• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.5
• /
• pp.358-364
• /
• 2009

This paper is to investigate the influence of driving patterns of slow and high speed vehicles on the performance of continuously regenerating diesel particulate filter(DPF) system matched with operating conditions in field application. The DPF performance test for field application was carried out for two identical DPFs installed to slow and high speed vehicles. A slow speed vehicle was selected among local buses which have driving patterns to repeat running and stop frequently, while a high speed vehicle was prepared to have long route of high speed over 60km/h like inter-city buses. In this test, the regeneration performance on the DPF of slow speed vehicle deteriorated because of high soot load index(SLI) in spite of same balance point temperature(BPT) distribution for high speed vehicle. The DPF of slow speed vehicle melted in the end because the rapid increase of back pressure caused high temperature over $1200^{\circ}C$ in the ceramic wall of DPF. The PM components like ash collected to the filter in the DPF were analyzed in order to investigate the cause of the defect and provide an operation performance of DPF system. In the result of the analysis, high levels of lubrication oil ash(Ca, Mg, P, Zn) were detected.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.35 no.1
• /
• pp.140-147
• /
• 2012

Vehicle routing problem is one of the traveling salesman problems with various conditions such as vehicle capacity limits, delivery time windows, as well as time dependent speeds in metropolitan area. In this research hourly vehicle moving speeds information in a typical metropolitan area are analyzed to use the results in the design procedure of VRP heuristic. Quality initial vehicle routing solutions can be obtained with adaption of the analysed results of the time periods with no vehicle speed changes. This strategy makes complicated time dependent vehicle speed simple to solve. Time dependent vehicle speeds are too important to ignore to obtain optimum vehicle routing search for real life logistics systems.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.1
• /
• pp.63-71
• /
• 2000

A shift control algorithm of a newly developed two-speed gear shift system is proposed for electric vehicle applications. The algorithm is formulated according to the motor torque map and optimized to obtain the adequate propulsion characteristics for vehicle. Two speed gear system with shift control algorithm has proved greater efficiencies in terms of energy economy with its simplified hardware and software structures. The gear shifting is designed to be carried out by an actuator and the control signal from a vehicle control unit equipped with $\mu$-processor. The results of performances and efficiency of the algorithm by simulation and vehicle test are described.

• Journal of Biosystems Engineering
• /
• v.21 no.4
• /
• pp.422-428
• /
• 1996

This study was conducted to developed to develop a simple battery-powered autonomous vehicle for greenhouse works. A steering method using speed difference of two independent driving motors was adopted. DC motor driving circuit, speed control circuit and controller using one-chip microcomputer were constructed. The inputs of controller are rolling of the vehicle and current speed of driving motors. Using these signals, automatic guidance system along furrow was developed. A computer simulation program by the kenematic analysis was developed to find out optimal control algorithm. The results of this study are as follows. 1. Automatic guidance system along the furrow that adopted two independent driving motors and rolling of vehicle was developed. 2. The results of simulation showed that PID control was adequate to automatic guidance system along furrow. 3. Two commercial 12V battery serially connected were able to drive the vehicle on the soil ground for five hours in continuous operation and for four hours in intermittent operation without recharging the battery. 4. The speed range was 0-0.7m/s and the rolling of vehicle could be controlled within $pm5^{\circ}$ range. 5. From a series of tests, developed vehicle was found to be a useful tool for greenhouse works.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.6
• /
• pp.1059-1068
• /
• 2016

The current operation method for the AVC (Automatic Vehicle Classification) equipment does not generate vehicle speed, traffic volume and vehicle type information when part of the sensors has failed. Inefficiency of current methods would not use the collected data from the normal sensor. In this study was conducted research on the calculating method at the traffic volume and vehicle speed in the sensor failure AVC equipment. The failure situation of the sensor was classified into 4 types. Calculating the traffic volume and vehicle speed information for each type, and accuracy of these informations were analyzed. Analysis results, traffic volume was possible to calculate a highly accurate value (accuracy: 100%, 98%, 97%). In the case of speed, the accuracy of the calculated speed value reaches a level that can be accepted sufficiently (RMSE value is less than 16.8). So, using the methodology proposed in this study are expected to be able to increase the operational efficiency of the AVC equipment.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1998.06a
• /
• pp.591-595
• /
• 1998

This paper proposes a new concept of optimal shortest path algorithm which reduce average vehicle wating time and improve average vehicle speed, Electro sensitive traffic system can extend the traffic cycle when three are many vehicles on the road or it can reduce the traffic cycle when there are small vehicles on the road. But electro sensitive traffic light system doesn't control that kind of function when the average vehicle speed is 10km -20km. Therefore, in this paper to reduce vehicle waiting time we developed design of traffic cycle software tool that can arrive destinination as soon as possible using optimal shortest pass algorithm. Computer simulation result proved 10%-32% reducing average vehicle wating time and average vehicle speed which can select shortest route using built in G.P.S. vehicle is better than not being able to select shortest route function.

• Wind and Structures
• /
• v.15 no.3
• /
• pp.263-283
• /
• 2012

This paper presents a framework of nonlinear dynamic analysis of a low-speed moving maglev (magnetically levitated) vehicle subjected to cross winds and controlled using a clipped-LQR actuator with time delay compensation. A four degrees-of-freedom (4-DOFs) maglev-vehicle equipped with an onboard PID (Proportional-Integral-Derivative) controller traveling over guideway girders was developed to regulate the electric current and control voltage. With this maglev-vehicle/guideway model, dynamic interaction analysis of a low-speed maglev vehicle with guideway girders was conducted using an iterative approach. Considering the time-delay issue of unsynchronized tuning forces in control process, a clipped-LQR actuator with time-delay compensation is developed to improve control effectiveness of lateral vibration of the running maglev vehicle in cross winds. Numerical simulations demonstrate that although the lateral response of the maglev vehicle moving in cross winds would be amplified significantly, the present clipped-LQR controller exhibits its control performance in suppressing the lateral vibration of the vehicle.

• International Journal of Highway Engineering
• /
• v.18 no.2
• /
• pp.103-110
• /
• 2016

PURPOSES: In this paper, the effectiveness of speed-maintained standardization in road geometry on environmental impact at a downward slope location, based on greenhouse gas (GHG) emission indicators, was studied. Specifically, the aim of this study was to ascertain whether speed-maintained standardization resulted in decreased $CO_2$ emissions as well as noise pollution, due to reduced vehicle speeds. METHODS : In this study, speed-maintained standardization in road geometry was proposed as a means to reduce vehicle speeds, with a view to reducing $CO_2$ emissions and noise pollution. This technique was applied at a downward slope location. The vehicle speeds, $CO_2$ emissions, and noise levels before and after application of speed-maintained standardization were compared. RESULTS: It was found that speed-maintained standardization was effective as a means to reduce speed, as well as $CO_2$ emissions and noise pollution. By applying speed-maintained standardization, it was confirmed that vehicle speeds were reduced consistently. As a result, $CO_2$ emissions and noise levels were decreased by 9% and 11%, respectively. CONCLUSIONS : This study confirmed that speed-maintained standardization in road geometry is effective in reducing vehicle speeds, $CO_2$ emissions, and noise levels. Moreover, there is further scope for the application of this method in the design of roads in urban and rural areas, as well as in the design of highways.

• Wind and Structures
• /
• v.29 no.5
• /
• pp.299-312
• /
• 2019

Due to the rugged terrain, metro lines in mountain city across numerous wide rivers and deep valleys, resulting in instability of high-pier bridge and insecurity of metro train under crosswind. Compared with the conditions of no-wind, crosswind triggers severer vibration of the dynamic system; compared with the short-pier viaduct, the high-pier viaduct has worse stability under crosswind. For these reasons, the running safety of the metro vehicle traveling on a high-pier viaduct under crosswind is analyzed to ensure the safe operation in metro lines in mountain cities. In this paper, a dynamic model of the metro vehicle-track-bridge system under crosswind is established, in which crosswind loads model considering the condition of wind zone are built. After that, the evaluation indices and the calculation parameters have been selected, moreover, the basic characteristics of the dynamic system with high-pier under crosswind are analyzed. On this basis, the response varies with vehicle speed and wind speed are calculated, then the corresponding safety zone is determined. The results indicate that, crosswind triggers drastic vibration to the metro vehicle and high-pier viaduct, which in turn causes running instability of the vehicle. The corresponding safety zone for metro vehicle traveling on the high-pier is proposed, and the metro traffic on the high-pier bridge under crosswind should not exceed the corresponding limited vehicle speed to ensure the running safety.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.234-240
• /
• 2002

This paper treats the problem of estimating the longitudinal velocity of a braking vehicle using measurements from an accelerometer and wheel speed data from standard anti-lock braking wheel speed sensors. We develop and experimentally test three velocity estimation algorithms of increasing complexity. The algorithm that works the best gives peak errors of less than 3 percent even when the accelerometer signal is significantly biased.