• 한국소음진동공학회논문집
• /
• 제23권2호
• /
• pp.176-184
• /
• 2013

Quantification of road noise is a challenging issue in the development of tire noise since its transfer paths are complicated. In this paper, a simplified model to estimate the road noise is developed. Transfer path of the model is from wheel to interior. The method uses the wheel excitation force estimated throughout inverse method. In inversion procedure, the Tikhonov regularization method is used to reduce the inversion error. To estimate the wheel excitation force, the vibration of knuckle is measured and transfer function between knuckle and wheel center is also measured. The wheel excitation force is estimated by using the measured knuckle vibration and the inversed transfer function. Finally interior noise due to wheel force is estimated by multiplying wheel excitation force in the vibro-acoustic transfer function. This vibro-acoustic transfer function is obtained throughout measurement. The proposed method is validated by using cleat excitation method. Finally, it is applied to the estimation of interior noise of the vehicle with different types of tires during driving test.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.197-202
• /
• 2006

The low-altitude earth observation satellite is generally equipped with high performance camera as a main payload which is vulnerable to vibration environment. During the launch process of a satellite, the combustion and jet noise of launch vehicle produce severe acoustic environment and the acoustic loads induced may damage the critical equipments of the satellite including the camera. Therefore to predict and simulate the effect of the acoustic environment which the satellite has to sustain at the lift-off event is very important process to support the load-resistive design and test-qualification of components. Statistical Energy Analysis(SEA) has been widely used to estimate the vibro-acoustic responses of the structures and gives statistical but reliable results in the higher frequency region with less modeling efforts and calculation time than the standard FEA. In this study, SEA technique has been applied to a 3-Dimensional model of a low-altitude earth observation satellite to predict the acceleration responses on the structural components induced by the high level acoustic field in the launch vehicle fairing. In addition, the expected response on each critical component panel was calculated by the classical method in consideration of the mass loading and imposed sound pressure level, and then compared with SEA results.

• 한국정밀공학회지
• /
• 제25권12호
• /
• pp.117-124
• /
• 2008

In early design stage, the simulation of interior noise is useful for the enhancement of the noise, vibration and harshness (NVH) performance in a vehicle. The traditional transfer path analysis (TPA) technology cannot simulate the interior noise since it uses the experimental method. In order to solve this problem, in this paper, the hybrid TPA is developed as the novel approach. The hybrid TPA uses the simulated excitation force as the input force, which excites the flexible body of a car at the mount point, while the traditional TPA uses the measured force. This simulated force is obtained by numerical analysis for the FE (finite element) model of a powertrain. The interior noise is predicted by multiplying the simulated force by the vibro-acoustic transfer function (VATF) of the vehicle. The VATF is the acoustic response in the compartment of a car to the input force at the mount point of the powertrain in the flexible car body. The trend of the predicted interior noise based on the hybrid TPA very well corresponds to the measured interior noise, although there is some difference due to not only the experimental error and the simulation error but also the effect of the air-borne path.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.563-564
• /
• 2014

Recent developments in the prediction of the contribution of windnoise to the interior SPL have opened a realm of new possibilities in terms of i) how the convective and acoustic sources terms can be identified, ii) how the interaction between the source terms and the side glass can be described and finally iii) how the transfer path from the sources to the interior of the vehicle can be modelled. This work discusses several simulation methods that can be used to represent the physical phenomena involved such as CFD, FEM, BEM, FE/SEA Coupled and SEA. This work focuses on the validation of the wind noise source characterization method and the vibro-acoustic models on which the wind noise sources are applied in the framework of a benchmark proposed by Hyundai Motors Corporation.

• 한국소음진동공학회논문집
• /
• 제19권1호
• /
• pp.42-49
• /
• 2009

In this paper, an alternative method was introduced to conduct a transfer path analysis for airborne noise. The method used the transfer function matrix composed of acoustic transfer functions that are referenced by the input voltage of a calibration source. A calibration factor which is converting a virtual voltage to source strength was deduced by vibro-acoustical reciprocity theorem. The calibration factor is then multiplied to the virtual input voltage to estimate the operational source strength. Three loudspeakers were used to noise sources of acrylic half car model. The method was applied to airborne noise transfer path analysis of the half car. The estimated source strength by transfer path analysis was compared the deduced source strength by vibro-acoustical reciprocity to verify the method.

• 한국음향학회지
• /
• 제21권8호
• /
• pp.708-718
• /
• 2002

본 연구에서는 진동-음향계에서 방사되어 생성된 일반 근접장에서 음향 인텐시티 기법을 이용해 소음원을 파악하는 방법의 문제점에 관하여 논한다. 이를 위해 자동차나중장비의 엔진실을 모사하는 3차원 구조물 모델을 고려한다. 실제 상황과 유사하도록 모델에는 음원들이 복잡한 형상의 표면에 상호 연관성이 있는 또는 없는 형태로 분포한다. 즉, 음원들은 음향학적으로 단단한 상자들에 의해 형성된 좁은 공간으로 연결되어 있다. 따라서 반사가 심한 음장에 면한 표면에 배치되어 있으며, 전체 구조의 바닥 부분은 하부의 바닥과 작은 틈새만큼 떨어져 있다. 음향 경계요소법을 이용하여 근접 음장과 내부 음장의 인텐시티를 계산한다. 주어진 음원들간의 상대적 위상, 주파수, 위치에 따른 효과를 조사하였고, 그 결과를 등인텐시티선도, 벡터도 및 에너지 유선으로 표현하였다. 현장에서 종종 행해지는 바와 같이, 예를들어 엔진룸 상부에서 인텐시티를 측정하여 음원을 조사하는 것과 같은, 반사장이 강한 음장에서 음향 인텐시티 기법을 적용하여 음원탐색을 시도할 경우 가짜 음원이 검색될 수 있음을 보였다. 이와 같은 음장에서 정확한 결과를 얻기 위해서는, 음원탐색 수행 전에 음장의 리액티비티에 대한 조사가 먼저 필요하며, 측정을 시행하기 전에 음장의 리액티비티를 없애거나 대폭적으로 줄이는 작업이 선행되어야 할 것이다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.318-321
• /
• 2005

In vibro-acoustic analysis, the commercial CAE tools, such as SYSNOISE, is usually used to take into account of the coupled effects of fluid acoustics and structural vibration. The acoustic field can be solved by either FEM or BEM, while the vibration field is usually solved by FEM. The interior or exterior acoustic problems with the coupled effects of the structural boundary could be solved by the commercial tools. The commercial tools, however, could not solve the problems in case that both the interior and exterior acoustic field is coupled with the structural boundary. In this paper, a realistic method based on FEM/BEM coupling scheme is presented to analyze the acoustic radiation from the internal source in a chamber to external acoustic field through elastic structural boundary. Several numerical examples are implemented to validate the developed program.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.721-724
• /
• 2005

With the advantages of large vibration energy dissipation of structures, the granular materials are used as vibration and acoustic treatments. In this case of vibro acoustic controls, a finite dynamic strength of the solid component (frame) is an important design factor. The dynamic stiffness of hollow cylindrical beams containing porous and granular materials as damping treatment was measured. Using the Rayleigh-Ritz method, the effects of damping materials on the dynamic characteristics of beams were investigated. The results suggested that the acoustic structure Interaction between the frame and the structure enhances the dissipation of the vibration energy significantly. The same methods were applied also to vibration control of sandwich panels. By filling the cavities of honeycomb cores using unconsolidated granular materials, its sound transmission toss was improved significantly.

• 소음진동
• /
• 제8권2호
• /
• pp.274-282
• /
• 1998

A systematic procedure for designing a direct-radiator-type loudspeaker has been developed, based on the numerical vibro-acoustic analysis and the Taguchi method. The finite-element model of the speaker cone has been used to calculated the vibration response of the cone excited by the voice coil. The vibration displacement of the speaker cone has been converted into the vibration velocity and used as a boundary condition for the acoustic analysis. The acoustic frequency characteristics of the loudspeaker have been calculated by the boundary element method. The numerical results have been verified by the experiments carried out in an anechoic chamber. Some design parameters have been selected by using the Taguchi method, and the variations of the acoustic characteristics due to the changes of the parameter values have been examined using the numerical model.

• 한국음향학회:학술대회논문집
• /
• 한국음향학회 1999년도 학술발표대회 논문집 제18권 1호
• /
• pp.293-296
• /
• 1999