• 한국분무공학회지
• /
• 제21권1호
• /
• pp.1-6
• /
• 2016

A gasoline injector rig which can measure cumulative injected fuel mass under a vehicle driving condition was developed. The measurement system consists of an engine control unit (ECU), data acquisition (DAQ) and injected fuel collection system using loadcells. By supplying reconstructed sensor signals which simulate the real vehicle's sensor signals to the ECU, the ECU drives injectors as if they were driven in the vehicle. The vehicle's performance was computer simulated by using $GT-Suite^{(R)}$ software based on both engine part load performance and automatic transmission shift map. Throttle valve position, engine and vehicle speed, air mass flow rate et al. were computer simulated. The used vehicle driving pattern for the simulation was FTP-75 mode. For reconstructing the real vehicle sensor signals which are correspondent to the $GT-Suite^{(R)}$ simulated vehicle's performance, the DAQ systems were used. The injected fuel was collected with mess cylinders. The collected fuel mass in the mess cylinder with elapsed time after starting FTP-75 driving mode was measured using loadcells. The developed method shows highly improved performance in fast timing and accuracy of the cumulative injected fuel mass measurement under the vehicle driven condition.

• 신재생에너지
• /
• 제3권2호
• /
• pp.24-30
• /
• 2007

The transient response of PEMFC (proton exchange membrane fuel cell) is important criteria in the application of PEM fuel cell to real automotive system. In this work, using a transparent unit PEM fuel cell, the transient response and cathode flooding during load change are investigated. The cell voltage is acquired according to the current density change($0.3Acm^2$ to $0.6A/cm^2$) under various stoichiometry conditions and different flooding intensities, Also the cathode gas channel images are obtained by CCD imaging system simultaneously. The different level of undershoots appeared at the moment of load changes under different cathode stoichiometries and flooding intensities. It takes about 1s that the product water comes up onto the flow channel so that oxygen supply is temporarily blocked which causes voltage loss in that "undershoot". The correlation of the dynamic behavior with stoichiometry and cathode flooding is induced from the results of these experiments.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 추계학술대회 논문집 학회본부
• /
• pp.91-94
• /
• 1996

A simulation procedure was developed for identifying Yungnam unit 2 excitation model parameters to improve the accuracy of stability simulation of KEPCO. First, generator model parameters are derived by using modified load rejection technique from measured load rejection test. For identifying excitation model parameters, switch was changed from MVR mode to AVR mode in Yungnam unit 2 excitation system instead of applying to a small step to the voltage reference($V_{ref}$) because of saving time and efforts, assuming the test result would show coincided result with applying to a small step to the $V_{ref}$. However, it was found that the response of switching from MVR to AVR is greatly different from it of applying small signal to the $V_{ref}$. A simulation procedure was needed to take into accounts of real AVR component status before and after switching from MVR to AVR. This paper reports the procedure which duplicated the measured response and addresses the merits of this test on conventional AVR step test.

• Journal of Electrical Engineering and Technology
• /
• 제5권4호
• /
• pp.552-560
• /
• 2010

This paper presents an application of layered Artificial Neural Network controller to study load frequency control problem in power system. The objective of control scheme guarantees that steady state error of frequencies and inadvertent interchange of tie-lines are maintained in a given tolerance limitation. The proposed controller has been designed for a two-area interconnected power system. Only one artificial neural network controller (ANN), which controls the inputs of each area in the power system together, is considered. In this study, back propagation-through time algorithm is used as neural network learning rule. The performance of the power system is simulated by using conventional integral controller and ANN controller, separately. For the first time comparative study has been carried out between SMES and CES unit, all of the areas are included with SMES and CES unit separately. By comparing the results for both cases, the performance of ANN controller with CES unit is found to be better than conventional controllers with SMES, CES and ANN with SMES.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 B
• /
• pp.793-796
• /
• 1996

This study proposes a new algorithm which performs a production simulation under various constraints and maintains computational efficiency. In order to consider the environmental and operational constraints, the proposed algorithm is based on optimization techniques formulated in LP form In the algorithm, "system characteristic constraints" reflect the system characteristics such as LDC shape, unit loading order and forced outage rate. By using the concept of Energy Invariance Property and two operational rules i.e. Compliance Rule for Emission Constraint, Compliance Rule for Limited Energy of Individual Unit, the number of system characteristic constraints is appreciably reduced. As a solution method of the optimization problem, the author uses Karmarkar's method which performs effectively in solving large scale LP problem. The efficiency of production simulation is meaningful when it is effectively used in power system planning. With the proposed production simulation algorithm, an optimal expansion planning model which can cope with operational constraints, environmental restriction, and various uncertainties is developed. This expansion planning model is applied to the long range planning schemes by WASP, and determines an optimal expansion scheme which considers the effect of supply interruption, load forecasting errors, multistates of unit operation, plural limited energy plants etc.

• 한국강구조학회 논문집
• /
• 제23권4호
• /
• pp.429-438
• /
• 2011

본 연구에서는 스트라치 시스템의 긴장설치과정 및 극한하중 해석을 수행하기 위한 명시적 해석법을 제안하였다. 스트라치 시스템은 Stressed-Arch에서 유래한 용어로 슬리브와 갭이 도입된 유동하현재 내부의 긴장재에 초기장력을 도입함으로써 갭이 점차 닫히게 되며, 이에 따라 상현재에 곡률이 도입되면서 전체 구조물이 상승하여, 최종적인 아치형태의 구조물을 형성하는 독창적인 구조시스템이다. 스트라치 시스템의 초기장력 도입과정을 긴장설치(stress-erection) 과정이라 하며, 초기곡률의 도입에 따라 유동 상현재에는 과도한 초기변형이 발생하여 소성거동에 의한 강체회전이 발생하는 불안정 구조물이 된다. 본 연구에서는 이러한 스트라치 시스템의 불안정 거동특성을 해석하기 위해서 강성행렬을 사용하지 않는 명시적 동적이완법을 사용하여 비선형 평형방정식의 해를 구하였고, 대변위 및 단면의 재료적 특성을 반영할 수 있는 필라맨트 보요소를 사용하여 연속된 상현재의 비선형 거동특성을 분석하였다. 필라맨트 보요소의 단면은 다수의 1차원 필라맨트로 구성되며, 각각의 필라맨트에 대해서 다양한 재료모델을 적용할 수 있다. 본 연구에서는 비선형 재료모델인 Ramberg-Osgood모델 및 Bi-linear 탄소성 모델을 적용하여 긴장설치 및 극한하중 해석을 수행하였고, 그 결과를 이전의 실험적 연구결과와 비교 분석하였다. 본 연구의 해석결과는 이전의 실험적 연구결과와 유사하였으며, 명시적 해석법의 특성상 효율적으로 후좌굴거동 특성까지 해석할 수 있었다.

• 한국물환경학회지
• /
• 제27권4호
• /
• pp.509-515
• /
• 2011

For this study the 4 sub-watersheds Okdong A, Hankang B, Jecheon A and Hankang C which are the main streams of the Han River within the mid-level region of Chungju Dam are selected and the analysis of soils has been carried out through the soil basic survey. When it comes to the soil erosion amount the soil nutrient load has been calculated by utilizing the RUSLE erosion equation. In case of the data related to the measurement of water flow and quality the information available from the "Water Information System" one of the websites run by the Ministry of Environment has been used to calculate the water pollution load. The correlation between the soil nutrient load and the water pollutant load has been analyzed through making comparison. According to the results related to the soil nutrient load of each sub-watershed the Hankang C shows the highest values TOC 29,986.92 ton/yr, TN 3,860.33 ton/yr and TP 973.97 ton/yr respectively. Even when it comes to the loads related to water quality the Hankang C shows also comparatively high values TOC 6,625.64 ton/yr, TN 7,335.01 ton/yrand TP 145.49 ton/yr respectively. The soil nutrient loads of the sub-watersheds are shown to increase towards the lower stream meaning the load increases in the order of Hankang CHankang B and Okdong A. When it comes to the water pollutant load the value goes up along down the water system meaning the load gets higher in the order of Hankang C, Hankang B and Okdong A while utilizing the mainstream within the mid-level region of Chungju Dam as the basis. The correlation study showed that the nutrient content of soil is proportional to the pollutant load in water with the strongest positive correlation with TOC.

• 한국공작기계학회논문집
• /
• 제17권6호
• /
• pp.111-117
• /
• 2008

An automation process of filter unit is presented for the application of the assembling procedure and dry furnace work. By that automation procedure, it is expected to enhance working environment such as reducing laboring load, harmful gas, and burning scald. Furthermore, this automation process also minimizes via standardization of manufacturing process so that it may increase productivity and reliability. An automation process of filter unit is presented for the application of the assembling procedure and dry furnace work. Filter automation process also gives a good quality and productivity by simplifying to only one line from the complicated process such as filter cutting$\rightarrow$ adhering$\rightarrow$fabricating in a very small space. It is found that a new conceptual design of dry furnace shows the better quality like uniform heat distribution compared to the conventional design. It is also found that the present design gives a better working environment by adding cooling system.

• 대한기계학회논문집
• /
• 제14권3호
• /
• pp.594-602
• /
• 1990

본 연구에서는 동력전달용 인벌류우트 원통치차(스퍼어 및 헬리컬 기어)의 강 도 및 각종 영향인자를 충분히 고려하면서 크기를 최소로 하는 치차장치의 설계법을 개발하고, 이 설계법을 기본으로 하여 퍼스널 컴퓨터 상에서 누구나 손쉽게 설계에 이 용할 수 있는 설계 시스템을 개발하여 그 평가를 수행한다.

• 조명전기설비학회논문지
• /
• 제28권6호
• /
• pp.21-29
• /
• 2014

In this paper examine the characteristics of the generator supplying the most significant electrical energy in some parts required to drive the vehicle, and it is focused on to fabricate a performance evaluation unit for developing alternator with better performance. Through performance tests in accordance with the electrical load of alternators that is made in Valeo Corp. and Denso Corp., which are currently applied by H Corp., the fabricated performance evaluation unit has measured the power generation amount of the electrical energy supplied from the alternator, and it was analyzed. On the basis of this result, and to understand the flow of electrical energy of the vehicle, furthermore, it is intended to verify the usefulness of the performance evaluation unit which is designed in this paper. In this paper, based on the mechanism of the proposed performance evaluation unit, it will try to learn the convergence technology that can be applied to the design of the performance evaluation unit of other components of the vehicle.