• Journal of the Korea Institute of Military Science and Technology
• /
• v.19 no.4
• /
• pp.551-558
• /
• 2016

We analyzed wind speed over South Korea for HALE UAV(High Altitude Long Endurance Unmaned Aerial Vehicle) flight safety. Annual variation of wind speed at 200 hPa showed that winter season was stronger than summer. According to latitude, wind speeds in January and August were found to be $52{\sim}74m\;s^{-1}$ and $15{\sim}26m\;s^{-1}$, respectively. Wind speed was stronger(weaker) at lower latitudes than higher latitudes in winter(summer). Frequency(%) of wind speed less than threshold value($18m\;s^{-1}$) for the operation date was investigated. The days showing the frequency greater than 60 % in all altitudes of surface ~ 50 hPa showed the range of 1 ~ 33 days at 7 stations. Operation date was the longest period at Gosan. The appropriate date of HALE UAV operation at Gosan and Osan is considered as the middle of July ~ middle of August and end of July ~ early August, respectively. These results can be used to determine the operation date of HALE UAV.

• Journal of Biosystems Engineering
• /
• v.28 no.2
• /
• pp.89-96
• /
• 2003

This study was aimed to identify how the main body vibration of power tiller will be transmitted to the trailer, and to find out the basic information for demage reducing method of agricultural products during transportation. The vertical vibration acceleration level was measured at 6 positions, i.e. engine, hitch, seal and three parts of trailer (front middle, and rear) for the not driving but at the engine speeds of 1,000rpm and driving at 0.35m/s. The results of this research could be summarized as follows; 1. For not driving, the accumulated acceleration level up to 120Hz was 50% of total accelerations at engine part and those were 28~41% at other parts. Those up to 40Hz were 20~30% at engine and hitch part and 2~8% at trailer part. And those up to 20Hz were 13~20% at engine and hitch part and 1~4% at trailer part 2. For the driving with 0.35m/s at paved road, the average vertical accelerations were in the range of 0.005~0.058m/s$^2$. The lowest value of 0.005m/s$^2$ was showed at engine part and the value of 0.031-0.058m/s$^2$ was showed at trailer part. 3. For the driving with 0.35m/s, the accumulated value of average vertical accelerations showed the lowest value at engine parts md showed 5 times value of engine part at trailer part especially highest value at middle part of trailer. 4. For the driving with 0.35m/s, the accumulated acceleration level up to 120Hz was 75% of total accelerations at engine part and those were 20~42% at other parts. Ant those up to 20Hz and 40Hz were 24~26% at engine part and 0.1~0.6% at trailer part.

• Wind and Structures
• /
• v.20 no.2
• /
• pp.213-236
• /
• 2015

For high-speed railways (HSR) in wind prone regions, wind barriers are often installed on bridges to ensure the running safety of trains. This paper analyzes the effect of wind barriers on the running safety of a high-speed train to cross winds when it passes on a bridge. Two simply-supported (S-S) PC bridges in China, one with 32 m box beams and the other with 16 m trough beams, are selected to perform the dynamic analyses. The bridges are modeled by 3-D finite elements and each vehicle in a train by a multi-rigid-body system connected with suspension springs and dashpots. The wind excitations on the train vehicles and the bridges are numerically simulated, using the static tri-component coefficients obtained from a wind tunnel test, taking into account the effects of wind barriers, train speed and the spatial correlation with wind forces on the deck. The whole histories of a train passing over the two bridges under strong cross winds are simulated and compared, considering variations of wind velocities, train speeds and without or with wind barriers. The threshold curves of wind velocity for train running safety on the two bridges are compared, from which the windbreak effect of the wind barrier are evaluated, based on which a beam structure with better performance is recommended.

• Journal of IKEEE
• /
• v.23 no.4
• /
• pp.1423-1429
• /
• 2019

Recently, a system that supports efficient interaction, a human machine interface (HMI), has become a hot topic. In this paper, we propose a new real time low-cost hand gesture control system as one of vehicle interaction methods. In order to reduce computation time, depth information was acquired using a time-of-flight (TOF) camera because it requires a large amount of computation when detecting hand regions using an RGB camera. In addition, fourier descriptor were used to reduce the learning model. Since the Fourier descriptor uses only a small number of points in the whole image, it is possible to miniaturize the learning model. In order to evaluate the performance of the proposed technique, we compared the speeds of desktop and raspberry pi2. Experimental results show that performance difference between small embedded and desktop is not significant. In the gesture recognition experiment, the recognition rate of 95.16% is confirmed.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.12 no.4
• /
• pp.87-94
• /
• 2013

This study estimated the changes in delays and speeds of vehicles in exclusive bus lane and road when the High Occupancy Vehicles(HOV) use the median bus lane. Synchro simulation tool was used to optimize the traffic signal time on the network and VISSIM was applied to simulate various scenarios. Here, drivers behavior parameters in VISSIM was optimized using Simultaneous Perturbation Stochastic Approximation(SPSA) algorithm in order to represent real traffic condition. Based on the simulation results, the delay in Doan daero was decreased when the volume of HOV in current condition runs on the median bus lane, whereas delay in Doan dongro was increased in all scenarios. The changes in bus speed was not sharply decreased for both study sites, even though the number of HOV increased to 10%. Thus, it could be allowed that the HOV use the median bus lane in Doan dongro and Doan daero. Future research tasks include studying about changes in delay when the HOV use the curb bus lane.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.3
• /
• pp.180-188
• /
• 2014

Hyundai Motor Group(HMG) carried out experimental investigation of sunroof buffeting phenomena on a simplified car model called Hyundai simplified model(HSM). HMG invited participation from commercial CFD vendors to perform numerical investigation of sunroof buffeting for HSM model with a goal to determine whether CFD can predict sunroof buffeting behavior to sufficient accuracy. ANSYS Korea participated in this investigation and performed numerical simulations of sunroof buffeting for HSM using ANSYS fluent, the general purpose CFD code. First, a flow field validation is performed using closed sunroof HSM model for 60 km/h wind speed. The velocity profiles at three locations on the top surface of HSM model are predicted and compared with experimental measurement. Then, numerical simulations for buffeting are performed over range of wind speeds, using advanced scale resolving turbulence model in the form of detached eddy simulation (DES). Buffeting frequency and buffeting level are predicted in simulation and compared with experimental measurement. With reference to comparison between experimental measurements with CFD predictions of buffeting frequency and level, conclusion are drawn about predictive capabilities of CFD for real vehicle development.

• Journal of Korean Society of Transportation
• /
• v.20 no.5
• /
• pp.163-174
• /
• 2002

Speeding has been reported as one of the major causes for fatal traffic accidents in Korea. The resolution against this dangerous speeding comes to make the automated speed enforcement system an enforcement tool. The speed detection device, which measures speeds of each incoming vehicles using double loop sensors, requires high accuracy. The object of this study is to develop an accurate speed measurement algorithm using double loop detectors. Some important findings are summarized as follows: 1) It was found that speed measurement errors are caused by scanning rate, distance of two loops, irregular vehicle trajectories, multiple vehicles in detection zone. 2) A proposed algorithm using two signal set proved to reduce variance as well as mean of speed measurement. 3) A proposed filtering algorithm was effective to filter irregular driving vehicles and multiple vehicles in detection zone. A comprehensive field test of developed algorithm resulted in significant improvement of speed measurement accuracy.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.552-556
• /
• 2002

The microstructure and electrical characteristics of A~C's ZnO varistors fabricated according to variable sintering condition, which sintering temperature is $1130^{\circ}C$ and speeds of pusher are A: 2mm/min, B: 4mm/min, C: 6mm/min, respectively, were investigated. In the microstructure, A~C's ZnO varist-ors fabricated variable sintering condition was consisted of ZnO grain(ZnO), spinel phase$(Zn_{2.33}Sb_{0.67}O_4)$ Bi-rich $phase(Bi_{2}O_{3})$, wholly. Varistor voltage of A~C's ZnO varistors sintered at $1130^{\circ}C$ increased in order A < B < C's ZnO varistors. C's ZnO varistor exhibited good characteristics that nonlinear exponent is 31.70. Leakage current of A~C's ZnO varistors exhibited below 2mA at rated voltage. Lightning impulse residual voltage of A's ZnO varistor suited standard characteristics, which is 3.85kV at 2.5kA, 4.4kV at 5kA and 5.16kV at 10kA. After multi lightning impulse residual voltage test of A's ZnO varistor exhibited good discharge characteristics which ZnO varistor reveals no evidence of puncture, flashover, cracking in visual examination. After high current impulse test of A's ZnO varistor exhibited good discharge characteristics, which variation rate of residual voltage is 0.4% before and after test, and revealed no evidence.

• Journal of the Korean Society for Railway
• /
• v.17 no.2
• /
• pp.133-139
• /
• 2014

Due to the absence of design guidelines for elevated light-rail structures in Korea, most elevated light-rail structures have been designed and constructed based on the design codes of conventional railway bridges and on the codes recommended by foreign vehicle manufacturers. This is the main reason why most elevated light-rail structures are massive or over-designed or poorly constructed economically. In this paper, the authors carried out field tests to analyze the braking forces caused by braking a train running at speeds of 50km/h, 60km/h, and 70km/h, acting on the elevated structures of rubber-wheeled Light Rail Transit (LRT) trains. The authors also briefly describe the analyzed results of the braking force acting on the substructures of elevated light-rail structures. The test-results presented here in this paper can be referenced when establishing design guidelines or standards for elevated structures of LRT systems.

• Journal of the Ergonomics Society of Korea
• /
• v.25 no.4
• /
• pp.129-135
• /
• 2006

he purpose of this study is to measure bio-signal to investigate the driver's physiological response change under real situation using train simulator. The train simulator used in this study is KTX model and according to changes of driving situation, The bio-signal controlled by autonomic nervous system, such as GSR(Galvanic Skin Response), SpO2(Saturation percent O2), HR(Heart Rate), ECG(Electrocardiograph), EEG(Electroencephagram) and movement and response of eye were measured. Statistically significant difference in bio-signal data and eye movement activity pattern were investigated under several different driving speeds using analysis of variance (p<0.05). The GSR and HR value measured in average and mission speed operation is higher than in high-speed operation. β wave of EEG in average speed operation become more activated than in high speed operation. In accordance with a characteristic of rail vehicle, movement and response of eye in high-speed operation requiring relatively simple maneuver become less activated than in either average or mission speed operations. Conclusively, due to more careful driving controls in average and mission speed operation are required than in high-speed operation, level of mental and physical stresses of train driver was increased and observed through changes of bio-signal and eye movement measured in this study.