Transactions of the Korean Society of Mechanical Engineers
/
v.11
no.6
/
pp.913-922
/
1987
In this paper the solidification phenomena at the molten pool has been modeled and simulated in terms with the one dimensional unsteady-state heat transfer of the solid and molten phase and the pressure distribution in the solid phase for the twin-roller continuous casting of Sn-15% Pb. The further purpose of this study was to effectively analyze the thermal and mechanical deformation of roll applying the results of the heat transfer and the pressure distribution to the boundary conditions. The strip thickness of rapidly solidified metallic strip decreases with increasing angular velocity of the roller and with increasing initial roll gap. For this reason the roll spacing and angular velocity of the rolls are considered to be main variables. The recommended optimal casting regimes for continuous strip dimensions is near 0.8mm-1.0mm in thickness at the given angular velocity .omega.=2.0 rad/sec. Results of the experiment using Sn-15% Pb are compared with model predictions. The calculated roll deformation has been in good agreement with the observed value of roll deformatiion. All the deformation. All the deformation of the roller is within the elastic range, the plastic yielding are not occured. However, these elastic stresses are sufficient to take place of the shortened roller life by the thermal fatigue and a notch fatigue. The higher cooling rates were obtained by a twin-roller quenching technique. Also the quenched microstructure of the rapidly solidified shell was verified.
Electrical properties and microstructure were investigated on the effects of $MnO_2$ and the lead-free $(Na_{0.44}K_{0.52}Li_{0.04})(Nb_{0.83}Sb_{0.07}Ta_{0.1})O_3$ ceramics with the addition of $MnO_2$ were fabricated by a conventional mixed oxide method. A gradual change in the crystal and microstructure was observed with the increase of $MnO_2$ addition. For the NKN-LST-xmol%$MnO_2$ sintered at $1100^{\circ}C$, bulk density increased with the addition of $MnO_2$ and showed maximum value at addition 1.0mol% of $MnO_2$. Curie temperature of the NKN-LST ceramics slightly decreased with adding $MnO_2$. The dielectric constant, piezoelectric constant ($d_{33}$) and electromechanical coupling factor ($k_p$) increased below 0.25mol% of $MnO_2$ addition, which might be due to the increase in density. The high piezoelectric properties = 145 pC/N, electromechanical coupling factor = 0.421 and dielectric constant = 2883 were obtained for the NKN-LST-0.25mol%$MnO_2$ sintered at $1100^{\circ}C$ for 4h.
Journal of the Korean Academy of Clinical Electrophysiology
/
v.5
no.2
/
pp.85-93
/
2007
Summary of background data: It is researched until now and the researches against the effect of position cold treatment the effect which pain threshold, change of skin temperature, researches the effective stiffness, the coldness in the patient it applied and relax an inflammation do the researches against were insufficient. Purpose: This project was to see how much it gives effect by using the cold air therapy an inflammation relief of rheumatoid arthritis patient. Methods: The medical subjects were 10 people from standard to diagnosis category of American College of Rheumatology(ACR) who had rheumatoid arthritis and to inspect informations about inflammation relief, have inspected ESR(erythrocyte sedimentation rate) and WBC(white blood cells). The experiment method was to let the patient bend the joint and lay down flat and treat with cold air from 10 cm away from joint line repeating 5 minutes treatment 1 minute rest and 3 minutes treatment. ESR and WBC cold air therapy reported with 5 days gap and each patient has been applied for 3 times. Result: The 5th day and 10th days ESR and WBC value shows when using cold air therapy, there was a reduction on rejected group but didn't last long, but 15th day it showed only on WBC it had its attention. Conclusions: So the cold air therapy shows it has positive effects on inflammation relief of rheumatoid arthritis patient.
Journal of the Korean Professional Engineers Association
/
v.13
no.4
/
pp.31-47
/
1980
Since medium and small manufacturing enterprises have , played a very important role not only in national economy but also in political and social relationships all of the countries in the world have paid favorable policies and programmes for protecting and promoting this sector. In Korea main ingredients of promoting policy for this sector consist of (1) encouragement to modernize facilities and rationalize operation (2) special priority in bank loan (3) promotion of industrial cooperatives (4) prevention of infringement by large industries. However, substantial investigation for problems incurred in medium industries has revealed that unless medium industries improve and raise their technological and managerial skillfulness for themselves all other measures are useless to solve the problems. This realization has induced all of the countries to render extension services on both of technology and management to assist and support their own effort for rationalization. Also in Korea during past 20 years many technical and managerial research institutes have rendered free consultancy services to medium industries by the support of government subsidy. Among them the joint extension services project performed by the Medium Industry Bank and UNDP during 1967 and 1975 might he listed as model case because of its broad and integrated activities and participation of foreign experts. We think many precepts should be :learned from the study of this project. Korean economy is expected to develop rapidly throughout coming'80 in spite of many obstacles, tut there is an apprehension that gap in of every facet between medium and large enterprises might he deepened and enlarged. To prevent the actualization of so-called dual structure of national economy and to promote stabilized medium industries with high added value productivity which are shown in well developed countries, consultancy assistance ana extension services should be strengthened much more than ever. Fortunately in 1978 legislation of "Medium and small industry promotion act" has paved the way for the systematic achivement of consultancy and extension services which shall be integrated by the government overall program. Under new framework thoughtfull accomplishment should be undertaken considering precious precepts obtained from past experience and failure. Special attention should be given to the technical liaison officer scheme, exclusive participation of only professional institutes, strict qualification and training for consultants for the future succsseful implementation.
Health industry, a knowledge based high value-added industry, is being considered as a strategic area for the 21C and many advanced countries are making every endeavors for the promotion of health industry along with information technology, new materials, and mechatronics. Korean health industry, however, has been excluded from the governmental supports as well as bound by strict regulation so far, and there is a significant gap in technology compared with advanced countries. In 21C, technology is the main factor of national competitiveness and that is why the role of R&D institutes are so important in the high level of competition to cope with the technology protection policies of advanced countries. In this article, with Directory of Korean R&D Institutes published by Korea Industry Technology Association, I reviewed the trends of R&D institute of health industry. Main findings of the research can be summarized as follows. The portion of health industry R&D institute is 3.6% of total R&D institute but the amount of R&D investment is over than 5% This means health industry are knowledge based and R&D intensified industry, meanwhile the variations of same industry R&D institutes of health industry is huge in R&D investments and other activities. Regional distributions of health industry institutes show some kind of different patterns in each industry areas. Medical devices and Medical informatics's preference of metropolitan region are distinguished with other industry areas. Many of the institutes are located in same site of it's company rather than operating separate building for R&D specific uses. It is better for transforming ideas to products and close cooperation of research body with product lines, but it is a handicap for networking and communicating with other research institutions too. It takes 18.4yrs for bearing R&D institute on the average. For a long times 'copy products' or 'me too products' policies were easy way to maintain business entities. But recently, it is recognized that research activities are essential component of sustaining it's own business firms. This means technology itself is leading power of corporation itself in the high level of competition.
The Journal of the Korea institute of electronic communication sciences
/
v.14
no.6
/
pp.1241-1248
/
2019
In this paper, an auxiliary device was implemented to help blind people more safely from obstacles or risk factors while walking. The ultrasonic sensors detect obstacles in the front, so that the noise gap and the vibration intensity of the buzzer can be heard differently by distance and angle, and so the situation can be perceived by pedestrians. When the ambient light becomes darker than the light intensity set using the CdS resistance value of the light sensor, the LED automatically turns on, makes it easier for pedestrians to recognize the position of the auxiliary device through buzzer if the pedestrian misses the aid using the gyro sensor's slope. Moreover, the location and situation of the blind were transmitted to the caregiver to check safety and behavior using GPS and Bluetooth.
Journal of the Korean Institute of Electrical and Electronic Material Engineers
/
v.23
no.10
/
pp.771-775
/
2010
In this study, piezoelectric and dielectric properties of the $(Na_{0.5}K_{0.5})NbO_3-(1-x)(Bi_{0.5}Na_{0.5})TiO_3-xBaTiO_3$ [NKN-(1-x)BNT-xBT] ceramics were investigated. The lead-free NKN-(1-x)BNT-xBT ceramics were fabricated by a conventional mixed oxide method. The results indicate that the addition of $BaTiO_3$ significantly influences the sintering, microstructure, phase transition and electrical properties of NKN-BNT ceramics. A gradual change in the piezoelectric and dielectric properties was observed with the increase of BT contents. The dielectric constant, piezoelectric constant ($d_{33}$) and electromechanical coupling factor ($k_p$) increased at the morphotropic phase boundary (MPB). The $d_{33}$=184 pC/N, $k_p$=0.38, dielectric constant=1455 with dielectric loss value of less than 1% were obtained for the NKN-0.95BNT-0.05BT ceramics sintered at $1150^{\circ}C$ for 2h. These results demonstrate that the NKN-(1-x)BNT-xBT ceramics is an attractive candidate for lead-free piezoelectric materials.
Journal of the Korean Institute of Electrical and Electronic Material Engineers
/
v.27
no.6
/
pp.394-398
/
2014
We fabricated the electrolyte-dielectric-metal (EDM) sensor on the base of AAO (anodic aluminum oxide) template with variation of the anodizing temperature. When a surface is immersed or created in an aqueous solution, a discontinuity is formed at the interface where such physicochemical variables as electrical potential and electrolyte concentration change significantly from the aqueous phase to another phase. Because of the different chemical potentials between the two phases, charge separation often occurs at the interfacial region [1]. This interfacial region, togeter with the charged surface, is usually known as the electrical double layer (EDL) [2]. The structural and electrochemical properties of AAO sensor were investigated for applications in capacitive pH sensors. To change the thickness of the AAO template, the anodizing temperature was varied from $5^{\circ}C$ to $20^{\circ}C$, the thickness of the AAO template invreased from 300 nm to 477 nm. The pH sensitivity of sensors with the anodizing temperature of $20^{\circ}C$ showed the highest value of 56.4 mV/pH in the pH range of 3 to 11. The EDM sensor with the anodizing temperature of $20^{\circ}C$ exhibited the best long-term stability of 0.037 mV/h.
Raised or plain block is widely used for the pedestrian's safe passage. The insincere construction, insufficient maintenance and obstacle overlaid on the pavement cause pedestrian's accidents. This paper proposes a method to detect brick path by analyzing the shape pattern and texture feature of brick located in visible distance for a safe passage. A brick appears to a regular type because of its specific shape which repeats with its sized gap and its type varies according to the surrounding environment or use. This paper shows a method which extracts the shape pattern by analyzing single surface polygon and its frequency appearing in road area. The shape pattern is used to detect similar shape regions. Some regions are not detected because extraneous substances or chopped bricks distort the original shape. This problem can be solved by analyzing the texture feature vector. The analyzed vector of the previously detected regions yields the Gaussian distribution. This value in each undetected region is computed and checked whether it's satisfied with Gaussian distribution or not. The satisfied region is detected as the brick path. The experiment was performed with the various type's bricks to recognize so that the results showed as accurate as 95.9% in average.
Asia-Pacific Journal of Business Venturing and Entrepreneurship
/
v.9
no.6
/
pp.101-108
/
2014
The creation of new venture firm has been regarded as a key of creating more job opportunities and discovering new value engines for various industries. It is positively expected that venture capitals play an important role of supporting the process. Nevertheless, there is a scant of research efforts to analyze empirical data for understanding cross-correlations between investment of venture capital and new venture foundation. To fill the gap, this study investigated sets of time-series data from 1998 to 2014 in the context of South Korean economy. The results reveal that venture capitals have contributed significantly to the quantitative increase of venture firms. In addition, the findings show that the creation of new venture fails to yield a direct impact on resolving young unemployment problems in short term. The paper contributes to the research community on new venture foundation by providing insightful views.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.