• 제목/요약/키워드: upset pressure

검색결과 50건 처리시간 0.027초

회주철의 마찰용접 특성에 관한 연구 - 입열량 이론식을 중심으로 - (Friction Weldability of Grey Cast Iron - by the Concept of Friction Weld Heat Input Parameter -)

  • 정호신;방국수
    • Journal of Welding and Joining
    • /
    • 제32권3호
    • /
    • pp.95-101
    • /
    • 2014
  • Joining of grey cast iron by fusion welding has much difficulties for its extremely low ductility and low toughness because of the flake form of the graphite. And the brittle microstructure, i.e. ledeburite may be formed during fusion welding by its rapid cooling rates. By these kinds of welding problem, preheat and post heat treatment temperature must be increased to avoid weld crack or welding problems. In order to avoid these fusion welding problem, friction welding of cast iron was carried out for improving joint soundness, establishing friction welding variables. There is no factor for evaluating friction weldability in continuous drive type friction welding. In this point of view, this study proposed the parameters for calculating friction weld heat input. The results obtained are as follows ; 1. There was a close relationship between tensile strength and flash appearance of friction welded joint. 2. Tensile strength was decreased and flash was severely oxidized as increasing frictional heating time. 3. As increased forging pressure $P_2$, flash had a large crack and tensile strength was decreased. 4. As powdered graphite by rotational frictional force induced flat surface and hindered plastic flow of metal, tensile strength of welded joint was decreased. 5. Heat input for continuous drive type friction welding could be calculated by the factors of $P_1$, $P_2$ and upset distance(${\delta}$).

서보모터방식 마찰용접을 이용한 TiAl 합금과 SCM440의 접합에 미치는 용접조건의 영향 (Effects on the Joining Condition of TiAl Alloy and SCM440 by Servo Motor Type Friction Welding)

  • 박종문;김기영;김경균;오명훈
    • 열처리공학회지
    • /
    • 제29권2호
    • /
    • pp.66-74
    • /
    • 2016
  • In this study, characteristics of TiAl alloy and SCM440 (Cr-Mo steel) have been investigated with the various joining condition by servo motor type friction welder. The experimental factors of friction welder used in this study are spindle revolution, friction speed, and distance, upset speed and distance, respectively. Servo motor type friction welder could be controlled by the level of oil pressure, and it could be performed by position control dependence of electrical energy. Mechanical properties and morphology of welded interface were characterized by various joining condition. This aroused due to the bond strength dependence on friction heat and size of the heat affected zone. Therefore, it is necessary to have enough friction heat and decreased heat affected zone for good friction welding between dissimilar metals. An optimum bond was obtained between TiAl alloy and SCM440 by controlling friction speed and distance. At the spindle revolution 4,000 rpm, friction speed 120 mm/min, friction distance 15 mm, the bond strength was found to be 312 MPa.

마찰접합 된 A6063 합금의 미세조직과 기계적 특성 평가 (Evaluation of the Microstructures and Mechanical Properties on Friction Welded A6063 Alloy)

  • 김은혜;조형환;송국현
    • 한국재료학회지
    • /
    • 제27권5호
    • /
    • pp.276-280
    • /
    • 2017
  • This study was carried out to evaluate the developed microstructures and mechanical properties of friction welded A6063 alloy. For this work, specimens were prepared at a size of 12 mm ${\O}{\times}80mm$, and friction welding was carried out at a rotation speed of 2,000 RPM, friction pressure of $12kgf/cm^2$ and upset pressure of $25kgf/cm^2$. To perform an analysis of the grain boundary characteristic distributions, such as the grain size, orientation and misorientation angle distributions, the electron back-scattering diffraction method was used. In addition, in order to identify the dispersed intermetallic compounds of the base and welded materials, transmission electron microscopy was used. The experimental results found that the application of friction welding on A6063 led to significant grain refinement of the welded zone relative to that of the base material. Besides this, intermetallic compounds such as AlMnSi and $Al_2Cu$ were found to be dispersed with more refined size relative to that of the base material. This formation retains the mechanical properties of the welds, which results in the fracture aspect at the base material zone. Therefore, based on the developed microstructures and mechanical properties, the application of friction welding on A6063 could be used to obtain a sound weld zone.

초급간부 군 상담모델 개발 연구 (Study on primary officer military counseling model)

  • 서선우
    • 융합보안논문지
    • /
    • 제16권6_1호
    • /
    • pp.75-83
    • /
    • 2016
  • 병력관리는 군 사고예방은 물론 전투력 보존 및 발휘의 핵심이다. 그러나 예측하지 못한 시간과 장소에서 생각지도 못한 부대원이 사고를 유발하게 되면 경험 없는 초급간부들은 당황하며 어떻게 처리해야 할지 몰라 전전긍긍할 때가 많다. 뿐만 아니라 각종 사고를 예방하는 것도 군의 존립의 이유인 전쟁에서의 승리를 위한 전투준비태세 완비의 전제 조건이다. 이 막중한 임무의 최전선에 초급간부들이 있다. 그러나 전투준비를 위한 제반업무에 만전을 기하여야 할 시간도 부족한데 병력관리에 대한 상급부대의 지시와 요구되는 수준은 경험이 부족한 초급간부들에게 많은 스트레스를 주는 것이 사실이다. 그래서 초급간부를 위한 군 상담모델을 연구하게 되었다. 초급간부 군 상담모델을 적용하여 상담을 진행 하면 가장 신속하고도 효율적으로 상담대상에 대한 파악이 가능하다. 효율적인 상담은 깊이 있는 내담자의 이해가 선행되어야 한다. 누군가를 심층 있게 이해한다는 것은 많은 노력과 시간을 필요로 하는 행위이다. 그러나 초급간부들은 그러한 시간과 노력을 충분히 투자할 수 있는 여건이 미흡한 것이 사실이다. 그러므로 초급간부 군 상담모델을 적극 활용하여 선택과 집중을 통한 상담활동을 지속한다면 효과적인 상담 및 사고예방까지 가능할 것이다.

남자 고등학생 흡연자의 영양상태 판정 및 흡연관련 요인분석 -II. 흡연과 관련된 사회심리적 요인에 대한 연구- (Assessment of Nutritional Status and Factors Related to Smoking in Adolescent Males -II. Psychosocial Factors Influencing Smoking among Male High School Students-)

  • 김경원;김소림;김정희
    • 대한지역사회영양학회지
    • /
    • 제3권3호
    • /
    • pp.358-367
    • /
    • 1998
  • The study purpose was to investigate psychosocial factors related to smoking among adolescent boys. The Theory of Planned Behavior provide the basis for the study. Twenty-five attitudinal beliefs, 9 normative beliefs and 20control beliefs were identified through questionnaire development. The data were analyzed using t-test and χ2-test. Thirty-three percent of 300 students were smokers. Most of the beliefs examined were significantly different between smokers(n=92) and nonsmokers(n=92). With respect to attitudinal beliefs, smokers responded less negatively on the items of bad health effects of smoking such as sore throat, headache, chest pain, risk of cancer and bad blood circulation(p<0.001), and decreased physical strength(p<0.05). Smokers believed less negatively on the items that smoking leads to bothering others, bad breath, yellow teeth and making them spend money(p<0.001). In contrast, smokers felt more positively on smoking as a means of stress management, relaxing, helping digestion(P<0.001). Smokers felt less pressure for not smoking from significant others. Especially mother, siblings, friends, girl friends, seniors of school were important sources of influence regarding subject's smoking. Smokers felt less confident in controlling the urge to smoke in several situations including; when they were with friends or asked to smoke by friends; after the meal, or drinking; when they were bored or stressed, upset, and when they felt unstable(p<0.001). Smokers also scored lower on specific skills to quit or control the urge to smoke as well as overall perceived control, compared to nonsmokers(p<0.001). These results suggest that interventions for adolescents incorporate diverse strategies to increase the perceived control over smoking in specific situations as well as overall perceived control, to help them realize and modify attitudinal beliefs, and to elicit support from significant others for not smoking. (Korean J Community Nutrition 3(3) : 358∼367,1998)

  • PDF

기관배기 밸브용 강 ( SCr4-21-4N , SUH3-21-4N ) 의 마찰압접과 열처리에 관한 실험적 연구 (An Experimental Study on Friction Welding and Heat Treatment of Engine Exhaust Valve Steels ( SCr4-21-4 N , SUH3-21-4-N)

  • 오세규
    • 수산해양기술연구
    • /
    • 제14권2호
    • /
    • pp.79-87
    • /
    • 1978
  • 기관밸브용접 SCr4-21-4N 및 SUH3-21-4N을 연구선정된 최적마찰압접조건 하에서 마찰압접을 하고 이때 생기는 압접부의 잔류응력 및 경도의 peak 등 압접결함의 제거 및 압접성능개선을 위한 열처리에 관하여 실험연구한 결과 다음과 같은 결론을 얻었다. (1) 배기 valve용강 SCr4-21-4N 및 SUH3-21-4N의 마찰압접을 위한 최적조건으로서 회전수 3,000rpm, 마찰가열압 p 하(1)=8 kg/mm 상(2), upset 압 p 하(2)=20 kg/mm 상(2), 압접가열시간 t 하(1)=3초, upset 시간 2.5초를 선정한 것이 매우 타당함이 실험적으로 입증되었다. (2) 이종재질 SUH3-SUH31, SCr4-SUH31, SCr4-SUH3, SUH3-CRK22, SCr4-21-4N 및 SUH3-21-4N의 마찰압접에 관한 저자의 종래 연구와 본연구 결과는 압접부의 압접 특성이 서로 매우 일치하였다. (3) SCr4-21-4N 및 SUH3-21-4N의 마찰압접부의 잔류응력 및 전도의 peak를 제거하기 위한 최적열처리조건은 $600^{\circ}C$$\times$30min.$\times$room air cooling의 normalizing임이 확인되었다. (4) 이때 열처리 후에는, 열처리전의 인장강도의 약 20%가 감소했으나, 파단 위치는 열영향부로부터 모재 SCr4 및 SUH3 측으로 이동하였다. (5) 상기 최적조건 하에서 마찰압접되고 열처리된 압접부의 현미경 조직검사 결과, 압접부가 매우 좁고 압접결함이 없으며, 치밀하고 조밀한 조직의 우수한 압접이었음이 확인되었다. (6) 상기 최적조건은, 기관 valve 생산을 위한 타이종재질의 마찰압접조건으로도 응용될 수 있을 것이다.

  • PDF

마찰용접된 국산내열 강 (SUH3-SUS303 )의 시효열처리가 고온피로강도 및 파괴거동에 미치는 영향에 관한 연구 (The Effect of Aging Treatment on the High Temperature Fatigue Fracture Behavior of Friction Welded Domestic Heat Resisting Steels (SUH3-SUS 303))

  • 이규용;오세규
    • 수산해양기술연구
    • /
    • 제17권2호
    • /
    • pp.93-103
    • /
    • 1981
  • Si-Cr계 내열강 SUH3와 Cr-Ni계 stainless강 SUS 303 및 이들이 마찰용접재 SUH3-SUS303을 $1,060^{\circ}C$에서 용체화처리하고 다시 $700^{\circ}C$에서 10, 100시간 시효열처리한 각 시험편의 고온 피로강도에 대한 시효열처리의 효과를 알기 위하여 $700^{\circ}C$에서 고온 회전굽힘 피로시험을 하고 파약거동을 미시적으로 관찰하여 다음과 같은 결과를 얻었다. 1) SUH3재와 SUS303재의 최적마찰용접조건은 회전수 2420rpm, 마찰가압력 $8kg/mm^2$, 전 upset량 7mm(마찰가압시간 3sec, upset시간 2sec)이었다. 2) $700^{\circ}C$ 고온에서 장시간 이루어지는 고온피로시험에 있어, 용체화처리재의 S-N 곡선 경사부의 기울기가 가장 급하게 나타났다. 3) SUH3-SUS303 마찰용접재는 $1,060^{\circ}C$에서 1시간용체화 처리하고, $700^{\circ}C$에서 시효처리하는 경우 최적시효시간은 10시간이었다. 4) 10시간 시료재의 고온피로한도는 모재보다 SUH3은 75.4%, SUS303은 28.5% 높았으며, 용접재 SUH3-SUS303은 44.2% 정도 높았다. 100시간 시효재는 모재보다 SUH3은 64.91% SUS303은 30.4% 높았으며, SUH3-SUS303은 30.4% 높았으며, SUH3-SUS303은 36.6% 높았다. 5) 마찰용접재의 상온 및 고온의 피로파단은 모두 SUS303의 모재측에 발생하였으며, 용접면에서의 파단은 전혀 없었다. 6) SUS303재와 마찰용접재 SUH3-SUS303재의 크랙은 입내파양형이었으나 SUH3은 입계크랙의 전파로 파양한다.

  • PDF

이종강의 마찰압접시 압접시간 변화에 따른 강도거동-SM45C와 SUS304재의 경우 (The behavior of strength on friction welding of dissimilar steels by various heating time : in case of SM45C and SUS304 materials)

  • 박명과;박명과
    • 대한기계학회논문집
    • /
    • 제11권5호
    • /
    • pp.762-771
    • /
    • 1987
  • 본 연구에서는 국산 구조용 강인 SM45C와 SUS304재를 마찰가열압력과 업셋압 력을 서로 변화시키고 업셋시간을 2초로 고정하여 압접시간 10초를 기준으로 하여 변 화시키면서 마찰압접한 후 압접시간 변화에 따른 인장강도의 변화와 업셋량 변화에 따 른 인장강도 및 굽힘강도를 고찰하였다.또 최고 강도치를 나타내는 압접조건을 구 한 후 미소 경도치 및 이종재의 압접부에서 미소하게 변화하는 조직변화도 함께 고찰 하였다.

기계적 합금법으로 제조된 Ni기 산화물 분산강화 합금의 마찰압접에 관한 연구 (Friction Welding of Ni-Base ODS Alloy Prepared by Mechanical Alloying)

  • 강지훈;박성계;김지순;권영순
    • 한국분말야금학회:학술대회논문집
    • /
    • 한국분말야금학회 1994년도 추계학술대회강연 및 발표대회 강연및 발표논문 초록집
    • /
    • pp.15-15
    • /
    • 1994
  • M MA ODS 합금의 보다 폭넓용 실용확훌 위해 크게 요구되고 있는 적정 접합기술 개발의 한 방안£로, 마찰압접(Friction Welding) 방법의 가능성옳 조사하기 위하여 마찰압력과 시간, 마 찰 후 접촉압력(Upset Pressure) 풍을 다양하게 변화시켜 접합체톨 제조한 후, 접합체 강도에 대한 인장시험과 접합계연의 결합 및 미세구조에 대한 현미경 관찰, EDS에 의한 원소분석, 접 합이옴부의 경도분포와 파단면 분석 풍율 행하였다. 실험에 사용된 모재는 기계적 합금법으로 제조된 Inca사의 Ni기 MA 754 합금이었으며, 직경 l 10 mm, 길이 50 mm로 가공한 후, 아세통£로 초음파 세척하여 접합에 사용하였다. 접합온 브 레이크식 마찰압접기틀 사용하여 행하였으며, 회전시험편의 회전수는 2400 rpm이었A며, 다른 한쪽의 고정시험편과의 마찰압력 및 마찰시간온 각각 50 - 500 MPa과 1-5초로, 또한 업셋압 력도 50 - 600 MPa로 변화시켰다. 이때 업셋압력은 모든 시편에 대해 일정하게 6초동안 가하 였다. 얻어진 접합체는 각 압접조건 당 2개 이상의 접합시험편에 대해 상온 인장강도톨 측정하 였으며, 파단이 일어난 위치를 확인한 후 파면에 대한 분석율 주사전자현미경(SEM)과 에너지 분산형 분광분석기mDS)릎 사용하여 행하였다. 컵합이옴부의 첩합성올 확인하기 위하여, 접합 체를 접합변에 수직으로 절단, 연마한 후 광학현미경과 SEM, EDS 퉁으로 관찰, 분석하여 접 합부의 형상과 결합형성 여부, 접합계면의 미세조직 퉁옳 조사하였다. 또한 마찰압접에 따론 모재와 접합계연부의 경도분포훌 접합이옴부로부터 모재쪽으로 일정 간격율 두어 마이크로 비 커스 경도기로 측정, 조사하였다. 이상의 설험 결과, 다옴과 같온 결론옳 얻었다. ( (1) 접합체 강도가 모채 강도의 95% 이상이 되는 양호한 렵합체흩 얻기 위한 마찰압력 조건 온, 2400 rpm의 회전속도와 6초의 업셋압력 유지시간에서 마찰압력과 업셋압력, 그리고 마찰시 간이 각각 400 MPa 이상과 500 MPa 이상,2초입율 확인하였다. ( (2) 컵합이옴부의 관찰 결과, 모든 마찰압접 조건에서 컵합이옴부는, 기폰 모재의 texture 조직 을 유지하고 있는 모재부 영역(영역 ill)과 첩합계면부에 인접하여 업셋압력이 주어질 때 단조 효과에 의해 계연 외부로 metal flow가 일어나면서 형성된 영역 II, 매우 미세한 결정립으로 구성된 중앙부의 영역 1 로 이투어져 있옴융 확인하였다. ( (3) 최적접합조건이 충족되지 않온 경우, 접합부의 영역 I 에서 관찰된 void와 균열, 불균일한 접합계면 통의 접합결함에 Al과 Y. Ti 퉁£로 구성된 산화물률이 용집되어 있옴을 확인하였 다-( (4) 접합체의 파단 양상온 크게 접합부 파단과 모재부 파단, 이률의 혼합형 파단i로 나눌수 있었다. 모재부 파단의 경우, 파단면이 매끄럽고 파변상의 결정립도 매우 미세하였으며, 산확물 의 용집도 찾아보기 어려웠 나, 접합부 파단의 경우에는 파변의 굴곡이 비교척 심하고 연성 입계파괴의 형태를 보였£며, 결정립도 모채부 파단의 경우에 비해 조대하였다. 조대하였다.

  • PDF

노인성 치매 환자의 돌봄경험에 대한 문화기술지 (Ethnography of Caring Experience for the Senile Dementia)

  • 김귀분;이경희
    • 대한간호학회지
    • /
    • 제28권4호
    • /
    • pp.1047-1059
    • /
    • 1998
  • Senile Dementia is one of the dispositional mental disorder which has been known to the world since Hippocratic age. It has become a wide-spread social problem all over the world because of chronic disease processes and the demands of dependent care for several years as well as improbability of treatment of it at the causal level. Essentially, life styles of the older generation differ from those of the younger generation. While the fomer is used to the patriarchal system and the spirit of filial piet and respect, the latter is pragmatized and individualized under the effects of the Western material civilization. These differences between the two generations cause conflict between family members. In particular, the pain and conflict of care-givers who take care of a totally dependent dementia patient not only is inciting to the collapse of the family union, but is expanding into a serious social problem. According to this practical difficulty, this study has tried to compare dementia care-givers' experiences inter-culturally and to help set up more proper nursing interventions, describing and explaining them through ethnographies by participant observation and in-depth interviews that enable seeing them in a more close, honest and certain way. It also tries to provide a theoetical model of nusing care for dementia patients which is proper to Korean culture. This study is composed of 12 participants (4 males, 8 females) whose ages range from 37-71 years. The relations of patients are 5 spouses(3 husbands, 2 wives), 4 daughters-in-law, 2 daughters, and 1 son-in-law. The following are the care-givers' meaning of experiences that results of the study shows. The first is "psychological conflict". It contains the minds of getting angry, reproaching, being driven to dispair, blaming oneself, giving up lives, and being afraid, hopeless, and resigned. The second is "physical, social and psychological pressure" . At this stage, care-givers are shown to be under stress of both body and soul for the lack of freedom and tiredness. They also feel constraint because they hardly cope with the care and live through others' eyes. The third is "isolation". It makes the relationship of patient care-giver to be estranged, without understanding each other. They, also, experience indifference such as being upset and left alone. The forth is "acceptance" They gradually have compassion, bear up and then adapt themselves to the circumstances they are in. The fifth is "love". Now they learn to reward the other with love. It is also shown that this stage contains the process of winning others' recognition. The final is "hope". In this stage they really want situations to go smoothly and hope everything will be O.K. These consequences enable us to summarize the principles of cue experience such as, in the early stage, negative response such as physical·psychological confusion, pain and conflict are primary. Then the stage of acceptance emerges. It is an initial positive response phase when care-givers may admit their situations. As time passes by a positive response stage emerges. At last they have love and hope. Three stages we noted above : however, there are never consistent situations. Rather it gradually comes into the stage of acceptance, repeating continuous conflict, pressure and isolation. If any interest and understanding of families or the support of surrounding society lack, it will again be converted to negative responses sooner or later. Otherwise, positive responses like hope and love can be encouraged if the family and the surroundings give active aids and understanding. After all, the principles of dementia care experiences neither stay at any stage, nor develop from negative stages to positive stages steadily. They are cycling systems in which negative responses and positive responses are constantly being converted. I would like to suggest the following based on the above conclusions : First, the systematic and planned education of dementia should be performed in order to enhance public relations. Second, a special medical treatment center which deals with dementia, under government's charge, should be managed. Third, the various studies approaching dementia care experiences result in the development of more reasonable and useful nursing guidelines.

  • PDF