• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.03a
• /
• pp.261-264
• /
• 1997

A single action press robot, which consists of a driving unit, rotator, up-down feed base and feed bar, is developed and applied for the press automation. The driving unit is made up with a face cam and blade cam, which have a phase angle. The feeding system consists of a double speed-up apparatus and linear motion guides, and has a fast motion characteristics. A horizontal feeding speed of the feed bar is increased twice by the double speed-up apparatus. The driving mechanism could be simplified due to the speed-up of the feeding unit.

• Proceedings of the KSR Conference
• /
• 2003.05a
• /
• pp.554-560
• /
• 2003

The transmission systems of high speed train serve in the severe condition compared with those of other trains, namely, they have to transmit high power to run with high speed and they have to make maximum use of the limited space. To clarify the capability of reduction gear unit for Korea High Speed Train, torque and temperature, vibration on the reduction gear unit were measured and test data were analyzed. This paper reports test methods and test results that performed to verify reliability of reduction gear unit during running test of Korea High Speed Train. It is confirmed from these results that the performance of reduction gear unit has not any problem.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.7
• /
• pp.679-686
• /
• 2013

The reduction unit is one of the most important components in railway cars, due to the transmission of torque from the motor to the wheels. Faulty reduction gears in high-speed trains result from excessive wear on the gear or damage to the gear. These types of gear defects have a significant effect on high-speed rail operation and safety; thus, a diagnosis system for the reduction unit is needed. Vibration diagnosis technology is one of the most effective diagnostics. In this paper, the vibration parameters of a reduction unit were evaluated during a driving-gear test and a full-vehicle test, using kurtosis and the crest factor. These tests were performed under normal operating conditions; a specimen tester was used to diagnose problems in defective gears.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.7
• /
• pp.694-701
• /
• 2013

The gear-reduction units of Korean high-speed trains consist of a motor reduction unit, an axle gear box reduction unit, and a tripod joint shaft. A reduction gear unit is a gearbox used to reduce the rotational speed of the input shaft to a slower rotational speed on the output shaft. This reduction in output speed helps to increase torque. Defective reduction gear units in high-speed trains are caused by damage to the gear or by gear fatigue. To diagnose potential problems, it is important to know the vibration characteristics of the reduction gear units. In this study, we analyzed the vibration characteristics of reduction gears under various conditions. The test setup included a full-scale test rig to evaluate reduction gear under both normal and extreme operating conditions.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.39 no.2
• /
• pp.1-5
• /
• 2002

Floating point unit system follows IEEE 754 Standard. In this paper, we used 1's complement system instead of 2's complement to practice the arithmetic. By converting we enable this system to compute simply and fast. To improve the speed of newly design adder, we used a transformation Carry selector adder of 53 bits. In paper, a design of floating point unit high efficiency micro processor system about for high speed. 

• Journal of Biosystems Engineering
• /
• v.17 no.4
• /
• pp.396-403
• /
• 1992

In order to operate a combine harvester at the optimum conditions and maximum performance, a forward speed control system(FSCS) was designed and develped. The FSCS consisted of engine, continuously variable V-belt transmission, threshing unit, traveling unit, detecting unit, and controller. Each components of the system were mathematically modeled. By a computer simulation, the effects of control parameters such as hydraulic piston speed, speed ratio, dead band of engine speed on the system performance were analysed, and the optimum control conditions were identified. The system appeared to be the most stable at the hydraulic piston speed of 10.6mm/s and the speed ratio of 0.4. The proper dead band of engine speed appeared to be 30rpm through the simulation and verification tests.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.422-425
• /
• 2008

Recently, electronic products and related parts are required to have thin thickness because of small form factor. To go with the trend, LGP(light guide plate) of LCD BLU(Liquid Crystal Display Back light unit: It is one of kernel parts of LCD) for cell phone has the thickness of 0.3 mm and the battery case of cell phone has 0.25 mm. Accordingly, high speed injection molding is required to make products which have thin thickness. High speed injection molding means that the resin is injected into the cavity at higher than normal speed avoiding short shot. In the case of hydro-mechanical high speed injection machine, it requires the design for hydraulic unit to make high injection speed and the design for control unit to control hydraulic unit. In the present paper, we concentrated on the molding stability of hydro-mechanical high speed injection machine to make an LGP of 0.3 mm thickness.

• Journal of Biosystems Engineering
• /
• v.21 no.4
• /
• pp.399-405
• /
• 1996

In order to maintain a constant speed ratio between the tractor and attached seed planter, a feedback control unit to rotate the feed shaft of the planter in proportional to the ground speed of the tractor was designed. The fifth wheel was used as a ground speed sensor for the unit. Using this control unit a feed shaft driving system was developed and tested to estimate its performance both in laboratory and fields. The test results showed that the system rotates the feed shaft proportionally to the ground speed in the range of the normal planting speed of 0.5-0.8m/s with errors less than 5%.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.7
• /
• pp.667-672
• /
• 2013

This paper presents the development of a condition monitoring system that monitors the operating conditions of a reduction unit, such as the bearing temperature, gearbox vibration, and gear oil deterioration, and notifies the operator of potential problems or abnormal conditions. A series of field tests on high-speed rail and conventional lines was performed to identify the characteristics of temperature rise and vibration levels on the reduction unit during operation. The monitoring system was designed based on the proper sensor selection, measurement method, and signal analysis to optimize the interface with the operating system of high-speed trains. Application of this monitoring system to high-speed trains will play an important role in their proper maintenance and safe operation.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.3 s.96
• /
• pp.103-108
• /
• 1999

A problem in the grinding with a small diametric wheel is the decrease of wheel speed. In order to resolve this problem, an accelerating unit which increases the wheel speed is recommended. In this paper, the accelerating effect of an accelerating unit has been investigated through the side-cut grinding experiments performed with a vitrified bonded CBN wheel in a machining center(MC). The static stiffness, normal force, and machining error were measured in the experiments. As the accelerating unit is attached on the column of machining center, the static stiffness of tool system is largely decreased. But as the wheel speed increased by the accelerating unit, this problem is overcome and machining efficiency is improved. The lesser the quill stiffness was, the higher the accelerating effect became.