• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.5
• /
• pp.643-651
• /
• 1998

Turbulent unsteady flows in the entrance region of a square duct are investigated with a hot-wire anemometer system. The velocity waveforms the mean and turbulence components of the axial velocity and the entrance length are obtained as a major characteristics of the developing turbulent unsteady flows. An inviscid flow theory is presented to describe the developing axial mean velocity profiles. A good agreement is seen between the measured and theoretically predicted values. The propagation of turbulence generated near the entrance of the square duct is satisfactorily approximated by an empirical correlation of the propagation of turbulence proposed so far. The local turbulence intensi-ty is found to be a little smaller in the accelerating phase than in the decelerating phase. The entrance length is about 60 times as large the hydraulic diameter.

• Tribology and Lubricants
• /
• v.24 no.6
• /
• pp.343-348
• /
• 2008

In this paper, a CFD (Computational fluid dynamics) code, FLUENT is adopted to investigate accurate flow characteristics for a slipper bearing which is used swash plate type hydraulic axial piston pump. Static pressure and velocity distributions, and velocity vectors are plotted for different film thickness and slipper rotational velocity. In recess region, there exists a doughnut shaped vortex ring. The static pressure distributions are non-uniform and the flow fields are highly asymmetrical under bearing rotation. Therefore the numerical method adopted in this paper can be use in design of hydrostatic components and further studies are required.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.7 s.238
• /
• pp.837-845
• /
• 2005

In this paper, an investigation on high-Schmidt number (Sc=1670) mass transfer in turbulent flow around a rotating circular cylinder is carried out by Direct Numerical Simulation. The concentration field is computed for three different values of low Reynolds number, namely 161, 348 and 623 based on the cylinder radius and friction velocity. Statistical study reveals that the thickness of Nernst diffusive layer is very small compared with that of viscous sub-layer in the case of high Sc mass transfer. Strong correlation of concentration field with streamwise and vertical velocity components is observed. However, that is not the case with the spanwise velocity component. Instantaneous concentration visualization reveals that the length scale of concentration fluctuation typically decreases as Reynolds number increases. Statistical correlation between Sherwood number and Reynolds number is consistent with other experiments currently available.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.10a
• /
• pp.315-317
• /
• 2008

The purpose of this study is to confirm the possibility of wind power generation by a vehicle-induced at the median strip on highway. In order to find out wind field information, a CFD method was used. According to the simulation results, the x, y, z-component of the wind velocity around a median strip are rapidly changed at near before and behind a moving vehicle. The x-component of the wind velocity appears high within the range of the length of the passing vehicle, and the wind direction appeared in the opposite direction at the behind of a vehicle. However, x and y-components of the wind velocity at the behind of vehicle are shown constantly. We confirmed possibility of wind power generation using a vehicle-induced wind at the median strip.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.185-191
• /
• 2001

In many papers, the powertrain system generally has been madeled as one-dimensional torque model. One-dimensional powertrain model may calculate the torque correctly but it does not consider the non-rotational degrees-of-freedom of the powertrain components and the interaction of these degrees-of-freedom with the vehicle body frame and suspension. To consider the non-rotational degrees of freedom, the differential is modeled as a three-dimensional rigid body in this paper. A constant velocity joint is newly formulated and a relative constraint is also formulated to model the motion transfer due to gear ratio of the differential. Implementing the proposed powertrain system in the multibody model, more detail dynamic responses can be obtained. Obtained outputs such as reaction torques on the constant velocity joint and reaction forces on the rack can be useful data in the design of a powertrain.

• ETRI Journal
• /
• v.32 no.1
• /
• pp.68-72
• /
• 2010

The coupling between the transverse and longitudinal components of the channel electron motion in NMOS devices leads to a reduction in the barrier height. Therefore, this study theoretically investigates the effects of the in-plane velocity of channel electrons on the capacitance-voltage characteristics of nano NMOS devices under inversion bias. Numerical calculation via a self-consistent solution to the coupled Schrodinger equation and Poisson equation is used in the investigation. The results demonstrate that such a coupling largely affects capacitance-voltage characteristic when the in-plane velocity of channel electrons is high. The ballistic transport ensures a high in-plane momentum. It suggests that such a coupling should be considered in the quantum capacitance-voltage modeling in ballistic transport devices.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1789-1794
• /
• 2004

The present study investigates flow characteristics in an optical disc drive. Detailed knowledge of the flow characteristics is essential to analyze flow-induced noise and vibration, forced convection and flow friction loss. The ODD used in the personal computer is used for the experiment and rotating velocity of disc is under the 4500 rpm. Time-resolved velocity components and velocity spectrum are obtained using the laser Doppler anemometry (LDA). The results show that the front holes reduce now-induced noise and the position of pickup body affects flow near the window. In addition, il is possible for cooling of heat sources in an optical disc drive through measuring the flow fields under the tray.

• 유체기계공업학회:학술대회논문집
• /
• 1999.12a
• /
• pp.227-233
• /
• 1999

Detailed Measurements were made to investigate the turbulence characteristics of a leakage vortex in an axial-flow fan using three-dimensional LDV. The turbulence in the leakage vortex has highly anisotropic characteristics with the radial value being the maximum. The turbulence intensity components in the vortex in the streamwise and tangential directions increase up to a certain downstrean position and then decrease. This increase is mainly due to the rapid decrease of the streamwise velocity of the vortex and partly due to the radial gradient of the streamwise velocity caused by a velocity deficit. As the vortex decays moving downstream, turbulence intensity also decrease gradually.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.2
• /
• pp.302-312
• /
• 1992

Three dimensional velocity measurements of a 35.deg. inclined jet issuing into turbulent boundary layer on both concave and convex surfaces have been conducted. To investigate solely the effect of each curvature on the flow field, streamwise pressure variations are minimized by adjusting the shape of the opposite wall in the curved region. From the measured velocity components, streamwise mean vorticities are calculated to determine jet-crossflow interface. The results on convex surface show that the injected jet is separated from the wall and the bound vortex maintains its structure far downstream. On concave surface, the secondary flow in the jet cross-sections are enhanced and in some downstream region from the jet exit, the flow on the concave surface has been developed to Taylor-Gortler vortices

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.1
• /
• pp.98-108
• /
• 2004

This study concerns a large eddy simulation (LES) of turbulent flow around a bluff body inside a sudden expansion cylindrical chamber, a configuration which resembles a premixed gas turbine combustor The simulation code is constructed by using the general coordinate system based on the physical contravariant velocity components. The Smagorinsky model is employed and the calculated Reynolds number is 5,000 based on the bulk velocity and the diameter of the inlet pipe. The combined grid technique and cylindrical grid are tested in the numerical simulation with complex geometry. The predicted turbulent statistics are evaluated by comparing with LDV measurement data. The numerical flow visualizations depict the behavior of turbulent mixing process behind the flame holder.