• Journal of the Korean Wood Science and Technology
• /
• v.26 no.4
• /
• pp.1-5
• /
• 1998

In this study, it was examined the method to estimate equilibrium moisture content(EMC) at high vapor pressures and high temperatures above $100^{\circ}C$. The material used for the experiment was Sugi(Cryptomeria japonica). EMC was investigated at temperatures ranging from $100^{\circ}C$ to $160^{\circ}C$ and under saturated vapor pressures above 1 atm. The correlation between temperatures and vapor pressures have a good agreement with those observed by thermocouple and pressure gauge in the air state of autoclave, respectively. A sensitivity of quartz spring was 65mm/g. Moisture content(MC)s calculated from the quartz spring elongation by vapor sorption showed a good agreement with MCs by oven-dried method. Using this system, it was found that EMC at high vapor pressures and high temperatures above $100^{\circ}C$ were higher than EMC of wood in 1 atm pressure conditions. With this system, therefore, it was concluded that the EMCs of wood and wood-based materials at high temperatures were able to be evaluated.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.4
• /
• pp.187-198
• /
• 2003

Zinc selenide (ZnSe) single crystals hold promise for many electro-optics, acousto-optic and green laser generation applications. This material is prepared in closed ampoules by the physical vapor transport (PVT) growth method based on the dissociative sublimation. We investigate the effects of diffusive-convection on the crystal growth rate of ZnSe with a low vapor pressure system in a horizontal configuration. Our results show that for the ratios of partial pressures, s=0.2 and 2.9, the growth rate increases with the Peclet number and the temperature differences between the source and crystal. As the ratio of partial pressures approaches the stoichiometric value of 2, the rate increases. The mass fluk based on one dimensional (1D model) flow for low vapor pressure system fall within the range of the predictions (2D model) obtained by solving the coupled set of conservation equations, which indicates the flow fields would be advective-diffusive. Therefore, the rate and the flow fields are independent of gravity acceleration levels.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.31 no.3
• /
• pp.127-136
• /
• 2021

This paper is dedicated to numerical simulation for diffusion-advective convection in a square cavity during physical vapor transport of Hg₂Br₂. Flow characteristics of the temperature difference between the source and crystal regions, 50℃ (300℃ → 250℃), partial pressures of component argon of 20 Torr and 100 Torr are investigated and presented as velocity vectors and streamlines, isotherms and iso-mass concentrations contours. Moreover, alterations of average Nusselt and average Sherwood numbers with (a) the source and crystal regions, (b) the pressures of component argon of 20 Torr and 100 Torr are analyzed and addressed in details. Both average Nusselt and average Sherwood numbers are seen to decrease with the increasing values of the partial pressures of component argon. Also, it is found that for the two different partial pressures of component argon, average Nusselt numbers at the source region are greater than at the crystal region, and inversely, average Sherwood numbers at the crystal region are greater than the source region by a factor of 3.

• Korean Journal of Materials Research
• /
• v.20 no.3
• /
• pp.111-116
• /
• 2010

Chloride-based fluxes such as NaCl-KCl are used in the refining of Al melt. The vapor pressure of the chloride is one of the fundamental pieces of information required for such processes, and is generally high at elevated temperatures. In order to measure the vapor pressure for chlorides, the apparatus for the transpiration method was assembled in the present study. The vapor pressure of $ZnCl_2$ and $FeCl_2$, which is related with the process of aluminum refining and the recovery of useful elements from iron and steel industry by-products, was also measured. In the measurement of vapor pressure by the transpiration method, the powder of $ZnCl_2$ or $FeCl_2$ in a alumina boat was loaded in the uniform zone of the furnace with a stream of Ar. The weight loss of $ZnCl_2$ and $FeCl_2$ after holding was measured by changing the flow rate of Ar gas (10 sccm -230 sccm), and the partial pressures of $ZnCl_2$ and $FeCl_2$ were calculated. The partial pressures within a certain range were found to be independent of the flow rate of Ar at different temperatures. The vapor pressures were measured in the temperature range of 758-901K for $ZnCl_2$ and 963-983K for $FeCl_2$. The measured results agreed well with those in the literature.

• Journal of the Korea Safety Management & Science
• /
• v.2 no.4
• /
• pp.33-43
• /
• 2000

The consequence analysis for the unconfined vapor cloud explosion(UVCE) accident by the continuous release of butane vapor was performed and effects of process parameters on consequences were analyzed in standard conditions. For the case of continuous release(87.8 kg/s) of butane vapor at 8 m elevated height in the debutanizing process of tile naphtha cracking plant operating at 877 kPa ＆ 346.75 K, we found that combustion ranges of dispersed vapor estimated by HMP model were 11.2~120.2 m and overpressures estimated by TNT equivalency model at 200 m were about 37.35~55.1 kPa. Also, overpressures estimated by Model UVCE I based on advective travel time to $X_{LFL}$ were smaller than those estimated by Model UVCE IIbased on real travel time between $X_{UFL}$ and $X_{LFL}$. At the same time, damage intensities at 200 m and effect ranges by overpressure could be predicted. Furthermore, simulation results showed that effects of operating pressures on consequences were larger than those of operating temperatures and results of accidents were increased with increasing operating pressures. At this time, sensitivities of overpressures for UVCE accident by the continuous release were about 5 kPa/atm.

• Korean Journal of Environmental Agriculture
• /
• v.6 no.2
• /
• pp.84-93
• /
• 1987

The water solubilities and vapor pressures of chlorothalonil and Command were measured following the guidelines of the U.S. EPA and OECD. Water solubility of the two compounds is consistent with respective values in the literature. However, the vapor pressures of Chlorothalonil and Command were 5,000 times$(2{\times}10^{-7}\;torr\;at\;25^{\circ}C)$ and 100 times$(<1{\times}10^{-6}\;torr\;at\;45^{\circ}C)$ lower than the literature values, respectively. Courteous use of the vapor pressure values in the handbooks is suggested. With this study, experimental difficulties involved were recognized. Based on the low vapor pressure of Command, the cause of the accidental bleach of non-target plants in the United States might not be attributed to the volatilization of Command, but to the drift during the application of the herbicide. These approaches will be utilized to predict the environmental fate of new chemicals under development, to screen the potential environmental pollutants among chemicals already in use, and to assess measures to minimize the hazards.

• Journal of Institute of Convergence Technology
• /
• v.3 no.2
• /
• pp.7-10
• /
• 2013

Metal oxides are known as stable materials during a thermal treatment. However, some oxides are readily evaporated at high temperatures. A voloxidation process is a head-end process for a pyroprocessing dealing with spent nuclear fuels (SF). In SFs, fission productions are in the form of oxides and some of them would be evaporated during the voloxidation process. Therefore, it is of importance to analyse the vapor pressures of metal oxides so that the material flows throughout the pyroprocessing could be estimated. In this work, vapor pressures of relevant metal oxides were calculated and presented to draw a baseline on the material flow of the pyroprocessing.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.12 no.3
• /
• pp.179-189
• /
• 2014

Pyroprocessing has been developed for the purpose of resolving the current spent nuclear fuel management issue and enhancing the recycle of valuable resources. An electrolytic reduction of the pyroprocessing is a process to reduce oxides into metals using LiCl as an electrolyte and requires a post-treatment process due to the inclusion of residual salt in porous metal products. A vacuum distillation has been adopted for various molten salt systems and could be applied to the post-treatment process of the electrolytic reduction. The residual salt in the metal products includes LiCl, alkali chlorides, and alkaline earth chlorides. In this paper, vapor pressures of chlorides have been estimated and the composition changes on the residual liquid during the vacuum distillation process have been calculated. A model combining a material balance and vapor-liquid equilibrium relations has been proposed under a constant vapor discharging flow rate and liquid composition changes have been calculated using the vapor pressures with respect to a dimensionless time. The behaviors have been compared with temperature and molten salt composition changes to simulate the process condition variation. The distillation of the residual salt has been dominated by LiCl which is the main component of the salt and CsCl of which vapor pressure is higher than that of LiCl would be readily removed. RbCl exhibits similar vapor pressure with LiCl and maintains its composition. However, $SrCl_2$ and $BaCl_2$ of which vapor pressures are much lower than that of LiCl are concentrated with time and expected to be possibly precipitated during the distillation when the initial compositions are increased.

• Fire Science and Engineering
• /
• v.12 no.2
• /
• pp.3-15
• /
• 1998

The consequence analysis for jet and flash fire accidents by the continuous release of butane vapor was performed and effects of process variables on consequences were analyzed in standard conditions. For the continuous release (87.8 kg/s) of butane vapor at 8m elevated height in the debutanizing process of the naphtha cracking plant operating at 877 kPa, 346.75 K, we found that for the jet fire accident, shape and size of the flame could be predicted and thermal radiation estimated by API model at 200m distance from release point was 1.5kW/$m^2$, and that for the flash fire accident, effect range was 11.2~120.2m. Also, simulation results showed that effects of operating pressures on consequences were larger than those of operating temperatures and results of accidents were increased with increasing operating pressures. At this time, effects of operating pressures on XUFL were smaller(about 1/10) than those on XLFL for the flash fire accident.

• Current Photovoltaic Research
• /
• v.4 no.3
• /
• pp.87-92
• /
• 2016

The effects of selenization pressure on the structural, optical and electrical properties of the CIGS thin films prepared by RF magnetron sputtering using a single quaternary target were investigated. At selenization pressures lower than atmospheric pressure, CIGS thin films formed non-stoichiometric compounds due to deficiencies of Se vapor. In contrast, when selenization process was conducted at above atmospheric pressure, the residence time of Se vapor inside the tube increased so that the Se element could be incorporated within vacant sites of the CIGS structure, resulting in the formation of stoichiometric CIGS thin films. High quality CIGS thin films could be obtained when the selenization process was performed at pressures greater than atmospheric and $550^{\circ}C$.