• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.501-503
• /
• 2008

This paper presents the design of a 2.4 GHz low phase noise fully integrated LC Voltage-Controlled-Oscillator (VCO) in $0.18{\mu}m$ CMOS technology. The VCO is without any tail bias current sources for a low phase noise and, in which differential varactors are adopted for the symmetry of the circuit. At the same time, the use of differential varactors pairs reduces the tuning range, i.e., the frequency range versus VTUNE, so that the phase noise becomes lower. The simulation results show the achieved phase noise of -138.5 dBc/Hz at 3 MHz offset, while the VCO core draws 3.9mA of current from a 1.8V supply. The tuning range is from 2.28GHz to 2.55 GHz.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.11
• /
• pp.2480-2486
• /
• 2012

The design of low voltage LC-VCO(LC Voltage Controlled Oscillator) has been presented to optimize the phase noise and power consumption for the block of frequency synthesis to satisfy WCDMA system specification in this paper. The parameters for minimum phase noise has been obtained in the region of design, using the lines of the tuning range and the excess gain in the plane of the inductance and the transconductance of MOS transistor to compensate the loss of LC-tank. As a result of simulation, the phase noise characteristics is -113dBc/Hz for offset of 1MHz. The optimum designed LC-VCO has been fabricated using the process of 0.25um CMOS. As a result of measurement for fabricated chip, the phase noise characteristics is -116dBc/Hz for offset of 1MHz. The power consumption is 15mW, and Kvco is 370MHz/V.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.8 no.3 s.22
• /
• pp.64-72
• /
• 2005

In this paper, we propose a design method of the millimeter-wave(W-Band) waveguide cavity harmonic voltage controlled oscillator(VCO) using a Gunn diode for the armor sensor. Using the 3-dimensional simulation tool(Ansoft $HFSS^{TM}$), we were able to find the impedance matching point between waveguide and Gunn diode and estimate the oscillation frequency. A varactor diode is used for the frequency tuning, and we find out the equation for the calculation of the tunable frequency range. The designed VCO shows good performances; 17dBm output power at 94GHz center frequency, 520MHz frequency tuning range similar to the estimated value(480MHz).

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.3
• /
• pp.55-60
• /
• 2014

For an high speed communication, a 40GHz VCO was implemented using a 0.11um standard CMOS technology. The mm-wave VCO was designed by a LC type using a spiral inductor, and a simplified architecture with buffers and a smart biasing technique were used to get a high performance. The frequency range of the proposed VCO is 34~40GHz which is suitable for mm-Wave communication system. It has an output power of -16dBm and 16% tuning range. And the phase noise is -100.33dBc/Hz at 1MHz offset at 38GHz fundamental frequency. The total power consumption of VCO including PADs is 16.8mW with 1.2V supply voltage. The VCO achieves the FOMT of -183.8dBc/Hz which is better than previous VOCs.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.12
• /
• pp.24-30
• /
• 1996

In this paper, we designed a new type of high frequency on-chip voltage controlled oscillator (VCO) using GaAs MESFET, and their performances were comapred with those of the conventional VCO. Each VCO was designed with three-to-five ring oscillator and inverter, buffer and NOR gate were implemented by GaAs source coupled FET logic, which has better speed and noise performance compared to other GaAs MESFET logic. SPICE simulation showed that the gain of conventional and our new VCO was 1.24[GHz/V], 0.54[GHz/V], respectively. The frquency tuning range were 2.31 to 3.55 [GHz] for conventional VCO and 2.47 to 3.01[GHz] for our new design. This shows that the factor of two gain reductin was achieved without too much sacrifice in the oscillation frequency. For our new VCO, the average temperature index was -2[MHz/.deg. C] in the range of -20~85[.deg. C] the power supply noise index was 5[MHz/%] for 5.3[V].+-.10[%] and total power consumption was 60.58[mW].

• Journal of Advanced Navigation Technology
• /
• v.8 no.1
• /
• pp.57-65
• /
• 2004

In this paper, keeping pace with light weight, pocket-size, lower-price, we design VCO(Voltage Controlled Oscillator) X/Ku band for using at public RD(Radar Detector) to apply to controlled voltage on base in transistor which used as a oscillator, without using varactor diode in part of VCO tuner. As a result of simulation, we conclude VCO could be have 110 MHz by controlled voltage 4.25 V to 4.80 V and show its output 9.63 dBm at operating frequency, 11.46 GHz, and its phase noise -107.2 dBc at 1 MHz offset frequency. So it turned out suitable performance for commercial use.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.12
• /
• pp.2205-2209
• /
• 2007

In this paper, a voltage controlled oscillator(VCO) of core components for wireless subscriber network is designed. The type of oscillator is colpits method and the oscillator device uses a LC resonator. The product is made on FR-4 substrate with dielectric constant of 4.6. The designed VCO is operated at 3.2V, 10mA and has output value of 0.67dB. The VCO's phase noise property is -102DBc/Hz at offset frequence of 100kHz. The fabricated VCO is the same as target value and can be used for wireless subscriber network.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.6
• /
• pp.843-849
• /
• 1998

A voltage controlled oscillator using dielectric resonator for 2.4 GHz WLL System is designed and fabricated. To improve the phase noise characteristic resonator is used as an inductor of VCO. At the bias condition of 5 V and 10 mA, the output power and phase noise in the operating frequency range of 2210~2240 MHz are 0 dBm and 100 dBc/Hz 10 kHz offset from the carrier, respectively. The phase noise and harmonic response of fabricated VCO are suitable for WLL system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.12
• /
• pp.1236-1242
• /
• 2014

In this work, a D-band VCO(Voltage Controlled Oscillator) has been developed in a 65-nm CMOS technology. The circuit was designed based on push-push mechanism. The output oscillation frequency of the fabricated VCO varied from 152.7 GHz to 165.8 GHz, and the measured output power was from -17.3 dBm to -8.7 dBm. A phase noise of -90.9 dBc/Hz is achieved at 10 MHz offset. The chip size of the circuit is $470{\mu}m{\times}360{\mu}m$ including the probing pads.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1506-1508
• /
• 2005

VCO(voltage controlled oscillator) using mobile communication device decides direct characteristics as parts that affect important in stable oscillation and distortion characteristics of system. VCO used 900 MHz band was designed by the transformation of Colpitts circuit form use ADS that consider Q-factor to minimize phase noise. VCO manufactured together evaluation board and voltage control oscillator to FR-4 PCB. VCO experimented chracteristics after control through resonance department tuning. In our research, the designed VCO has 15.5 dBm output level at the bias condition of 6V and 10mA and the operating frequency range of 917 MHz$\sim$937 MHz band. Phase noise is -98.28 dBc/Hz at 1 MHz frequency offset from the carrier.