• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.5
• /
• pp.217-221
• /
• 2003

In this work, chemical-solution derived silicate fibers were prepared by mixing tetraethyl orthosilicate, ethanol, distilled water, and hydrochloric acid in order to investigate surface roughness of fiber. Silicate fibers were drawn by using a viscous solution after evaporation at $80^{\circ}C$. The dried gel fibers were finally annealed at $1000^{\circ}C$, $1100^{\circ}C$, $1200^{\circ}C$ and $^1300{\circ}C$ for 60 min in dried air (flow rate = ∼200 ml/min). The crystallinity of the heat-treated silica fiber was analyzed by the X-ray diffraction $\theta$-2$\theta$ scan. A field emission-scanning electron microscope and an atomic force microscope were used to evaluate surface properties. The silicate fiber annealed at $1300^{\circ}C$ showed high value of root mean square roughness and had a relatively inhomogeneous surface structure.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.2
• /
• pp.12-20
• /
• 1998

Exter ballistics of a typical high-speed projectile is studied through a flow-visualization experiment and an unstructured grid Navier-Srokes computation. Experiment produced a schlieren photograph that adequately shows the characteristic features of this complex flow, namely two kinds of oblique cone shocks and turbulent wake developing into the downstream. A hybrid scheme of finite volume-element method is used to simulate the compressible Reynolds-Averaged Navier-Stok- es solution on unstructured grids. Osher's approximate Riemann solver is used to discretize the cinvection term. Higher-order spatial accuracy is obtained by MUSCL extension and van Albada ty- pe flux limiter is used to stabilize the numerical oscillation near the solution discontinuity. Accurate Gakerkin method is used to discretize the viscous term. Explict fourth-order Runge-Kutta method is used for the time-stepping, which simplifies the application of MUSCL extension. A two-layer k-$\varepsilon$ turbulence model is used to simulate the turbulent wakes accurately. Axisymmetric folw and two-dimensional flow with an angle of attack have been computed. Grid-dependency is also checked by carrying out the computation with doubled meshes. 2-D calculation shows that effect of angle of attack on the flow field is negligible. Axi-symmetric results of the computation agrees well with the flow visualization. Primary oblique shock is represented within 2-3 meshes in numerical results, and the varicose mode of the vortex shedding is clearly captured in the turbulent wake region.

• Journal of Biosystems Engineering
• /
• v.15 no.3
• /
• pp.207-218
• /
• 1990

Grains display characteristics of both elastic bodies and viscous fluids when they are subjected to mechanical treatments in harvesting, handling, and processing. This viscoelastic behavior of grains when mechanically stressed must be fully understood to establish maximum machine efficiency and have a minimum degree of grain damage and the highest quality of the final product. The studies were conducted to examine the effect of the moisture content, the loading rate and the initial deformation on the stress relaxation behavior of whole kernel of rough rice, and develop the rheological model to represent its stress relaxation behavior. The following results were obtained from the study. 1. Moisture content had the greatest influence on the initial portion of the relaxation curve. With elapsing time the lower moisture content resulted in the lower residual stress for the Japonica-type rough rice and vice versa for the Indica-type rough rice. But within the ranges of moisture content tested, the degree of stress relaxation per unit strain on the Indica-type rough rice was a little higher than those on the Japonica-type rough rice. 2. The slower loading rate resulted in less initial stress. The decreasing trend of residual stress for all the samples tested with increasing loading rate was shown. 3. The higher initial deformation for all the samples resulted in less initial stress. The increasing of amount of stress relaxation per unit strain with increase of initial stress indicated that viscoelastic properties of rough rice depended not only upon duration of load applied but also initial stress applied. This means that rough rice is nonlinear viscoelastic material. 4. The compression stress relaxation properties of rough rice kernel can be described by a generalized Maxwell model representing by the Maxwell elements.

• Journal of Trauma and Injury
• /
• v.33 no.1
• /
• pp.38-42
• /
• 2020

Purpose: Immediate post-laparotomy hypotension (PLH) is a precipitous drop in blood pressure caused by a sudden release of abdominal tamponade after laparotomy in cases of severe hemoperitoneum. The effect of laparotomy on blood pressure in patients with significant hemoperitoneum is unknown. Methods: In total, 163 patients underwent laparotomy for trauma from January 1, 2013 to December 31, 2015. Exclusion criteria included the following: negative laparotomy, only a hollow viscous injury, and hemoperitoneum <1,000 mL. After applying those criteria, 62 patients were enrolled in this retrospective review. PLH was defined as a decrease in the mean arterial pressure (MAP) ≥10 mmHg within 10 minutes after laparotomy. Results: The mean estimated hemoperitoneum was 3,516 mL. The incidence of PLH was 23% (14 of 62 patients). The MAP did not show significant differences before and after laparotomy (5 minutes post-laparotomy, 67.5±16.5 vs. 68.3±18.8 mmHg; p=0.7; 10 minutes post-laparotomy, 67.5±16.5 vs. 70.4±18.8 mmHg; p=0.193). The overall in-hospital mortality was 24% (15 of 62 patients). Mortality was not significantly higher in the PLH group (two of 14 [14.3%] vs. 13 of 48 [27.1%]; p=0.33). No statistically significant between-group differences were observed in the intensive care unit and hospital stay. Conclusions: PLH may be less frequent and less devastating than it is often considered. Surgical hemostasis during laparotomy is important. Laparotomy with adequate resuscitation may explain the equivalent outcomes in the two groups.

• Journal of the Korean Institute of Gas
• /
• v.24 no.5
• /
• pp.39-46
• /
• 2020

This paper is considered about centerline segregation of API 5L steel used in pipeline. Mn/S, Nb and C were known as segregated elements in the centerline of pipe thickness. The Mn usually was accompanied by S consisting of long viscous shape. Microstructure of the centerline was composed of MnS and Nb/Ti indusions including oxide. The segregation effect in centerline region was analyzed by OM, SEM/EDS and micro Vickers hardness. The Mn, Nb and C are retarded elements in transformation from austenite to ferrite or martensite. These elements could derive a bainitic microstructure as a kind of martensite, which is different from difference and element segregation between in matrix and centerline derived from steel melting and heat treatment.

• Tribology and Lubricants
• /
• v.14 no.4
• /
• pp.15-22
• /
• 1998

Recently, the importance of variable displacement piston pump is increasing in industrial world. Especially, most consumers require various range of pressures and flow rates. Pressure compensator is a system controlling flow rate in piston pump at low cost and, therefore, satisfies the need of consumers. However, the system has serious problems, such as response and leakage. The response and leakage are affected by clearance between actuator piston and cylinder, roughness of surface, and spool overlap. In this paper, these effects are investigated experimentally, and optimal clearance and chamfer is obtained. While diameter of cylinder is fixed and diameter of actuator piston is changed in this experiment, response and leakage are measured. Also parameters such as roughness and processing accuracy are changed for piston of fixed clearance. Experimental setup modelled into several parts of actuator piston, cylinder, spool, and swash plate. Input pressure is changed by function generator and proportional valve. The result of this experiment shows that leakage increases very much in proportion to the increase of clearance, and especially leakage occurs enormously when clearance is more than 0.002. The response is not good because as clearance increases leakage increases and as clearance decreases viscous damping effect increases. Accordingly, it is found out that optimal clearance range exists for tile response, within about 0.0012∼0.0014, at this time. Futhermore, the better roughness and geometrical accuracy of actuator piston are, the smaller are leakage and friction. The paper informs that response and leakage are influenced by and geometrical accuracy of actuator piston, roughness of surface, and the clearance between actuator piston and cylinder, and that optimal design of actuator piston in the pressure compensator is possible.

• Journal of Mechanical Science and Technology
• /
• v.16 no.10
• /
• pp.1303-1313
• /
• 2002

Effects of the reduced frequency of upstream wake on downstream unsteady boundary layer flow were simulated by using a Wavier-Stokes code. The Wavier-Stokes code is based on an unstructured finite volume method and uses a low Reynolds number turbulence model to close the momentum equations. The geometry used in this paper is the MIT flapping foil experimental set-up and the reduced frequency of the upstream wake is varied in the range of 0.91 to 10.86 to study its effect on the unsteady boundary layer flow. Numerical solutions show that they can be divided into two categories. One is so called the low frequency solution, and behaves quite similar to a Stokes layer. Its characteristics is found to be quite similar to those due to either a temporal or spatial wave. The low frequency solutions are observed clearly when the reduced frequency is smaller than 3.26. The other one is the high frequency solution. It is observed for the reduced frequency larger than 7.24. It shows a sudden shift of the phase angle of the unsteady velocity around the edge of the boundary layer. The shift of phase angle is about 180 degree, and leads to separation of the boundary layer flow from corresponding outer flow. The high frequency solution shows the characteristics of a temporal wave whose wave length is half of the upstream frequency. This characteristics of the high frequency solution is found to be caused by the strong interaction between unsteady vortices. This strong interaction also leads to destroy of the upstream wake strips inside the viscous sublayer as well as the buffer layer.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.4
• /
• pp.1-11
• /
• 2004

Numerical analyses on the aerodynamic characteristics of a counter rotating axial flow fan were conducted for the development of an axial type in-line duct fan. The counter rotating fan has a front rotor and a rear rotor which are counter rotating each other. Blade design of the counter rotating fan was done by extension of design method for axial flow fan which consists of rotor and stator blades. Through flow analysis was performed using matrix method which is applied for flow fields prediction of compressors or turbines. Aerodynamic characteristics and characteristic curves of the counter rotating fan were analyzed by expansion of the frequency domain panel method with duct modeling. Pressure losses were higher at leading edge and hub region of rotor blades. Characteristic curve of the counter rotating fan was overpredicted without consideration of viscous effect.

• Wind and Structures
• /
• v.15 no.6
• /
• pp.481-494
• /
• 2012

The greenhouse type metal structures are increasingly used in modern construction of livestock farms because they are less laborious to construct and they provide a more favorable microclimate for the growth of animals compared to conventional livestock structures. A key stress factor for metal structures is the wind. The external pressure coefficient ($c_{pe}$) is used for the calculation of the wind effect on the structures. A high pressure coefficient value leads to an increase of the construction weight and subsequently to an increase in the construction cost. The EC1 in conjunction with EN 13031-1:2001, which is specialized for greenhouses, gives values for this coefficient. This value must satisfy two requirements: the safety of the structure and a reduced construction cost. In this paper, the Navier - Stokes and continuity equations are solved numerically with the finite element method (Galerkin Method) in order to simulate the two dimensional, incompressible, viscous air flow over the vaulted roofs of single span and twin-span with eaves livestock greenhouses' structures, with a height of 4.5 meters and with length of span of 9.6 and 14 m. The simulation was carried out in a wind tunnel. The numerical results of pressure coefficients, as well as, the distribution of them are presented and compared with data from Eurocodes for wind actions (EC1, EN 13031-1:2001). The results of the numerical experiment were close to the values given by the Eurocodes mainly on the leeward area of the roof while on the windward area a further segmentation is suggested.

• Earthquakes and Structures
• /
• v.18 no.2
• /
• pp.215-222
• /
• 2020

In this paper, slit steel rubber bearing is presented as an innovative seismic isolator device. In this type of isolator, slit steel damper is an energy dissipation device. Its advantages in comparison with that of the lead rubber bearing are its simplicity in manufacturing process and replacement of its yielding parts. Also, slit steel rubber bearing has the same ability to dissipate energy with smaller value of displacement. Using finite element method in ABAQUS software, a parametric study is done on the performance of this bearing. Three different kinds of isolator with three different values of strut width, 9, 12 and 15 mm, three values of thickness, 4, 6 and 8 mm and two steel types with different yield stress are assessed. Effects of these parameters on the performance characteristics of slit steel rubber bearing are studied. It is shown that by decreasing the thickness and strut width and by selecting the material with lower yield stress, values of effective stiffness, energy dissipation capacity and lateral force in the isolator reduce but equivalent viscous damping is not affected significantly. Thus, by choosing appropriate values for thickness, strut width and slit steel damper yield stress, an isolator with the desired behavior can be achieved. Finally, the performance of an 8-storey frame with the proposed isolator is compared with the same frame equipped with LRB. Results show that SSRB is successful in base shear reduction of structure in a different way from LRB.