• 마이크로전자및패키징학회지
• /
• 제8권2호
• /
• pp.1-7
• /
• 2001

저열팽창성 금속인 Kovar표면을 유리와 접합하기에 적합한 spinel을 주상으로 하는 균일한 산화막을 형성할 수 있도록 $N_2/H_2$에 $H_2O$가 첨가된 분위기에서의 산화 거동에 대하여 조사하였다. Kovar 산화는 확산에 의해 지배되는 공정이며, 이때 산화 활성화 에너지는 31.61 kacl/mol 이었다. $600^{\circ}C$에서 열처리한 결과 spinel을 주상으로 하는 0.5 $mu extrm{m}$ 이하의 연속적이고 균일한 외부 산화막을 얻을 수 있었다. TEM 분석 결과 격자 상수가 7.9 $\AA$인 spinel 임을 확인할 수 있었다. 그러므로, 가습된 $N_2/H_2$분위기에서 산화한 Kovar는 유리와 접합에 적용 가능할 것으로 판단된다.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권3호
• /
• pp.291-297
• /
• 1995

The InP crystals have been grown by modified synthesis solute diffusion (SSD) method and its properties have been investigated. The crystals have been grown by lowering the crucible quartz for growth in the furnace and crystal growth rate is 1.8mm/day. The lattice constant a. of the grown crystals is 5.867.angs.. Etch pits density along growth direction of crystal changes from 3.0*10.sup 3/cm$\^$-2/ of first freeze part to 6.7*10$\^$4/cm$\^$-2/ of last freeze part and the radial direction of wafer shows nearly uniform distribution. The resistivity and the carrier concentration of the grown crystals are 1.43*10$\^$-1/.ohm.-cm, 7.7*10$\^$15/cm$\^$-3/ at room temperature, respectively. In the photolurninescence at 10K, the radiation transitions are observed by the near band edge recombination, a pair recombination due to Si donor - Zn acceptor and its phonon replica in the InP. The activation energy by Zn diffusion in undoped n-InP crystals is 1.22eV.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.87-89
• /
• 2005

$Bi_{3.25}Y_{0.75}Ti_{3}O_{12}$[BYT] ferroelectric thin films were deposited by RF-Sputtering method on the $Pt/Ti/SiO_2/Si$. We investigated the effects of processing condition (especially post-annealing) on the structural and ferroelectric properties of the BYT thin films. Increasing the annealing temperature, the peak intensity of (117) increased and c-axis orientation decreased. The BYT thin films crystallized well at $600^{\circ}C$ for 30min. No secondary phases observed in the XRD pattern. At annealing temperature of $700^{\circ}C$, the thin films had no cracks and the grain was uniform. The calculated lattice constants of BYT thin films were a=0.539nm, b=0.536nm, c=3.288nm. The remnant polarization of the $Bi_{3.25}Y_{0.75}Ti_{3}O_{12}$ capacitor reached $1.8uC/cm^2$ at an applied field about 400kV/cm. The BYT thin films can be used as capacitors in Ferroelectric Random Access Memory device.

• 한국전기전자재료학회논문지
• /
• 제21권3호
• /
• pp.242-248
• /
• 2008

The structural, optical and electrical properties of ZnO films doped with 1.5 at% of 3A materials(B, Al, Ga, In) were studied by sol-gel process. The films were found to be c-axis (002) oriented hexagonal structure on glass substrate, when post heated at 500 $^{\circ}C$. The surface of the films showed a uniform and nano size microstructure and the crystalline size of doped films decreased. The lattice constants of ZnO:B/Al/Ga increased than that of ZnO, while ZnO:In decreased. All the films were highly transparent(above 90 %) in the visible region. The energy gaps of ZnO:B/Al/Ga were increased a little, but that of ZnO:In was not changed. The resistivities of ZnO:Al/Ga/In were less than 0.1 $\Omega$cm. All the films showed a semiconductor properties in the light or temperature, however ZnO:In was less sensitive to it. A figure of merit of ZnO:In had the highest value of 0.025 $\Omega^{-1}$ in all samples.

• 센서학회지
• /
• 제18권4호
• /
• pp.311-315
• /
• 2009

This paper describes the characteristics of a poly 3C-SiC micro heater which was fabricated on AlN(0.1 $\mu$m)/3C-SiC(1.0 $\mu$m) suspended membranes by surface micro-machining technology. The 3C-SiC and AlN thin films which have wide energy band gap and very low lattice mismatch were used sensors for high temperature and voltage environments. The 3C-SiC thin film was used as micro heaters and temperature sensor materials simultaneously. The implemented 3CSiC RTD(resistance of temperature detector) and the power consumption of micro heaters were measured and calculated. The TCR(thermal coefficient of the resistance) of 3C-SiC RTD is about -5200 ppm/$^{\circ}C$ within a temperature range from 25 $^{\circ}C$ to 50 $^{\circ}C$ and -1040 ppm/$^{\circ}C$ at 500 $^{\circ}C$. The micro heater generates the heat about 500 $^{\circ}C$ at 10.3 mW. Moreover, durability of 3C-SiC micro heaters in high voltages is better than Pt micro heaters. A thermal distribution measured and simulated by IR thermovision and COMSOL is uniform on the membrane surface.

• Transactions on Electrical and Electronic Materials
• /
• 제8권4호
• /
• pp.149-152
• /
• 2007

[ $(Ba_{0.6}Sr_{0.3}Ca_{0.1})TiO_3$ ](BSCT) thick films doped with 0.1 mol% $MnCO_3\;and\;Yb_2O_3(0.1{\sim}0.7mol%)$ were fabricated by the screen printing method on the alumina substrates. And the structural and electrical properties as a function of $Yb_2O_3$ amount were investigated. The exothermic peak was observed at around $680^{\circ}C$ due to the formation of the poly crystalline perovskite phase. The lattice constants of the BSCT thick film doped with 0.7 mol% is 0.3994 nm. The specimen doped with 0.7 mol% $Yb_2O_3$ showed dense and uniform grains with diameters of about $4.2{\mu}m$. The average thickness of all BSCT thick films was approximately $70{\mu}m$. Relative dielectric constant and dielectric loss of the specimen doped with 0.7 mol% $Yb_2O_3$ were 2823 and 3.4%, respectively. The Curie temperature of the BSCT thick films doped with 0.1 mol% $Yb_2O_3$ was $46^{\circ}C$.

• Computers and Concrete
• /
• 제30권5호
• /
• pp.323-337
• /
• 2022

This paper proposes a numerical model to simulate the rotational behavior of steel fiber in fresh cement-based materials in the presence of a magnetic field. The results indicate that as the aspect ratio of fiber increases, the required minimum magnetic field intensity to make fiber rotate in viscous fluid increases. The optimal magnetic field intensity is 0.03 T for aligning steel fiber in fresh cement-based materials to ensure that the applying time of the magnetic field can be conducted concurrently with the vibrating process to increase the aligning efficiency. The orientation factor of steel fiber in cement mortar can exceed 0.85 after aligning by 0.03 T of the uniform magnetic field. When the initial angle of the fiber to the magnetic field direction is less than 10°, the magnetic field less than 0.03 T cannot make the fiber overcome the yield stress of fluid to rotate. The coarse aggregate in steel fiber-reinforced concrete is detrimental to the rotation and alignment of the steel fiber. But the orientation factor of ASFRC under the 0.03T of the magnetic field can also exceed 0.8, while the orientation factor of SFRC without magnetic field application is around 0.6.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.250-254
• /
• 2002

Intergranular corrosion of austenitic stainless steels is a conventional and momentous problem during welding and high temperature use. One of the major reasons for such intergranular corrosion is so-called sensitization, i.e., chromium depletion due to chromium carbide precipitation at grain boundaries. Conventional methods for preventing sensitization of austenitic stainless steels include reduction of carbon content in the material, stabilization of carbon atoms as non-chromium carbides by the addition of titanium, niobium or zirconium, local solution-heat-treatment by laser beam, etc. These methods, however, are not without drawbacks. Recent grain boundary structure studies have demonstrated that grain boundary phenomena strongly depend on the crystallographic nature and atomic structure of the grain boundary, and that grain boundaries with coincidence site lattices are immune to intergranular corrosion. The concept of "grain boundary design and control", which involves a desirable grain boundary character distribution, has been developed as grain boundary engineering. The feasibility of grain boundary engineering has been demonstrated mainly by thermomechanical treatments. In the present study, a thermomechanical treatment was tried to improve the resistance to the sensitization by grain boundary engineering. A type 304 austenitic stainless steel was pre-strained and heat-treated, and then sensitized, varying the parameters (pre-strain, temperature, time, etc.) during the thermomechanical treatment. The grain boundary character distribution was examined by orientation imaging microscopy. The intergranular corrosion resistance was evaluated by electrochemical potentiokinetic reactivation and ferric sulfate-sulfuric acid tests. The sensitivity to intergranular corrosion was reduced by the thermomechanical treatment and indicated a minimum at a small roll-reduction. The frequency of coincidence-site-lattice boundaries indicated a maximum at a small strain. The ferric sulfate-sulfuric acid test showed much smaller corrosion rate in the thermomechanically-treated specimen than in the base material. An excellent intergranular corrosion resistance was obtained by a small strain annealing at a relatively low temperature for long time. The optimum parameters created a uniform distribution of a high frequency of coincidence site lattice boundaries in the specimen where corrosive random boundaries were isolated. The results suggest that the thermomechanical treatment can introduce low energy segments in the grain boundary network by annealing twins and can arrest the percolation of intergranular corrosion from the surface.

• 한국광물학회지
• /
• 제28권1호
• /
• pp.9-16
• /
• 2015

통영산 해수양식진주를 광택과 모양에 따라 광택이 좋고 둥근(LR; Luster Round) 진주, 광택이 나쁘고 둥근(LLR; LackLuster Round) 진주, 바로크(LLB; LackLuster Baroque) 진주, 이핵(LTN Lackluster Two Nucleus) 진주로 세분하여 비중 측정, 현미경관찰, X선 회절분석, 주사전자현미경관찰 등을 통해 진주의 광택에 영향을 미치는 요인에 대한 광물학적 연구를 수행하였다. 광택이 좋은 진주는 광택이 나쁜 진주에 비해 비중이 약간 낮았지만 모두 상업적인 진주의 비중 내에 포함된다. 진주층 단면의 두께는 광택이 좋고 둥근 진주는 0.3 mm 정도로 균질한 반면, 광택이 나쁘고 둥근 진주는 각각의 진주층 두께는 균일하나 광택이 좋고 둥근 진주에 비해 두께가 얇다. 이핵 진주와 바로크 진주는 한 진주 내에서도 진주층 두께 편차가 상당히 큰 경향을 보였다. 진주의 표면은 광택이 좋은 진주가 광택이 나쁜 진주에 비해 아라고나이트 결정의 성장선이 좁고 선명하다. 광택이 좋은 진주는 광택이 좋지 않은 진주보다 아라고나이트 결정층의 결함이 적으며 배열이 평행하며 두께가 더 얇고, 표면과 내부에서 두께 차이가 작다. 능주층이 있는 경우 능주층과 진주층에서 아라고나이트 이외에 방해석이 포함되며, 광택이 나쁜 경우 방해석 함량이 매우 높다. 능주층이 없는 진주에서는 광택 여부에 상관없이 방해석이 없고 모두 아라고나이트로 구성되어 있다.

• 대한기계학회논문집A
• /
• 제35권11호
• /
• pp.1471-1476
• /
• 2011

자동차 배기계의 앞쪽에 배치된 촉매변환기는 배기가스 중 유해한 성분을 무해한 것으로 변환하는 제품이다. 이것의 중심부인 담체는 단면의 윤곽이 원형이나 타원형이고 내부는 미세한 격자형 벽으로 채워진다. 담체를 매트로 두르고 캔에 넣는 캐닝공정 중 과대한 압력을 받아서 담체가 취성파괴될 것이 염려된다. 담체의 파괴를 방지하고자 매트의 압력의 분포를 예측하는 유한요소 프로그램을 개발하였다. 이것은 Microsoft EXCEL로 작성되어 입출력이 모두 간편하다. 담체는 강체, 캔은 선형탄성체로 단순하게 취급하고 매트의 재료비선형성을 고려하였다. 캔은 굽힘과 균일인장이나 압축에 저항하는 것으로 모델링하였다. 편의상 요소의 갯수는 35개, 반복 횟수는 20회로 제한하였다. ABAQUS의 해석결과와 잘 일치하여 본 프로그램의 타당성을 입증하였다.