• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1371-1376
• /
• 2003

In the thermal power plant, the main steam temperature is typically regulated by the fuel flow rate and the spray flow rate, and the reheater steam temperature is regulated by the gas recirculation flow rate. However, Strictly maintaining the steam temperature can be difficult due to heating value variation to the fuel source, time delay changes in the main steam temperature, the change of the dynamic characteristics in the reheater. Up to the present time, PID Controller has been used to operate this system. However, it is very difficult to achieve an optimal PID gain with no experience, since the gain of the PID controller has to be manually tuned by trial and error. This paper focuses on tuning of the 2-DOF PID Controller on the DCS for steam temperature control using immune based multiobjective approach. The stable range of a 2-DOF parameter for only this system could be found for the start-up procedure and this parameter could be used for the tuning problem. Therefore tuning technique of multiobjective based on immune network algorithms in this paper can be used effectively in tuning 2-DOF PID controllers.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.278-281
• /
• 2008

This study demonstrates the advantages of a shear-free structure designed to modify vertical profiles of wind speed in the atmospheric surface layer. Computational fluid dynamics(CFD) software, FLUENT is used to interpret the velocity field modification around the structure and wind turbine. The shapes of shear-free structure, installed at upstream toward prevailing wind direction, would be fences, buildings and trees, etc. According to the simulation results, it is obvious that wind shear between heights of wind turbine's blades is decreased together with a speed-up advantage. This would lead decrease of periodic wind loading caused by wind shear and power-out increase by flow uniformity and wind speed-up.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2006.05a
• /
• pp.1328-1332
• /
• 2006

As the city is developed, Sewerage outlet is installed for the discharge of rainfall special at new town or modified the existed sewerage network. But the sewerage outlet is influenced to the cannel flow. In this paper, for analyzing variation of flow properties by installing sewerage outlet, it was experimented a with $120^{\circ}$ channel junction. The water depth is rapidly increasing at the just before sewerage installed position, but the velocity is represented increasing at the just after sewerage installed position. In addition, the biggest increment of water depth and velocity is represented $3.0m^3/hr{\sim}4.0.m^3/hr$. At the position of the sewerage outlet installation, separate install at up and downstream is rather than only one position at up or down stream. If it was not install both installation, the upstream installation is better than downstream installation.

• Bulletin of the Korean Mathematical Society
• /
• v.54 no.6
• /
• pp.2119-2139
• /
• 2017

Here, certain Ricci flow for Finsler n-manifolds is considered and deformation of Cartan hh-curvature, as well as Ricci tensor and scalar curvature, are derived for spaces of scalar flag curvature. As an application, it is shown that on a family of Finsler manifolds of constant flag curvature, the scalar curvature satisfies the so-called heat-type equation. Hence on a compact Finsler manifold of constant flag curvature of initial non-negative scalar curvature, the scalar curvature remains non-negative by Ricci flow and blows up in a short time.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.880-884
• /
• 1995

Manufacturing environment is getting characterized by unstable market demand,short product life cycle and timebased competition. For adapting this environment,machine tools have to be further versatile functionally in order to reduce part's set-up time. Unlike existing manufacturing systems mainly to focus on part flow, it is important to control tool flow using fast tool change device and tool delivery device in parallel machines consisting of versatile machine tools, because complete operations on a part can be performed on one machine tool in a single machine set-up. In this paper, under dynamic tool allocation strategy to share tools among machine tools, we propose a real-time tool allocation and operation esequence model with an objective of minimizing flow time using autonomy and negotiation of agents in parallel machines

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10b
• /
• pp.59-62
• /
• 2003

The precision cold forging of helical gear for steering pinion has been studied. Because of the large helix angle, there are many difficult problems to control the material flow and part dimension. The die shape was proposed to improve the flow of workpiece. In order to improve the dimensional accuracy of forged part, a FE analysis was performed. The proposed die shape drives to flow amicably workpiece. The applied load was reduced up to 10 percent, compared to the conventional-shaped-die. The elastic deformation of die has been investigated quantitatively by the 3-dimensional FE analysis. The die-land has been expanded up to $10{\mu}m$ on loading stage, based on the FEM results. Therefore, the elastic deformation amounts should be taken into consideration to improve the dimensional accuracy of forged helical gear.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.262-263
• /
• 2014

The purpose of this study was to investigate properties of high fluidity concrete adding waste marble powder. A change in the replacement ratios of waste marble powder was measured compressive strength and slump flow, O-Lot and U-Box. Waste marble powder has replaced binder of high fluidity concrete at certain contents of 0~20%. As a results, Slump flow, O-Lot and U-box adding waste marble powder up to 10% have increased by adding waste marble powder. As the concrete with a replacement ratio of waste marble powder up to 10% was found to have a compressive strength superior to that of plain.

• Journal of Ship and Ocean Technology
• /
• v.4 no.1
• /
• pp.1-10
• /
• 2000

A low-order potential based boundary element method is applied for the prediction of the performance of flapped rudders as well as all-movable rudders in steady inflow. In order to obtain a reasonable solution at large angles of attack, the location of the trailing wake sheet is determined by aligning freely with the local flow. The effect of the wake sheet roll-up is also included with use of a high order panel method. The flow in the gap of a flapped rudder is modeled as Couette flow and its effect is introduced into the kinematic boundary conditions for flux at both the inlet and the outlet of the gap. In order to validate the present method, the method is applied for a series of rudders and the computational results on forces and moments are compared with experimental data. The effect of the gap size on the forces and moments is also presented.

• Journal of Ocean Engineering and Technology
• /
• v.19 no.6 s.67
• /
• pp.1-7
• /
• 2005

This paper deals with the design and aerodynamic analysis of a special-type impulse turbine, with an end plate for wave energy conversion. Numerical analysis was performed using a CFD code, FLUENT. The main idea of the proposed end plate was to minimize the adverse effect of tip clearance of turbine blade, and was borrowed from ducted propeller, with so-called penetrating end plate for special purpose marine vehicles. Results show that efficiency increases up to $5\%$, depending on the flow coefficient; a higher flow coefficient yields increased efficiency. Decrease of input coefficient CAwith an end plate is the main reason for higher efficiency. Performance of end plate at various design parameters, as well as flow conditions, was investigated; the advantages and disadvantages of the presentimpulse turbine were also discussed.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.2
• /
• pp.281-289
• /
• 1992

In an attempt to simulate the flows in the computer hard disk storage system, flow visualization and quantification by image processing technique were applied. Model geometry was constructed while the dynamic similitude was maintained. Circumferential velocities were mapped out in the transient spin-up phase. During the spin-up phase, fluid close to the rotating inner hub approached the solid body rotation, while the fluid in the outer region showed the velocity deficit compared to the rotating speed of the disks. Effects of presence of read/write head arm assembly between the gap were studied by changing the location of the head. The experimental results could serve as a benchmark for the alidation of numerical codes.