• Journal of Electrical Engineering and Technology
• /
• v.6 no.1
• /
• pp.48-58
• /
• 2011

In this paper, an attempt has been made to design the current and speed proportional and integral (PI) regulators of self-commutating current source inverter-fed induction motor drive having capacitors at the machine end and to investigate the transient performance of the same for step changes in reference speed. The mathematical model of the complete drive system is developed in closed loop, and the characteristic equations of the systems are derived using perturbation about steady-state operating point in order to develop the characteristic equations. The D-partition technique is used for finding the stable region in the parametric plane. Frequency scanning technique is used to confirm the stability region. Final selection of the regulator parameters is done by comparing the transient response of the current and speed loops for step variations in reference. The performance of the drive is observed analytically through MATLAB simulation.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.3
• /
• pp.320-327
• /
• 2002

An experimental study of heat transfer from hot flat surface to water sprays was conducted in high temperature region. Heat transfer measurements for hot flat surface were made by 4 sheathed C-A thermocouples. Droplets volume flux were also measured-independently at a position in spray field. The test conditions included variations in droplets volume flux, subcooling of cooling water of $1.565\times10^{-3} to 14.089\times10^{-3}m^3/m^2s and 80 to $20^{\circ}C$ respectively. The effects of inclination angle on heat transfer were investigated and changes in inclination angle of hot flat surface affected heat transfer coefficients of high temperature region.

• Proceedings of the KIEE Conference
• /
• 1988.11a
• /
• pp.414-417
• /
• 1988

This paper presents a study on the operation of a digitally controlled DC servo motor drive at low speed region. Two schemes aiming to improve the transient behavior of the speed control system are considered. The first scheme is the current positive feedback scheme to reduce the sensitivity of the system with respect to the load torque variations. The second one is the speed observer based on a motor model. Finally, the two schemes are studied by simulation and then verified experimetally using a prototype DC motor drive.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.6
• /
• pp.738-747
• /
• 1999

Vector controlled induction motor have been widely used in high performance applications. How-ever the performance is sensitive to the variations of motor parameters especially the rotor time constant which varies with the temperature and the saturation of the magnetizing inductance. In this paper the authors propose new identifying method for time-varying parameters of an induction motor which is based on adaptive vector control with serial block algorithm. Vector con-trol system realized on synchronous frame and parameter identification system realized on sta-tionary frame are not easily affected by the vector control frame. Parameter mismatch in the control system results in heavy transient variation in speed and torque response. In order to compensate degradation of the responses at the middle and low speed region adaptive identifier is introduced. To verify the feasibility of this technique compute simu-lations carried out.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.8 no.3
• /
• pp.210-216
• /
• 1984

An investigation of the effects of the size of mixing region determined by changing the position of fuel injection has been carried out. Measurements were made: the distribution of temperature and concentration profiles of the stable gas species, nitrogen oxide and total hydrocarbon in the flames. The results of this investigation show that variations of the size of mixing region produce major changes to the three type flow fields which significantly influence pollutant (NO, CO and THC) formation and energy release.

• Journal of Mechanical Science and Technology
• /
• v.20 no.10
• /
• pp.1716-1721
• /
• 2006

The Lubrication Mode of line contacts between the vane and the camring in an oil hydraulic vane pump has been investigated. First, the variations of the radial force of a vane were calculated from previous measurements of dynamic internal pressure in four chambers surrounding a vane. Next, the lubrication modes were distinguished with Hooke's chart, which is an improvement over Johnson's chart. Finally, the influence of the boundary conditions in the lubrication region on the fluid film lubrication was examined by calculating the film pressure distributions. The results showed that the lubrication mode of the vane tip exists in the rigid-variable-viscosity region, and that discharge pressure higher than 7 MPa greatly affects the oil film pressure in the small and the large arc section because of the Piezo-viscous effect.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.2
• /
• pp.302-312
• /
• 1992

Three dimensional velocity measurements of a 35.deg. inclined jet issuing into turbulent boundary layer on both concave and convex surfaces have been conducted. To investigate solely the effect of each curvature on the flow field, streamwise pressure variations are minimized by adjusting the shape of the opposite wall in the curved region. From the measured velocity components, streamwise mean vorticities are calculated to determine jet-crossflow interface. The results on convex surface show that the injected jet is separated from the wall and the bound vortex maintains its structure far downstream. On concave surface, the secondary flow in the jet cross-sections are enhanced and in some downstream region from the jet exit, the flow on the concave surface has been developed to Taylor-Gortler vortices

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.12
• /
• pp.3715-3727
• /
• 1996

Compression behavior of semi-solid aluminum alloys with controlled solid fractions was investigated in the present study. The stress and strain relationships were obtained from the compression test. Variations of the solid fraction distribution and the material behaviour were investigated for various friction coeffieiants and die speedsd. For a finite element analysis, the semi-solid material was described by a compressible regid viscoplastic model for the solid region and darcy's law for the liquid region. The computed results were compared with experimental data for the validity of the yield criteria.

• Industrial Engineering and Management Systems
• /
• v.16 no.1
• /
• pp.92-102
• /
• 2017

In this paper, we consider a typical health care system via the help of Wireless Sensor Network (WSN) for wireless patient tracking. The wireless patient tracking module of this system performs localization out of samples of Received Signal Strength (RSS) variations and tracking through a Particle Filter (PF) for WSN assisted by multiple transmit-power information. We propose a modified PF, Kullback-Leibler Distance (KLD)-resampling PF, to ameliorate the effect of RSS variations by generating a sample set near the high-likelihood region for improving the wireless patient tracking. The key idea of this method is to approximate a discrete distribution with an upper bound error on the KLD for reducing both location error and the number of particles used. To determine this bound error, an optimal algorithm is proposed based on the maximum gap error between the proposal and Sampling Important Resampling (SIR) algorithms. By setting up these values, a number of simulations using the health care system's data sets which contains the real RSSI measurements to evaluate the location error in term of various power levels and density nodes for all methods. Finally, we point out the effect of different power levels vs. different density nodes for the wireless patient tracking.

• Smart Structures and Systems
• /
• v.20 no.6
• /
• pp.657-668
• /
• 2017

In this research, an active vibration suppression of a smart beam having piezoelectric sensor and actuators is investigated by designing separate controllers comprising a linear quadratic regulator and a neural network. Firstly, design of a smart beam which consists of a cantilever aluminum beam with surface bonded piezoelectric patches and a designed mechanism having a micro servomotor with a mass attached arm for obtaining variations in the frequency response function are presented. Secondly, the frequency response functions of the smart beam are investigated experimentally by using different piezoelectric patch combinations and the analytical models of the smart beam around its first resonance frequency region for various servomotor arm angle configurations are obtained. Then, a linear quadratic regulator controller is designed and used to simulate the suppression of free and forced vibrations which are performed both in time and frequency domain. In parallel to simulations, experiments are conducted to observe the closed loop behavior of the smart beam and the results are compared as well. Finally, active vibration suppression of the smart beam is investigated by using a linear controller with a neural network based adaptive element which is designed for the purpose of overcoming the undesired consequences due to variations in the real system.