• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.7
• /
• pp.1660-1671
• /
• 2013

In this paper two types of power management circuits for solar energy harvesting self-powered systems are proposed. First, if the output voltage of a solar cell is enough to drive load, a power management unit(PMU) directly supplies load with solar energy. Second, if a solar cell outputs very low voltage less than 0.5V as in miniature solar cells or monolithic integrated solar cells such that it cannot directly power the load, a voltage booster is employed to step up the solar cell's output voltage, and then PMU delivers the boosted voltage to the load. The proposed power management systems are designed and fabricated in a $0.18{\mu}m$ CMOS process, and their performances are compared and analyzed through measurements.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.559-560
• /
• 2008

In this paper, I proposed 10bits 40MS/s Pipelined A/D converter. The op-amps for SHA and MDAC designed folded-cascode amplifier with gain-booster. And the MOS transistors with a low threshold voltage are employed to low on-resistor and parasitic capacitance. The power dissipation is 119㎽ at 1.2V and 40MS/s

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.1
• /
• pp.28-35
• /
• 2007

In this paper, an ultra low voltage SRAM design method based on dual-boosted cell bias technique is described. For each read/write cycle, the wordline and cell power node of the selected SRAM cells are boosted into two different voltage levels. This enhances SNM(Static Noise Margin) to a sufficient amount without an increase of the cell size, even at sub 1-V supply voltage. It also improves the SRAM circuit speed owing to increase of the cell read-out current. The proposed design technique has been demonstrated through 0.8-V, 32K-byte SRAM macro design in a $0.18-{\mu}m$ CMOS technology. Compared to the conventional cell bias technique, the simulation confirms an 135 % enhancement of the cell SNM and a 31 % faster speed at 0.8-V supply voltage. This prototype chip shows an access time of 23 ns and a power dissipation of $125\;{\mu}W/Hz$.

• Journal of IKEEE
• /
• v.21 no.1
• /
• pp.66-69
• /
• 2017

In recent year, energy harvesting technologies from the ambient environments such as light, motion, wireless waves, and temperature again a lot of attraction form research community [1-5] due to its efficient solution in order to substitute for conventional power delivery methods, especially in wearable together with on-body applications. The drawbacks of battery-powered characteristic used in commodity applications lead to self-powered, long-lifetime circuit design. Thermoelectric generator, a solid-state sensor, is useful compared to the harvesting devices in order to enable self-sustained low-power applications. TEG based on the Seebeck effect is utilized to transfer thermal energy which is available with a temperature gradient into useful electrical energy. Depending on the temperature difference between two sides, amount of output power will be proportionally delivered. In this work, we illustrated a low-input voltage energy harvesting circuit applied discontinuous conduction mode (DCM) method for getting an adequate amount of energy from thermoelectric generator (TEG) for a specific wearable application. With a small temperature gradient harvested from human skin, the input voltage from the transducer is as low as 60mV, the proposed circuit, fabricated in a $0.6{\mu}m$ CMOS process, is capable of generating a regulated output voltage of 4.2V with an output power reaching to $40{\mu}W$. The proposed circuit is useful for powering energy to battery-less systems, such as wearable application devices.

• Journal of Convergence for Information Technology
• /
• v.11 no.3
• /
• pp.14-19
• /
• 2021

In this paper, a method of constructing an inverter circuit that can generate negative voltage required to operate an IT device in a stable using an inexpensive buck device is presented. To do this, the problem of constructing the inverter circuit using the existing buck device was examined, the principle that could prevent this problem was analyzed, and a circuit that could solve this problem was presented. In order to prove the effectiveness of the proposed method, the experimental circuit was constructed and the experiment was conducted. Compared to the operation of the inverter circuit by the existing overcurrent prevention circuit, it was confirmed that the stable operation was performed without an overcurrent phenomenon. Accordingly, it is expected that the performance of the circuit can be greatly improved while a number of peripheral devices for configuring the devices for processing various analog signals used in IT devices as a single power supply can be omitted.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.6
• /
• pp.415-423
• /
• 2018

We herein investigate the E1 pulse for evaluating the conducted performance of transmission lines connected to the electromagnetic pulse protection facilities against a conducted high-altitude electromagnetic pulse threat exposed to an external electromagnetic environment. The existing E1 pulse generator uses the Marx generator high-voltage step-up method; however, in this research, we used the Tesla transformer method to easily change the broadband output voltage(30 to 350 kV). We also analyzed the controller, power supply, high-voltage booster, and pulse-shaping device. The E1 pulse performance using the Tesla transformer was predicted through simulations and validated by measurements.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.1
• /
• pp.76-81
• /
• 2012

Ultrasonic metal welding is one of the welding methods which welds metal by applying high frequency vibrational energy into specific area at constant pressure, avaliable in room temperature and low temperature. Ultrasonic metal welder is consisted of power supply, transducer, booster, and horn. Precise designing is required since each parts' shape, length and mass can affect driving frequency and vibration mode. This paper focused to horn design, its length L was set to 62mm by calculating vibration equation. By performing modal analysis with various shape variable b times integer, when length of b is 30mm the output was 39,599Hz at 10th mode. Also by performing harmonic response analysis, the frequency response result was 39,533Hz, which was similar to modal analysis result. In order to observe the designed horn's performance, about 4,000 voltage data was obtained from a light sensor and was analyzed by FFT analysis using Origin Tool. The result RMS amplitude was approximately 8.5${\mu}m$ at 40,000Hz, and maximum amplitude was 12.3${\mu}m$. Therefore, it was verified that the ultrasonic metal welding horn was optimally designed.

• Journal of Power Electronics
• /
• v.16 no.4
• /
• pp.1455-1468
• /
• 2016

This paper presents a grid-connected dual stator-winding induction generator (DWIG) wind power system suitable for wide wind speed ranges. The parallel connection via a unidirectional diode between dc buses of both stator-winding sides is employed in this DWIG system, which can output a high dc voltage over wide wind speed ranges. Grid-connected inverters (GCIs) do not require booster converters; hence, the efficiency of wind energy utilization increases, and the hardware topology and control strategy of GCIs are simplified. In view of the particularities of the parallel topology and the adopted generator control strategy, we propose a novel excitation-capacitor optimization solution to reduce the volume and weight of the static excitation controller. When this excitation-capacitor optimization is carried out, the maximum power tracking problem is also considered. All the problems are resolved with the combined control of the DWIG and GCI. Experimental results on the platform of a 37 kW/600 V prototype show that the proposed DWIG wind power system can output a constant dc voltage over wide rotor speed ranges for grid-connected operations and that the proposed excitation optimization scheme is effective.

• Journal of IKEEE
• /
• v.25 no.1
• /
• pp.206-211
• /
• 2021

This paper proposes a Self-Reset Zero-Current Switching (ZCS) Circuit for thermoelectric energy harvesting. The Self-Reset ZCS circuit minimizes the operating current consumed by the voltage comparator, thereby reduces the power consumption of the energy harvesting circuit and improves the energy conversion efficiency by adding the self-reset function to the comparator. The Self-Reset ZCS circuit shows 3.4% of improvement in energy efficiency compared to the energy harvesting system with the conventional analog comparator ZCS for the output/input voltage ratio of 5.5 as a result of circuit simulation. The proposed circuit is useful for improving the performance of the wearable and bio-health-related harvesting circuits, where low-power and energy-efficient thermoelectric energy harvesting is needed.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.5
• /
• pp.117-122
• /
• 2022

In this study, Electromagnetic Induction Power Generation (EMG) is a structure consisting of a stator and a permanent magnet rotor, and is a method that enables power generation by using the kinetic energy of the human arm. Among them, the axial flux permanent magnet (AFPM) technique is a method that can act sensitively to the kinetic energy of the arm at a slow speed of the human body, and has a simple structure and can be designed and manufactured with an ultra-small size. Under the conditions of size of ø46×11mm, rotation speed of 7Hz (420rpm), output voltage 0.4VAC, output current 4.5mA, and output power 30mW were measured and analyzed the same as the target specification. Therefore, the purpose of this study is to study the power generation of the pendulum applying the AFPM (Axial Flux Permanent Magnet) technique to charge power to smart devices with kinetic energy of the human body.