• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.5 no.6
• /
• pp.9-13
• /
• 2002

This study has been performed to investigate the physical and mechanical characteristics of compaction, volume change and compressive strength for reinforced soil mixed with cement. And confirm the reinforcing effects with admixture such as cement. To this end, a series of compaction test and compression test was conducted for clayey soil(CL) and cement reinforced soil. In order to determine proper moisture content and mixing ratio, pilot test was carried out for soil and cement reinforced soil. And the mixing ratio of cement admixture was fixed 3%, 6%, 9% and 12% by the weight of dry soil. As the experimental results, the maximum dry unit weight(${\gamma}_{dmax}$) was increased with the mixing ratio and then shown the peak at 10% reinforced soil, but the optimum moisture content(OMC) and the volume change was decreased with the ratio increase. And the compressive strength volume change was decreased with mixing ratio increased.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.05a
• /
• pp.93-98
• /
• 2005

The purpose of this study was to analyze the compression strength research by aerated concrete as mixing ratio This Study used foaming-agent and produced aerated concrete by pre-foam way that is used in construction site. An experiment changes unit cement amount, w/c and the glass fiber mixing rate and 'measured capacity change, unit capacity weight and compressive strength. The results obtained from experimental study are as following; Research to reduce unit capacity weight in condition more than unit cement amount 500kgf is considered should be gone side by side. The highest compressive strength result appeared in aerated concrete that cement amount 600kgf and w/c ratio $45\%$, $50\%$. compressive strength was increased maximum $34%$ when glass fiber $0.7\%$ addition cause by coherence enlargement to enlargement of cement paste and glass fiber addition per unit volume

• Journal of the Korea Institute of Building Construction
• /
• v.17 no.5
• /
• pp.393-401
• /
• 2017

This study presents an evaluation of basic properties of light weight mortar with expanded polystyrene bead(EPB) and waste expanded polystyrene(WEP) by varying replacement rations. In order to evaluate the basic properties of the light weight mortar with EPB and WEP, unit weight, compressive strength, flexural strength, water absorption ratio, thermal conductivity and distribution of polystyrene (EPB and WEP) in hardened mortar were performed. As a result, unit volume, compressive strength, bending strength, water absorption and thermal conductivity of light weight mortar were increased, but area distribution of polystyrene decreased with increasing the replacement ratio of WEP.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.5 no.6
• /
• pp.37-42
• /
• 2002

This study has been performed to investigate the physical and mechanical characteristics of compaction, volume change and compressive strength for reinforced soil mixed with polypropylene fiber, and to confirm the reinforcing effects with admixture such as polypropylene fiber. To this end, a series of compaction test and compression test was conducted for clayey soil(CL) and polypropylene fiber reinforced soil. In order to determine proper moisture contents and mixing ratio, pilot test was carried out for natural soil and PFRS(polypropylene fiber reinforced soil). And the mixing ratio of mono-filament fiber and fibrillated polypropylene fiber admixture was 0.1%, 0.3%, 0.5% and 1.0% by the weight of dry soil. From the experimental results, it was found that the optimum moisture contents(OMC) increased with the mixing ratio of fiber, but the maximum dry unit weight and the volume change was decreased with the mixing ratio. It means that the improvement of the workability and the reduction of the weight of embankment was done by the addition of the polypropylene fiber. And, from the compression test results, it was found that the addition of the polypropylene fiber remarkably improved the compressive strength of PFRS. And it was observed in the viewpoint of strength that the fibrillated polypropylene fiber reinforced soil was more effective than the mono-filament polypropylene fiber reinforced soil.

• Journal of the Korea Institute of Building Construction
• /
• v.7 no.2 s.24
• /
• pp.77-83
• /
• 2007

This study investigated the fundamental properties of the lightweight foamed concrete depending on various admixtures, and the results were summarized as following. When 20% of cement kiln dust(CKD) and 0.002% of stabilizing agent were mixed to lightweight foamed concrete, it was necessary to use a superplasticizer because flowability was decreased. However, it could reduce sinking depth which were the extensive trouble of lightweight foamed concrete. Bulk density was divided into '0.4' and '0.5' grades on KS according to unit volume weight. The compressive strength was less than that of plain concrete when admixtures were applied, but the results exceeded the minimum strength of the each grades on KS. Totally, it is found that the combination of 20% of CKD and 0.002% of stabilizing agent makes it possible to reduce a sinking depth, recycle resources, and save cost when were mixed.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.9 no.3
• /
• pp.17-25
• /
• 2006

To increase freeze-thaw resistance of porous concrete, this study examined physical properties of polymer by replacing paste used as a binding material with polymer, using unsaturated polyester and epoxy resin, and changing the mixing ratio of polymer. According to the result of this study, when the mixing ratio of resin paste to aggregates was 11 to 16%, voids volume was 33 to 37% and unit weight was about 1620 to 1720kg/$m^3$. In comparison with previous studies using cement paste, voids volume increased by about 7 to 16%, while unit weight decreased by about 100 to 300kg/$m^3$. Compressive strength was 90 to 155kg/$cm^2$ at the age of 7 days, which was 5-40kg/$cm^2$ bigger than porous concrete using cement paste. From a viewpoint of freeze-thaw resistance, it was identified that pluse velocity fell by 0.23km/sec, about 7% of the original velocity, when the cycle of freeze-thaw was repeated 300 times. In spite of 300 repetitions of the cycle, relative dynamic modulus of elasticity was more than 60%, which suggested that its freeze-thaw resistance was more excellent compared with the result that relative dynamic modulus of elasticity of porous concrete using cement paste was 60 % or less under the condition of 80 repetitions of freeze-thaw cycle.

• KIEAE Journal
• /
• v.13 no.6
• /
• pp.137-143
• /
• 2013

The purpose of this study is to suggest optimum micro-filler experiment method to select the optimal particle size of earth for using in earth construction works and test this suggestion through compressive strength measurement. According to the results of selecting the method to choose the optimum micro-filler mixing of earth and sand, three-stage filling(plate tamping) showed relatively high results and so was estimated to be the proper filling method. According to the results of optimum micro-filler experiment of earth and sand by the maximal sizes of sand, between 80% and 90% showed the highest result values. The larger the maximum size of sand was, the lower the addition ratio of sand was in optimum micro-filler mixing. According to the results of compressive strength experiment by the particle sizes of earth and sand, 90% in the addition ratio of sand showed the highest results, and so tended to be similar to the results of unit volume weight experiment.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.11a
• /
• pp.69-72
• /
• 2009

This research is focused on the applying of the foaming agent which can make the independent pore in the concrete structure in order to make a lightweight concrete structure. This lightweight foamed concrete can satisfy both the required strength and the mechanical properties as structural members. In addition, anti freezing-thawing properties also required. As a result of the unit volume-weight measurement, when the foaming agent mixed at 0.5% to 1%, the lightweight foamed concrete can be applied for the structural member. Also the density and compressive strength measurement results reveals that it will be suitable as structural member with 21MPa strength, when the density is betweenity8 to 1.9 and foaming agent quantities are 0.5% to 1%. Finally the result of freezing-thawing experiment, the effect freezing-thawing damage reduced according to adding foaming agent because those foaming agent make micro-pores in the structure which are not seen in the ordinary concrete structure.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.21 no.1
• /
• pp.49-59
• /
• 2019

In this study, the durability of conical pick cutter was compared and analyzed by pre- and post-test visual inspection, measurement of weight loss and wear volume through field test on two types of conical pick cutters applied to rotary drum cutter. In the visual inspection, it was found that only 9 inserts were lost in the slim type conical pick cutter. This result show that the thickness of the head cover surrounding a insert was important to maintain the insert during excavation. The weight loss and wear volume of the heavy type conical pick cutter were less than half that of the slim type. From these results, it can be confirmed that heavy type is more useful than slim type in hard rock. It should be noted that, when determining the wear loss of the conical pick cutter, the mutual comparison of the weight measurement and the wear volume measurement results may be different due to the unit weight of the material and the spalling caused by excavation.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.11a
• /
• pp.132-133
• /
• 2015

In this research by examining the influence that low quality aggregate has on the strength of concrete through testing, the lowering of strength according to use of low quality coarse aggregate was reviewed. The results showed that when using low quality coarse aggregate, due to the quality of aggregate a high volume of units was required, and this caused the compression strength to be lowered. In conclusion it was confirmed that if the low quality aggregate was used as is without mix correction this would lead to faulty construction and if the aggregate was corrected to about 60 kg/m3 mix correction, this would lead to an economically infeasible concrete mix.