• 한국가스학회지
• /
• 제19권5호
• /
• pp.41-46
• /
• 2015

알루미늄 6061-T6는 $Mg_2Si$와 ${\beta}-Al_5FeSi$로 구성되며, 피로 손상도가 증가하면 ${\beta}-Al_5FeSi$주변에서 기공이 발생하고 성장하는 것으로 알려져 있다. 본 연구에서는 우선 알루미늄 6061-T6 시편에 대한 SEM 촬영을 통해 이러한 현상을 확인하였다. 이후, 피로 손상도에 따라 이 시편의 전위댐핑 (dislocation damping), 정합변형률 (coherency strain), 및 기공 (void)이 감쇠계수와 비선형인자에 미치는 영향을 실험적으로 관찰하였다. 그 결과 비선형인자는 피로 손상도가 증가에 따라 증가하다가 피로수명 75% 이후에서는 감소하는 것을 확인하였다. 이는 전위댐핑과 정합변형률이 증가할수록 비선형인자는 증가하지만, 기공이 증가하면 초음파의 산란이 커져 비선형인자가 감소하는 것으로 해석할 수 있다. 따라서, 피로에 따라 조직변화가 복잡하게 나타나는 재료의 열화 평가에 있어서는 비선형인자를 주의하여 활용하여야 한다는 결론을 얻었다.

• 한국도로학회논문집
• /
• 제9권4호
• /
• pp.135-147
• /
• 2007

아스팔트 포장에서의 골재분리(segregation)는 혼합물 내의 굵은골재와 잔골재가 고르게 분포하지 않은 결과이며, 균열, 레블링(raveling), 박리(stripping)와 같은 조기 파손을 야기한다. 그러나 소성변형에 대한 골재분리의 효과는 아직까지 제대로 규명되지 못하고 있다. 본 연구에서 수행된 실험 및 분석 결과, 아스팔트 포장의 소성변형은 혼합물의 골재분리보다는 혼합물 내의 골재 구조에 더 큰 영향을 받음을 알 수 있었다. 또한 굵은골재의 체적이 증가함에 따라 혼합물의 소성변형 저항성은 증가하였다. 그러나 이러한 현상은 낮은 공극율을 갖는 혼합물에서는 잘 일치하였지만, 높은 공극율을 갖는 혼합물에서는 골재의 체적 증가 보다는 공극율 자체가 소성변형에 더 큰 영향을 줌을 알 수 있었다. 즉, 공극율 10%를 기준으로, 이를 초과하는 혼합물은 굵은 골재의 체적이 큼에도 불구하고 소성변형 저항성은 크게 감소함을 알 수 있었다.

• Steel and Composite Structures
• /
• 제37권4호
• /
• pp.419-429
• /
• 2020

Composite structures are generally pressurized at both sides when repaired by the scarf repair method. But single-face vacuum bag curing (SVC) may be used in some practical scarf repair of penetration damage due to the low accessibility of composite structures, which can decrease bonding quality and may reduce structural mechanical properties. In this paper, experimental investigations were conducted on tensile and compressive properties of scarf-repaired composite laminates using SVC and double-face vacuum bag curing (DVC) in four hygrothermal environments. Finite element models of composite scarf joints with voids were established to further explore the failure mechanism of scarf-repaired laminates. Results show that the curing condition hardly affects tensile and compressive properties of the repaired laminates though it significantly affects the bonding quality with adhesive inner voids. Failure loads of scarf joints almost keep unchanged with adhesive voids increasing.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권4호
• /
• pp.464-471
• /
• 2002

Porosity formation in partial penetration welds by high power lasers is a serious problem in industry. There are two main causes that induce porosity formation. One form of porosity is due to gases (e.g. hydrogen, oxygen) dissolving into the weld pool because of the high temperature and then the rapid solidification traps gases as a bubble in the weld metal. The second problem is voids formed by the keyhole collapsing due to unstable keyhole fluid dynamics. The voids that form at the bottom of the keyhole are relatively large and irregular in shape compared to the gas bubbles; this void formation is the primary concern in this paper. The reduction of voids formed by keyhole collapse is achieved by improving the stability of keyhole. Two methods to improve keyhole stability are discussed in this paper: pulse modulation and beam incident angle. Pulse modulation of the laser beam was performed between 100 Hz and 500 Hz to find out the optimum frequency for the keyhole dynamics. The incident beam angle changed the impact angle of the laser beam to the work surface in a range of 0 to 25 degrees. Glycerin in a semi-solidified state is used as a medium for performing the welding because its transparency allows of visualization of the keyhole.

• 한국환경복원기술학회지
• /
• 제2권2호
• /
• pp.62-69
• /
• 1999

This study was carried out to find out the capability of applying such materials as porous concrete, could be called environmentally friendly materials, for bringing vegetations. For verying the purpose of the experiments such materials as potland cement and slag cement, coarse aggravates(${\phi}25mm$, ${\phi}18mm$, ${\phi}13mm$) were mixed. In the voids of porous concrete peatmoss and chemical fertilizers were filled, and on the surface of concrete organic soils were adhered for seeding grasses. For testing compressive strength, pH, voids the 12($4mixed{\times}3times$) specimens were manufactured. As results, the compressive strength of porous concretes were from 59 to $267kg/cm^2$ depend on mixed ratios between cements and coarse aggregates. Voids of concrete were from 33% to 40% and the pH were varied pH 8-10.5. So the capability of planting vegetations was to be ascertained. The germination and growth of grasses were not good, but it could be found out that the capability of vegetations on the concretes. For generalizing these results and applying on the construction sites, it is necessary to verificate following studies for various conditions.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.600-605
• /
• 2002

The keyhole formed by high energy density laser-material interaction periodically collapses due to surface tension of the molten metal in partial penetration welds. The collapse sometimes traps a void at the bottom of the keyhole, and it remains as welding defects. This phenomenon is seen as one cause of the instability of the keyhole during laser beam welding. Thus, it seems likely that improving the stability of the keyhole can reduce voids and uniform the penetration depth. The goal of this work is to develop techniques for controlling laser weld keyhole dynamics to reduce weld defects such as voids and inconsistent penetration. Statistical analysis of the penetration depth signals in glycerin determined that keyhole dynamics are chaotic. The chaotic nature of keyhole fluctuations and the ability of laser power modulation to control them have been demonstrated by high-speed video images of laser welds in glycerin. Additionally, an incident leading beam angle is applied to enhance the stability of the keyhole. The quasi-sinusoidal laser beam power of 400Hz frequency and 15$^{\circ}$ incident leading beam angle were determined to be the optimum parameters for the reduction of voids. Finally, chaos analyses of uncontrolled signals and controlled signals were done to show the effectiveness of modulation on the keyhole dynamics. Three-dimensional phase plots for uncontrolled system and controlled system are produced to demonstrate that the chaotic keyhole dynamics is converted to regular periodic behavior by control methods: power modulation and incident leading beam angle.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.577-583
• /
• 2010

In this study, the effect of void formation resulting from gas hydrate dissociation or loss of some particles within soil structure on the strength of soil is examined. Beag-ma river sands with uniform gradation were used to simulate a gas hydrate bearing or washable soil structure. Empty capsules for medicine are used to mimic large voids, which are bigger than soil particle. Beag-ma river sand was miced with 8% cement ratio and 14% water content and compacted into a shear box. The number and direction embedded into a specimen. After 4 hours curing, a series of direct shear test is performed on the capsule embedded cemented sands. Shear strength of cemented sands with capsules depends on the volume and direction. The volume and direction formed by voids are most important factors in strength. A shear strength of a specimen with large voids decreases up to 39% of a specimen without void. The results of this study can be used to predict the strength degradation of gas hydrate bearing sediments after dissociation and loss of fine particles within soil structure.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.310-313
• /
• 2002

Structures obtained with a direct boning of two FZ silicon wafers joined in such a way that a smooth surface of one wafer was attached to the grooved surface of the other were studied. A square net of grooves was made with a conventional photo lithography process. After high temperature annealing the appearance of voids and the rearrangement of structural defects were observed with X-ray diffraction topography techniques. It was shown that the formation of void free grooved boundaries was feasible. In the cases when particulate contamination was prevented, the voids appeared in the grooved structures could be eliminated with annealing. Since it was found that the flattening was accompanied with plastic deformation, this deformation was suggested to be intensively involved in the process of void removal. A model was proposed explaining the interaction between the structural defects resulted in "a dissolution" of cavities. The described processes may occur in grooved as well as in smooth structures, but there are the former that allow to manage air traps and undesirable excess of dislocation density. Grooves can be paths for air leave. According to the established mechanisms, if not outdone, the dislocations form local defect arrangements at the grooves permitting the substantial reduction in defect density over the remainder of the interfacial area.

• 대한기계학회논문집A
• /
• 제23권11호
• /
• pp.1993-2006
• /
• 1999

A Volume Integral Equation Method (VIEM) is applied for the effective analysis of elastic wave scattering problems and plane elastostatic problems in unbounded solids containing general anisotropic inclusions. It should be noted that this newly developed numerical method does not require the Green's function for anisotropic inclusions to solve this class of problems since only Green's function for the unbounded isotropic matrix is involved in their formulation for the analysis. This new method can also be applied to general two-dimensional elastodynamic and elastostatic problems with arbitrary shapes and number of anisotropic inclusions and voids. Through the analysis of plane elastodynamic and elastostatic problems in unbounded isotropic matrix with orthotropic inclusions and voids, it will be established that this new method is very accurate and effective for solving plane elastic problems in unbounded solids containing general anisotropic inclusions and voids.

• Restorative Dentistry and Endodontics
• /
• 제45권1호
• /
• pp.5.1-5.8
• /
• 2020

Objectives: The obturation quality of MTA, Biodentine, Total Fill BC root canal sealer (RCS), and warm gutta-percha (WGP) in teeth with simulated internal root resorption (IRR) was evaluated by using micro-computed tomography. Materials and Methods: Standardized IRR cavities were created using 40 extracted maxillary central incisor teeth and randomly assigned into 4 groups (n = 10). IRR cavities were filled with MTA, Biodentine, Total Fill BC RCS (bulk-fill form) and WGP + Total Fill BC RCS. Percentage of voids between resorptive cavity walls and obturation material (external void), and inside the filling materials (internal voids) were measured. Results: Total Fill BC sealer in the bulk-fill form presented significantly highest values of external and internal void percentages (p < 0.05). Biodentine showed a significantly lowest external void percentage (p < 0.05). WGP + Total Fill BC RCS presented significantly lower values of internal void percentages than all groups (p < 0.05), except Biodentine (p > 0.05). Conclusion: None of the filling materials were created void-free obturation in resorption cavities. Biodentine may favor its application in teeth with IRR over Angelus MTA and bulkfill form of Total Fill BC.