• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.32 no.5
• /
• pp.285-295
• /
• 2020

In the case of small observation towers located at sea, it is necessary to confirm the change in dynamic characteristics due to the influence of environmental loads. In this study, the dynamic characteristics were analyzed and the numerical analysis model was designed through field dynamic response measurement on the Mangyeong Offshore Observation Tower (Mangyeong Tower) located near the Saemangeum Embankment. As a result of the measurement, the natural frequency was found to increase slowly as the tide level is lowered. In addition, it was confirmed that the same mode has two frequencies, which was judged to be a phenomenon in which the natural frequency was partially increased when the pile and the ground contacted by scouring. For numerical analysis, the upper mass, artificial fixity point, scour depth and fluid influences are reflected in the structural characteristics of the Mangyeong Tower. In addition, the model updating from the estimated natural frequency and pattern search algorithm was performed. From the model updating, it is expected that it can be applied to future studies on stability of Mangyeong Tower.

• Geophysics and Geophysical Exploration
• /
• v.11 no.2
• /
• pp.137-147
• /
• 2008

Fault rupture directivity of the Odaesan earthquake, which was inferred to be the main cause of the high PGAvalue (> 0.1 g) unusually observed at the near-source region, was analyzed by using the data from the nearby (R < 100 km) dense seismic stations. The Boatwright's method (2007) was adopted for this purpose in which the azimuth and takeoff angle of the unilateral rupture directivity function could be estimated based on the relative peak ground-motions of seismic stations resulting from the nature of the rupture directivity. In this study, the approximate values of the relative peak ground-motions was derived from the difference between the log residuals of the point-source spectral model (Boore, 2003) for the main and secondary events based on the Random Vibration Theory. In this derivation, the spectral difference for a frequency range between the source corner frequencies of main and secondary events was considered to reflect only the effect of the fault directivity. The inversion result of the model parameters for the fault directivity function showed that the fault-plane of NWW-SEE direction dipping steeply to the North with high rupture velocity near upward in SE direction is responsible for the observed high level of ground-motion at the near-source region.

• Journal of the Korean Chemical Society
• /
• v.19 no.2
• /
• pp.92-97
• /
• 1975

The molecular and electronic structures of $TiCl(OC_6H_5)_3{\cdot}C_6H_5OH\;and\;Ti(OC_6H_5)_4{\cdot}C_6H_5OH$ have been studied by employing cryoscopic and electronic spectroscopic methods. The cryoscopic data have shown that the dimeric tetraphenoxytitanium(Ⅳ) phenolate in solid undergoes complete dissociation into monomer in solution and also the chlorocomplex starts dissociation around the concentration of 8 m mole/l. Therefore, these two Ti-complexes are pentacoordinated in dilute solution and the local symmetry of the titanium ion in these complexes seems to be trigonalbipyramid. The electronic spectra of $TiCl(OC_6H_5)_3{\cdot}C_6H_5OH$ and $Ti(OC_6H_5)_4{\cdot}C_6H_5OH$ each show two band, systems, one vibration-structural band characteristic of the aromatic ring in the near UV and another visible band at 26.8 kK, 29.6 kK, respectively, which are assigned as a ligand to metal charge transfer band corresponding to $^1A_1''{\to}^1E'\;or\;^1E''$ transition.

• Journal of the Korean Vacuum Society
• /
• v.19 no.4
• /
• pp.249-255
• /
• 2010

Methods of the characteristics evaluation of turbo-molecular pumps (TMP) are well-defined in the international measurement standards such as ISO, PNEUROP, DIN, JIS, and AVS. The Vacuum Center in the Korea Research Institute of Standards and Science (KRISS) has recently designed, constructed, and established the integrated characteristics evaluation system of TMPs based on the international documents by continuously pursuing and acquiring the reliable international credibility through measurement perfection. The measurement of TMP pumping speed is normally performed with the throughput and orifice methods dependent on the mass flow regions. However, in the UHV range of the molecular flow region, the high uncertainties of the gauges, mass flow rates, and conductance are too critical to precisely accumulate reliable data. In order to solve the uncertainty problems of pumping speeds in the UHV range, we introduced a SRG with 1% accuracy and a constant volume flow meter (CVFM) to measure the finite mass flow rates down to $10^{-1}$ Pa-L/s with 3% uncertainty for the throughput method. In this way we have performed the measurement of pumping speed down to $10^{-4}$ Pa with an uncertainty of less than 6% for a 1000 L/s TMP. In this article we suggest that the CVFM has an ability to measure the conductance of the orifice experimentally with flowing the known mass through the orifice chambers, so that we may overcome the discontinuity problem encountering during introducing two measurement methods in one pumping speed evaluation sequence.

• Research in Community and Public Health Nursing
• /
• v.6 no.2
• /
• pp.319-334
• /
• 1995

To investigate the risk factors of low back pain, an epidemiological study was carried out among male workers aged 20-55 employed in an automobile industry in Korea during the time period from February 1993 to October 1995. Workers participated to this study were divided into low back pain group(LBP) and control group, according to the self-reports by written questionnaires. General characteristics, medical history, work related factors, fatigue, and MMPI were compared between two groups. To clarify the relationship between job related low back pain and radiologic features of lumbar spine, radiographic study was carried out. The resultant data were processed for $x^2-test$, t-test, and stepwise logistic regression to confirm the adjusted odds ratios. The results were as follows: 1. History of back disease, lifting and carrying work, excessive physical fatigue, and weakend back strength of individual workers were directly associated with low back pain. Odd ratios of these 4 risk factors of low back pain were 5.07, 3.34, 1.49, and 1.22 respectively. 2. The frequency of low back pain history was significantly higher in LBP group. 3. Back muscle strength of lumbar spine of LBP group were significantly lower than control group. 4. The workers in LBP group revealed high fatigue symptoms. 5. In MMPI test LBP group showed higher scales in hypochondriasis, depression, hysteria, psychopathic deviate, paranoia, psychasthenia, schizophrenia, and hypomania. 6. LBP group were more frequently involved in lifting and carrying, working in awkward position, bending, twisting and using lower extremities. 7. LBP group were exposed more to vibration during working. 8. In the Analysis of radiographs of lumbar spine, Jacob's line not crossing fourth lumhar disc space, transitional vertebrae and lumbar displacement more than 4.4mm in standing lateral view were more frequently observed in LBP group than control group. Through these results, it is concluded that identification of previous history of back problem, change of work or working environment for workers with previous back problem and measures to relieve both physical and psychological fatigue of the workers are required for optimal management of work-related back problems among workers. In the present study, several results were different from the previous reports: Jacob's line not corssing fourth lumbar disc space, lumbarization, and vertebral slipping (spondylolisthesis) more than 4.4mm are related to backache. Meticulous studies are required to elucidate the difference.

• KEPCO Journal on Electric Power and Energy
• /
• v.1 no.1
• /
• pp.181-188
• /
• 2015

The non-contact permanent magnet gear has advantages of high efficiency and improved reliability. It has other advantages of no mechanical friction loss, very little noise and vibration, and no need for lubricant. With these advantages, the non-contact permanent magnet gear that solves the physical contact problem of the mechanical gear has drawn attention. Due to this unique non-contact characteristic, the non-contact permanent magnet gear which is capable of non-contact torque transmission has replaced mechanical gear. The mechanical gears which is in many fields of the modern industry, is used mostly for power transmitting mechanical devices. However, it also has the problem of a low torque density, which requires improvement. In this paper, a novel pole piece shape is proposed in order to improve the problem of low torque density of the non-contact permanent magnet gear. The experiment data required for predicting the relationships among them are obtained using finiteelement Operating method based on two-dimensional (2-D) numerical analysis. Therefore, this paper derived an optimal model for thenon-contact permanent magnet gear with the novel pole piece using the Box-Behnken design, and the validity of the optimal design of the proposed pole piece shape through variance analysis and regression analysis demonstrated. In this paper, we performed the thransfer torque analysis in order to improve the torque density and power density, we have performed on optimal design of proposed pole piece shape using box-behnken.

• The KIPS Transactions:PartB
• /
• v.18B no.3
• /
• pp.147-156
• /
• 2011

This paper proposes a 3-stage (preprocessing, feature extraction, and classification) fault detection and classification algorithm for induction motors. In the first stage, a low-pass filter is used to remove noise components in the fault signal. In the second stage, a discrete cosine transform (DCT) and a statistical method are used to extract features of the fault signal. Finally, a back propagation neural network (BPNN) method is applied to classify the fault signal. To evaluate the performance of the proposed algorithm, we used one second long normal/abnormal vibration signals of an induction motor sampled at 8kHz. Experimental results showed that the proposed algorithm achieves about 100% accuracy in fault classification, and it provides 50% improved accuracy when compared to the existing fault detection algorithm using a cross-covariance method. In a real-world data acquisition environment, unnecessary noise components are usually included to the real signal. Thus, we conducted an additional simulation to evaluate how well the proposed algorithm classifies the fault signals in a circumstance where a white Gaussian noise is inserted into the fault signals. The simulation results showed that the proposed algorithm achieves over 98% accuracy in fault classification. Moreover, we developed a testbed system including a TI's DSP (digital signal processor) to implement and verify the functionality of the proposed algorithm.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.6
• /
• pp.148-156
• /
• 2018

The integrity assessment of the bridge behavior is generalized by field data of a static load-deformation curve and dynamic properties such as impact factors and natural frequencies. Evaluating it with numerical analysis is a reasonable method. The results of the mockup test and the numerical analysis are corresponded with each other since the behavior of service load proceeds in elastic region. In case of the dynamic behavior of structure, especially for the analysis of vibration, the result of the mockup test differs from the result of numerical analysis a little due to the geometric shape and non-homogeneous materials. In order to converge on these tolerances, this study suggested several numerical models, analyzed the sensitivity and finally offered a practical modeling method for the estimation of bridge on the basis of the result of mockup test. Based on the model substituted concrete section for strands section, the natural frequency of the model composed with axial stiffness of strands or the model applied the modified modulus of elasticity was closest with the result of the mockup test.

• Journal of Navigation and Port Research
• /
• v.37 no.6
• /
• pp.575-580
• /
• 2013

The IMU(Inertial Measurement Unit) which is the expensive equipment has been used as a special limited area, usually in measurement of posture of applying to the areas of ship, submarine, aircraft and military equipment application. However, in the current situation, MEMS AHRS technology can replace the high-priced IMU in MEMS AHRS selected application field. In this paper, wireless hull motion measurement system was suggested for measuring key elements of ship's movement such as rolling, pitching and yawing using gyro, acceleration and magnetic sensors of AHRS. In order to reduce the error such as instantaneous acceleration, effects and vibration of geomagnetic, we have adopted the sensors equipped with Kalman filtering. The Wireless hull motion measurement system using AHRS sensors was tested in actual ship and it could easily be applied in limited installation circumstances of the ship. In the future, this system can be useful in the navigation safety and marine accident analysis by using with ship equipment such as INS or VDR in the maritime.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.4
• /
• pp.305-312
• /
• 2007

Among many types of light rail transits (LRT), the rubber-tired automated guide-way transit (AGT) is prevalent in many countries due to its advantages such as good acceleration/deceleration performance, high climb capacity, and reduction of noise and vibration. However, AGT is generally powered by high-voltage electric power feeding system and it may cause electromagnetic interference (EMI) to measurement sensors. The fiber optic sensor system is free from EMI and has been successfully applied in many applications of civil engineering. Especially, fiber Bragg grating (FBG) sensors are the most widely used because of their excellent multiplexing capabilities. This paper investigates a prestressed concrete girder bridge in the Korean AGT test track using FBG based sensors to monitor the dynamic response at various vehicle speeds. The serviceability requirements provided in the specification are also compared against the measured results. The results show that the measured data from FBG based sensors are free from EMI though electric sensors are not, especially in the case of electric strain gauge. It is expected that the FBG sensing system can be effectively applied to the LRT railway bridges that suffered from EMI.