• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.2 no.1
• /
• pp.1-10
• /
• 1990

In the present study, the entrance length, velocity profiles and waveforms of developing transitional steady flows in a square duct are investigated analytically and experimentally. The systems of conservation equations for transitional steady duct flows are solved analytically by linearizing non-linear convective terms and adoption of modified eddy viscosity from empirical correlations. Analytical solutions of velocity profiles for developing transitional steady flow were obtained in the form of infinite series. The experimental study for transitional steady flow in a square duct with $40mm{\times}40mm{\times}4000mm$($width{\times}height{\times}length$) was carried out to measure velocity profiles and other parameters by using a hot-wire anemometer with data acquisition and processing system. The entrance length of developing transitional steady flows in a square duct was $L_e{\fallingdotseq}0.02{\cdot}Re,st{\cdot}D_h$, and the overshoot was occured at about 30 times of hydraulic diameter because of the effect of external velocity of boundary layer and instantaneous acceleration.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.2
• /
• pp.673-676
• /
• 2005

In this paper, we propose a improved control performance for autonomous mobile robot using the embeded system. The proposed PID(PPID) control method removes steady state error, and has good performance in transient response. The integral term in the proposed method accumulates error in increment section, inverses errors in decrement section, and increases the effect of integral coefficient around target. Therefore, the PPID control method decreases the overshoot, and makes settling time faster than general PID(GPID) control method. In order to verify the effectiveness of the proposed method(PPID), we simulated the position control of DC motor, and experimented the velocity control of autonomous mobile robot. The PPID control method demonstrated good control performance that decrease overshoot and settling time in simulation and experiments.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.11 no.1
• /
• pp.65-70
• /
• 2011

The increased disk rotational velocity to improve the data transfer rate has raised up many serious problems in its servo control system which should control the position and velocity of a spot relative to a rotating disk. This paper proposes gain-scheduling-based track-seek control for single stage actuator of hard disk drives. Gain scheduling is a technique that can extend the validity of the linearization approach to a range of operating points and one of the most popular approaches to nonlinear control design. The proposed method schedules controller gains to improve the transient response and minimize overshoot during the functions of the read/write head positioning servomechanism for the seek control. The validity of the proposed method is demonstrated through stability analysis and simulation results.

• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.6
• /
• pp.760-769
• /
• 2006

This paper proposes an autopilot system using a fuzzy PID controller to satisfy performances required for the automatic navigation of ships under various marine circumstances. The existing autopilot system using a PD type controller has difficulties in eliminating a steady-state error and compensating nonlinear characteristics of ships. The autopilot system using the proposed fuzzy PID controller has a self-tuning ability, an ability to compensate nonlinear characteristics, and an ability to turn at constant angular velocity. Therefore. it can naturally make a steady-state error zero, compensate nonlinear dynamic effect of ships, have an adaptability to parameter variation owing to shallow water effect, and have an ability to turn ship's course rapidly without overshoot through procedures of acceleration, constant, and deceleration of angular velocity for large course-changing.

• Electrical & Electronic Materials
• /
• v.9 no.6
• /
• pp.564-571
• /
• 1996

We calculated the drift-velocities of electrons and holes of I $n_{0.53}$(A $l_{x}$G $a_{1-x}$ )$_{0.47}$As, which is used for semiconductor materials of high performance HBTs, along with the various doping concentrations and Al mole fractions as well as the electric fields by Monte Carlo experiment. Especially, for the valence bands the accuracy of hole-drift-velocity was improved in the consideration of intervalley scattering due to the inelastic scattering of acoustic phonon. From the results the empirical formulas of the low- and high field mobility of electrons and holes were extracted by using nonlinear least square fitting method. The accuracy of the formulas was proved by comparing the formula of low-field electron mobility as well as drift-velocity of I $n_{0.53}$ G $a_{0.47}$As and of low-field hole mobility of GaAs with the measured values, where the error was below 10%. For the high-field mobilities of electron and hole the results calculated by the formulas were very well matched with the MC experimental results except at the narrow field range where the electrons produced the velocity overshoot and the corresponding error was about 30%.0%. 30%.0%.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.3
• /
• pp.191-201
• /
• 1997

Accurate positioning of a throttle valve is required to implement the traction control system(TCS) which improves acceleration performance in slippery roads. In this research, position control system is developed for the main throttle actuator(MTA) system which uses one throttle actuation for small volume and DC servo motor for fast response. In order to drive DC motor, PWM signal generator and PWM amplifier were built and interfaced to the motor and controller. Digital PID control law is used as basic control algorithm. In order to prevent overshoot and improve accuracy, velocity profiles are generated and implemented whenever the targer throttle angle is given from the TCS controller. Thanks to velocity profiles, the control performance was very good and only one set of PID gains was used to cover the entire operating range. Also, the resolution of position is about 0.4$^{\circ}C$, which is better than that of stepping motor also used as throttle actuator in some products. The response time of the developed system is also fast enough to implement the engine control based TCS algorithm.

• International Journal of Automotive Technology
• /
• v.6 no.6
• /
• pp.615-623
• /
• 2005

In this research, an effective technique was examined to improve the drift running performance. Concretely, the driver model by which the counter steer was done was assumed to the model by which the vehicle body slip angle (and the vehicle body slip angle velocity) was feed back. Next, the effectiveness of the system which added the assist steer angle corresponding to the steering wheel angle velocity to a front wheel steer angle was clarified as a drift running performance improvement technique of the vehicle. As a result, because the phase advances when the differentiation steer assistance is added, it has been understood to be able to cover the delay of the counter steer when the drift running. Therefore, it has been understood that the drift control does considerably easily. Moreover, it has been understood that the differentiation steer assistance acts effectively at the drift cornering by which the drift angle is maintained in cornering and the severe lane change with a drift at a situation. That is, it was understood to be able to settle to the drift angle of the aim quickly at the time of the drift cornering because the delay of the control steer angle of the counter steer was improved. Moreover, it was understood for the transient overshoot of the vehicle tracks to be able to decrease, and to return to the state of stability quickly at the severe lane change.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.6
• /
• pp.919-925
• /
• 2023

Modern drones are equipped with miniaturized mission equipment capable of performing various tasks such as surveillance and reconnaissance. Consequently, these mission equipment are exposed to disturbances like wind loads and motor rotations, which can lead to instability in the operation of the Electro-Optical Targeting System (EOTS). Specifically, simple step inputs for changing the line of sight in EOTS can cause abrupt changes in speed, inducing overshoot and potentially creating instability along with other disturbances. To address this, a velocity profile was designed so that the angular velocity moves in a trapezoidal shape when changing the EOTS line of sight. A Double-loop controller was designed to apply this profile as an input to the external loop receiving position feedback. The system's stability was then compared, and the velocity profile was optimized within a stable range by varying maximum speed and acceleration.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.307-311
• /
• 2003

2-mass system is generally used as controller of the variable-speed to transfer electromotion power to mechanical load such as industrial robot, driving parts of electric vehicle, rolling machine system of steel plant and driving parts of elevator. In this case, PI controller is often used as a velocity controller because of simplicity of system. But PI control algorithm is not enough for obtaining the control characteristics required for this system. To solve this problem, 2-mass system based on the PID controller derives the optimum PID parameters by pole assignment and estimation of the ITAE performance index. In this case, the system have tenacious properties about disturbance, but it causes extreme overshoot and vibration because of rapidly output of controller in early transient response about desired value. And if speed control system is applied by 2-DOF parameter ${\alpha}$, a temporary value, we must induce most suitable parameter by complicate pole assignment and estimation of the ITAE performance index whenever ${\alpha}$ changes. In this paper, to solve this problem we suggest control algorithm to followed exactly value of ${\alpha}$ as 2-DOF parameter by using fuzzy algorithm . So, intelligence algorithm modeled by human knowledge, experience, teachability and judgment follow exact ${\alpha}$ value and it can compose the efficient 2-DOF PID controller to improve following performance, overshoot decrease.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.56 no.2
• /
• pp.172-182
• /
• 2020

In order to offer specific information needed to assist in operation of a ship with same type rudder through evaluating the maneuverability of training ship A-Ra with flapped rudder, sea trials based full scale for turning test, zig-zag test with rudder angle 10° and 20°, and spiral test at service condition were carried out on starboard and port sides around Jeju Island according to the standards of maneuverability of IMO. As a result, the angular velocity of port turn was higher than that of starboard turn. Therefore, the size of turning circle was longer on the starboard side. In addition, variation of the transfer due to various factors was more stable than those of the others. In the Z-test results, the mean of 1st and 2nd overshoot angles were 9.8°, 6.3° and 15.3°, 9.2° respectively when the port and starboard was 10°; the 1st overshoot angle were 18°, 13.7° when using 20°. Her maneuverability index T' and K' can be easily determined by using a computer with the data obtained from Z-test where K' and T' are dimensionless constants representing turning ability and responsiveness to the helm, respectively. In the Z-test under flap rudder angle 10°, the obtained K' value covered the range of 2.37-2.87 and T' was 1.74-3.45. Under the flap rudder angle 20°, K' and T' value showed 1.43-1.63, 1.0-1.73, respectively. In the spiral test, the loop width was unstable at +0.3° and -0.5°-0.9° around the midship of flap rudder. As a result, course stability was comparatively good. From the sea trial results, training ship ARA met the present criterion in the standards of maneuverability of IMO.