 had the greatest volume change 2.1 times increase late in the storage period. The sensory evaluation showed significant differences for flavor, taste, and overall acceptability after a partial storage period. PF28 stored for 2~3 days showed excellent flavor, and PF24 and PF28 stored for 2~3 days showed the highest scores of 6.27 to 6.67. The PF24 and PF28 treated samples were appropriate for commercializing small packed cabbage Kimchi and for alleviating the expansion problem of the packing material. However, because mass commercial production requires a large number of samples to be used at once, the results should be assessed for industrial product development in the future.

• Korean Journal of Food Science and Technology
• /
• v.34 no.3
• /
• pp.449-453
• /
• 2002

This was studied to evaluate the quality characteristics of the bread added chitosan during storage at room temperature(Temp. $27^{\circ}C{\pm}2$, RH $75%{\pm}10$). The volume of the dough was increased depending on the larger molecular weight and the higer concentration of chitosan but was decreased at 0.50% of 120 kDa chitosan. The water activity was low depending on the larger molecular weight and the higher concentration of chitosan at the early storage, but maintained constantly during storage totally. The colors of the bread was hardly affected by 30 kDa of chitosan. Textural characteristics was improved at 30 kDa and 120 kDa of chitosan. Especially, the change of the hardness were maintained lower at 30 kDa, 120 kDa of chitosan during storage than that of standard. These results showed that the quality of the bread by added 30 kDa of chitosan was improved highly.

• Journal of the Korean Institute of Gas
• /
• v.8 no.2 s.23
• /
• pp.15-27
• /
• 2004

The purpose of this paper is to improve the performance of Polymer electrolyte fuel cell(PEMFC) by studying the channel dimension of bipolar plates using commercial CFD program 'Fluent'. Simulations are done ranging from 0.5 to 3.0mm for different size in order to find the channel size which shoves the highst hydrogen consumption. The results showed that the smaller channel width, land width, channel depth, the higher hydrogen consumption in anode. When channel width is increased, the pressure drop in channel is decreased because total channel length Is decreased, and when land width is increased, the net hydrogen consumption is decreased because hydrogen is diffused under the land width. It is also found that the influence of hydrogen consumption is larger at different channel width than it at different land width. The change of hydrogen consumption with different channel depth isn't as large as it with different channel width, but channel depth has to be small as can as it does because it has influence on the volume of bipolar plates. however the hydrogen utilization among the channel sizes more than 1.0mm which can be machined in reality is the most at channel width 1.0, land width 1.0, channel depth 0.5mm and considered as optimum channel size. The fuel cell combined with 2cm${\times}$2cm diagonal or serpentine type flow field and MEA(Membrane Electrode Assembly) is tested using 100W PEMFC test station to confirm that the channel size studied in simulation. The results showed that diagonal and serpentine flow field have similarly high OCV and current density of diagonal (low field is higher($2-40mA/m^2$) than that of serpentine flow field under 0.6 voltage, but the current density of serpentine type has higher performance($5-10mA/m^2$) than that of diagonal flow field under 0.7-0.8 voltage.

• Korean Journal of Dental Materials
• /
• v.45 no.4
• /
• pp.257-274
• /
• 2018

The purpose of this study was to evaluate the effect of acid-treatment conditions on the surface properties of the RBM (Resorbable Blast Media) treated titanium. Disk typed cp-titanium specimens were prepared and RBM treatments was performed with calcium phosphate ceramic powder. Acid solution was mixed using HCl, $H_2SO_4$ and deionized water with 4 different volume fraction. The RBM treated titanium was acid treated with different acid solutions at 3 different temperatures and for 3 different periods. After acid-treatments, samples were cleaned with 1 % Solujet solution for 30 min and deionized water for 30 min using ultrasonic cleanser, then dried in the electrical oven ($37^{\circ}C$). Weight of samples before and after acid-treatment were measured using electric balance. Surface roughness was estimated using a confocal laser scanning microscopy, crystal phase in the surface of sample was analyzed using X-ray diffractometer. Surface morphology and components were evaluated using Scanning Electron Microscope (SEM) with Energy Dispersive X-ray spectroscopy (EDX) and X-ray Photoemission Spectroscopy (XPS). Values of the weight changes and surface roughness were statistically analyzed using Tukey-multiple comparison test (p=0.05). Weight change after acid treatments were significantly increased with increasing the concentration of $H_2SO_4$ and temperature of acid-solution. Acid-treatment conditions (concentration of $H_2SO_4$, temperature and time) did not produce consistent effects on the surface roughness, it showed the scattered results. From XRD analysis, formation of titanium hydrides in the titanium surface were observed in all specimens treated with acid-solutions. From XPS analysis, thin titanium oxide layer in the acid-treated specimens could be evaluated. Acid solution with $90^{\circ}C$ showed the strong effect on the titanium surface, it should be treated with caution to avoid the over-etching process.