• Journal of Power Electronics
• /
• 제19권2호
• /
• pp.363-379
• /
• 2019

Resonant converters have attracted a lot of attention because of their high efficiency due to the soft-switching performance. An isolated high step-up converter with secondary-side resonant loops is proposed and analyzed in this paper. By placing the resonant loops on the secondary side, the current stress for the resonant capacitors is greatly reduced. The power loss caused by the equivalent series resistance of the resonant capacitor is also decreased. Clamp diodes in parallel with the resonant capacitors ensure a unique discontinuous current mode in the converter. Under this mode, the active switches can realize soft-switching during both turn-on and turn-off transitions. Meanwhile, the reverse-recovery problems of diodes are also alleviated by the leakage inductor. The converter is essentially a step-up converter. Therefore, it is helpful for decreasing the transformer turn-ratio when it is applied as a high step-up converter. The steady-state operation principle is analyzed in detail and design considerations are presented in this paper. Theoretical conclusions are verified by experimental results obtained from a 500W prototype with a 35V-42V input and a 400V output.

• 한국전자통신학회논문지
• /
• 제15권5호
• /
• pp.889-896
• /
• 2020

일반적으로 스텝 업(Step-up) 컨버터는 Boost 컨버터, Buck-Boost 컨버터, Flyback 컨버터, Push-Pull 컨버터 등 다양하며 이 중에서 Boost 컨버터는 매우 간단한 형태로 가장 널리 사용되는 스텝 업(Step-up) 컨버터이다. 하지만, Boost 컨버터는 DCM 동작, 큰 리플 문제 및 RHPZ 문제 등을 가지고 있다. 이러한 문제를 해결하기 위해 새로운 Topology를 적용한 컨버터들이 제시되었는데 그 중 KY 컨버터는 Boost 컨버터의 DCM 동작, 큰 리플 문제 및 RHPZ 문제 등을 개선하였다. 그러나 기존의 KY 컨버터는 Boost 컨버터보다 전압 이득이 상대적으로 낮은 단점이 있다. 따라서 본 논문에서는 기존의 KY 컨버터의 장점이 있으면서 낮은 전압 이득 문제를 해결한 새로운 Topology의 KY 컨버터를 제안하였다.

• 전력전자학회논문지
• /
• 제18권4호
• /
• pp.342-348
• /
• 2013

In this paper, an improved non-isolated 3-level high step-up boost converter is proposed. By using the well known duality principle, the proposed converter is derived from two-phase buck converter. Compared with the traditional boost converter and 3-level boost converter, the proposed converter can obtain very high voltage conversion ratio and the voltage stress of switching devices and diodes is only 1/4 of the output voltage. A 1 kW prototype converter is built and tested to verify performances of the proposed converter.

• 전력전자학회논문지
• /
• 제20권5호
• /
• pp.464-470
• /
• 2015

In this paper, a non-isolated three-level high step-up boost converter with output voltage balancing is proposed. By adding one extra inductor to the conventional three-level boost converter, the proposed converter is derived. Compared with the traditional boost converter and the three-level boost converter, the proposed converter can obtain very high voltage conversion ratio, and the voltage and current stress of switching devices and diodes are reduced. A 2.7 kW prototype converter is built and tested to verify performances of the proposed converter.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2003년도 종합학술발표회 논문집 Vol.13 No.1
• /
• pp.366-370
• /
• 2003

This paper introduces a new design and fabrication technology of 28 GHz low-cost up and down converter modules for digital microwave radios, The design of the converter module is based on unit circuit blocks, which are to be characterized using a special test fixture. Based on the cascade analysis of the module the 28 GHz up and down converter modules have been designed and implemented. The measured module performance agrees with the cascade analysis. New components such as a tapped edge-coupled filter and a new Ka-band waveguide-to-microstrip transition, which are less sensitive to fabrication tolerances, have been used in the module implementation.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제4C권6호
• /
• pp.295-299
• /
• 2004

A new design technique of fabricating 40 GHz up-converter modules for digital microwave radios has been developed. The design of the up-converter module is based on unit circuit blocks, which are to be characterized using a special test fixture. The complete module design may be as simple as a cascade layout of these unit circuit blocks. Also, the 40 GHz up-converter module employs a new microstrip-to-waveguide transition and a tapped edge-coupled filter, which are less sensitive to fabrication tolerances.

• 전력전자학회논문지
• /
• 제28권1호
• /
• pp.8-14
• /
• 2023

This paper proposes a PFC converter with a double step-up function using an asymmetrical PWM scheme. For the conventional PWM scheme, the input voltage range, which maintains a double step-up function, is limited because the proposed converter has different voltage gains and characteristics when the duty ratio(D) is less than 0.5. The proposed converter has a constant voltage gain regardless of the magnitude of the input voltage and can achieve output voltage balancing by using the asymmetrical PWM scheme. A 1.6-kW prototype of the proposed converter was built and tested to verify the performance.

• Journal of Power Electronics
• /
• 제15권6호
• /
• pp.1468-1479
• /
• 2015

Renewable energy resources such as wind and photovoltaic power generation systems demand a high step-up DC-DC converters to convert the low voltage to commercial grid voltage. However, the high step-up converter using a transformer has limitations of high voltage stresses of switches and diodes when the transformer winding ratio increases. Accordingly, conventional studies have been applied to series-connect multioutput converters such as forward-flyback and switched-capacitor flyback to reduce the transformer winding ratio. This paper proposes new single-ended converter topologies of an isolation type and a non-isolation type to improve power efficiency, cost-effectiveness, and output ripple. The first proposal is an isolation-type charge-pump switched-capacitor flyback converter that includes an extreme-ratio isolation switched-capacitor cell with a chargepump circuit. It reduces the transformer winding number and the output ripple, and further improves power efficiency without any cost increase. The next proposal is a non-isolation charge-pump switched-capacitor-flyback tapped-inductor boost converter, which adds a charge-pump-connected flyback circuit to the conventional switched-capacitor boost converter to improve the power efficiency and to reduce the efficiency degradation from the input variation. In this paper, the operation principle of the proposed scheme is presented with the experimental results of the 100 W DC-DC converter for verification.

• Journal of Power Electronics
• /
• 제16권2호
• /
• pp.414-424
• /
• 2016

This paper proposes a novel high-efficiency high-step-up interleaved converter with a voltage multiplier, which is suitable for electric vehicle power management applications. The proposed interleaved converter is capable of achieving high step-up conversion by employing a voltage-multiplier circuit. The proposed converter lowers the input-current ripple, which can extend the input source's lifetime, and reduces the voltage stress on the main switches. Hence, large voltage spikes across the main switches are alleviated and the efficiency is improved. Finally, a prototype circuit with an input voltage of 24 V, an output voltage of 380 V, and an output rated power of 1 kW is implemented and tested to demonstrate the functionality of the proposed converter. Moreover, satisfying experimental results are obtained and discussed in this paper. The measured full-load efficiency is 95.2%, and the highest measured efficiency of the proposed converter is 96.3%.

• Journal of Power Electronics
• /
• 제16권5호
• /
• pp.1629-1638
• /
• 2016

Differential power processing (DPP) systems are among the most effective architectures for photovoltaic (PV) power systems because they are highly efficient as a result of their distributed local maximum power point tracking ability, which allows the fractional processing of the total generated power. However, DPP systems require a high-efficiency, high step-up/down bidirectional converter with broad operating ranges and galvanic isolation. This study proposes a single, magnetic, high-efficiency, high step-up/down bidirectional DC-DC converter. The proposed converter is composed of a bidirectional flyback and a bidirectional isolated switched-capacitor cell, which are competitively cheap. The output terminals of the flyback converter and switched-capacitor cell are connected in series to obtain the voltage step-up. In the reverse power flow, the converter reciprocally operates with high efficiency across a broad operating range because it uses hard switching instead of soft switching. The proposed topology achieves a genuine on-off interleaved energy transfer at the transformer core and windings, thus providing an excellent utilization ratio. The dynamic characteristics of the converter are analyzed for the controller design. Finally, a 240 W hardware prototype is constructed to demonstrate the operation of the bidirectional converter under a current feedback control loop. To improve the efficiency of a PV system, the maximum power point tracking method is applied to the proposed converter.