• Journal of the Korea Society of Computer and Information
• /
• v.14 no.2
• /
• pp.157-168
• /
• 2009

In this paper, a photovoltaic system is designed with a step up chopper and single phase PWM(Pulse Width Modulation) voltage source inverter. Where proposed Synchronous signal and control signal was processed by one-chip microprocessor for stable modulation. The step up chopper operates in continuous mode by adjusting the duty ratio so that the photovoltaic system tracks the maximum power point of solar cell without any influence on the variation of insolation and temperature because solar cell has typical voltage and current dropping character. The single phase PWM voltage source the inverter using inverter consists of complex type of electric power converter to compensate for the defect, that is, solar cell cannot be developed continuously by connecting with the source of electric power for ordinary use. It can cause the effect of saving electric power. from 10 to 20[%]. The single phase PWM voltage source inverter operates in situation that its output voltage is in same phase with the utility voltage. In order to enhance the efficiency of photovoltaic cells, photovoltaic positioning system using sensor and microprocessor was design so that the fixed type of photovoltaic cells and photovoltaic positioning system were compared. In result, photovoltaic positioning system can improved 5% than fixed type of photovoltaic cells. In addition, I connected extra power to the system through operating the system voltage and inverter power in a synchronized way by extracting the system voltage so that the phase of the system and the phase of single-phase inverter of PWM voltage type can be synchronized. And, It controlled in order to provide stable pier to the load and the system through maintaining high lurer factor and low output power of harmonics.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.7
• /
• pp.655-661
• /
• 2006

Dielectric and piezoelectric properties of PMN-PZT ceramics with a high mechanical quality factor$(Q_m)$ and a low temperature sintering temperature were investigated as a function of PZN substitution in order to develop multilayer piezoelectric transformer for AC-DC converter. Multilayer piezoelectric transformers were subsequently manufactured using the PMN-PZN-PZT ceramic offering the optimal behavior and then the electrical performance were invetigated. At the sintering temperature of $940^{\circ}C$, density, electromechanical coupling factor$(k_p)$, mechanical qualify factor$(Q_m)$ and dielectric constant$(\varepsilon_r)$ of 8 mol% PZN substituted specimen were $7.73g/cm^3$, 0.524, 1573 and 1455, respectively. The PZN substitution caused a increase in the dielectric constant and the electromechnical coupling factor. The voltage step-up ratio of multilayer piezoelectric transformer showed the maximum value at near the resonant frequency of 76.55 kHz and increased according to the increase of load resistance. The multilayer piezoelectric transformer with the output impedance coincided with the load resistance showed the temperature increase of less than $20^{\circ}C$ at the output power of 10 W. Based on the results, the manufactured multilayer transformer using the low temperature sintered PMN-PZN-PZT ceramics can be stably driven for both step-up and down transformers.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.11
• /
• pp.1304-1310
• /
• 2010

This study is to design FMCW radar transceiver of K-band which is used to detect and track approaching high speed targets with low altitude. The transmitter needs high output power due to small RCS targets and wide beamwidth of transmit antenna. Multi-channel receivers are required to detect and track targets by interferometer method. Transmitter consists of high power amplifier, waveguide switch, and frequency up-converter. Receiver is composed of five channel receivers, up and down converters, X-band local oscillator and waveform generator. Before manufacturing it, the proposed architecture of transceiver is proved by modeling and simulation using several parameters. Then, it is manufactured by using industrial RF components. The performance parameters are measured through experiment. In the experiment, transmitting power and receiver gain were measured with 39.64 dBm and 29.1 dB, respectively. All other parameters in the specification were satisfied as well.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.10C
• /
• pp.813-819
• /
• 2008

In this paper, we implemented a real-time system which displays 3-dimensional (3D) stereoscopic image with stereo camera. The system consists of a set of stereo camera, FPGA board, and 3D stereoscopic LCD. Two CMOS image sensor were used for the stereo camera. FPGA which processes video data was designed with Verilog-HDL, and it can accommodate various resolutional videos. The stereoscopic image is configured by two methods which are side-by-side and up-down image configuration. After the left and right images are converted to the type for the stereoscopic display, they are stored into SDRAM. When the next frame is inputted into FPGA from two CMOS image sensors, the previous video data is output to the DA converter for displaying it. From this pipeline operation, the real-time operation is possible. After the proposed system was implemented into hardware, we verified that it operated exactly.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.6
• /
• pp.608-618
• /
• 2004

In this paper, modifying the diode star double balanced mixer of Maas, a novel resistive 60 GHz pHEMT MMIC star mixer is suggested. Due to star configuration, troublesome IF balun for ring configuration FET mixer is not necessary. In addition, the sysematic design method of dual balun through EM simulation is suggested rather than the design by inspection as Maas. The mixer circuit is fabricated as MMIC on CPW base using 0.1 um GaAs pHEMT Library of MINT in Dongguk University. The size is 1.5 ${\times}$ 1.5 $\textrm{mm}^2$ and its performance is adjustable by DC supply. It can be operated as both up and down converters and it shows the conversion loss of about 13∼18 ㏈ over the full V-band frequencies.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.1
• /
• pp.44-50
• /
• 2004

In this paper, a DBM(Doubly Balanced Mixer) of 2 GHz is implemented on FR4 substrate. The structure of doubly balanced mixer requires, in general, two batons and a quad diode. For balun, a novel planar balun using microstrip to CPS is suggested and designed. The suggested balun shows the phase imbalance of 180$^{\circ}$${\pm}$ 1.5$^{\circ}$and the amplitude imbalance of ${\pm}$ 0.2 ㏈ for 1.5 to 2.5 GHz. Using the balun, DBM is succesfully implemented, and the measured conversion loss of up/down converter show about 6 ㏈ over the bandwidth. The balun may be applicable for MMIC DBM with the process supporting backside via thourgh more study.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.5
• /
• pp.1053-1059
• /
• 2011

DMX512 protocol is a typical protocol which controls LED lighting system. It has a strong feature and can be used to a lot of lighting system. But LED control system with cable has a few problem because they have a lot of control cables. It is very difficult to set up the complex lighting. Furthermore if it is set up it is not easy to keep and recover the system from the out of order. So it is required Wireless Lighting Control System. This paper describes the proposal, design, and implementation of a novel method which can provide versatile light effects with the increased capability of the mobility and the number of universes for Wireless Lighting system. And then we implement experiment environment to control indoor lighting system controled by ZigBee and WLAN converter not having complicating control line. Data frames are transferred to DMX512 device by encapsulation and decapsulation to control color LED. In the same time give the method to solve the data bottleneck problem which can be comes out because of speed difference between Heterogeneous network and measure performance of control system.

• Nuclear Engineering and Technology
• /
• v.53 no.10
• /
• pp.3406-3412
• /
• 2021

A real-time digital time-stamp sorting algorithm used in the In-Beam positron emission tomography (In-Beam PET) is presented. The algorithm is operated in the field programmable gate array (FPGA) and a small amount of registers, MUX and memory cells are used. It is developed for sorting the data of annihilation event from front-end circuits, so as to identify the coincidence events efficiently in a large amount of data. In the In-Beam PET, each annihilation event is detected by the detector array and digitized by the analog to digital converter (ADC) in Data Acquisition Unit (DAQU), with a resolution of 14 bits and sampling rate of 50 MS/s. Test and preliminary operation have been implemented, it can perform a sorting operation under the event count rate up to 1 MHz per channel, and support four channels in total, count rate up to 4 MHz. The performance of this algorithm has been verified by pulse generator and ²²Na radiation source, which can sort the events with chaotic order into chronological order completely. The application of this algorithm provides not only an efficient solution for selection of coincidence events, but also a design of electronic circuit with a small-scale structure.

• Journal of Software Assessment and Valuation
• /
• v.16 no.2
• /
• pp.109-115
• /
• 2020

In this paper, the problem that occurs when negative voltage is generated using an inexpensive buck device in an IT device that is supplied with a single power by an adapter or battery is analyzed. For the cause analysis, the principle of operation of the buck device and the principle of the inverter circuit were examined, and the circuit characteristics of the inverter circuit were analyzed using the buck device. As a result of the analysis, it was confirmed that the inverter circuit using the buck device initially needs a large starting current, and in particular, in the case of a current capacity that is less than the starting current in the circuit that supplies power, it was confirmed that it could fall into a state similar to the latch-up phenomenon. In order to confirm the analysis result, an experimental circuit was constructed and the input current was checked. If the supply current is sufficient, it is confirmed that over-current flows and starts. If the supply current is insufficient, the circuit cannot start and a latch-up phenomenon occurs.

• Journal of electromagnetic engineering and science
• /
• v.3 no.2
• /
• pp.86-90
• /
• 2003

A flat conversion loss in microwave mixer is hard to achieve if integrating with an image rejection filter(IRF). This is due to the change of termination condition with respect to the LO and IF frequency at RF port where the filter has 50 ohm termination property only in the RF band. This paper describes a flatness maintenance in the down mixer concerning a diode matching condition as well as an electrical length of embedding line at RF port. The implemented single balance diode mixer is suitable for a 23 ㎓ European Terrestrial Radio. RF, LO and fixed IF frequency chosen in this paper are 21.2∼22.4 ㎓, 22.4∼23.6 ㎓ and 1.2 ㎓, respectively. The measured results show a conversion loss of 8.5 ㏈, flatness of 1.2 ㏈ p-p, input P1㏈ of 7㏈m, IIP3 of 15.42 ㏈m with nominal LO power level of 10㏈m. The return loss of RF and LO port are less than - 15 ㏈ and - 12 ㏈, respectively and IF port is less than - 6 ㏈. LO/RF and LO/IF isolation are 18 ㏈ and 50 ㏈, respectively. This approach would be a helpful reference for designing up/down converter possessing a filtering element.