• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표대회 논문집(III)
• /
• pp.725-730
• /
• 1998

Recently, non-destructive tests are getting popular in evaluating concrete properties without braking specimens. Among several NDT methods, P-wave velocity measurement technique has been widely used to evaluate the stiffness and strength of concrete. The purpose of this study is to investigate factors influencing P-wave velocity measured by impact-resonant method and ultrasonic pulse velocity method, such as moisture content of concrete, existence and size of coarse aggregates, sensor and sampling rate. Test results show that rod-wave velocity measured by impact-resonant method and ultrasonic pulse velocity are significantly affected by the moisture content of concrete, i.e., the lower moisture content, the lower velocity. Moisture content influences rod-wave velocity stronger than ultrasonic pulse velocity. Rod-wave velocity is faster in concrete than in mortar and is also faster in concrete containing small size aggregates. Sensor and sampling rate have little influence on velocity.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2015년도 춘계 학술논문 발표대회
• /
• pp.224-225
• /
• 2015

Ultrasonic velocity method is applied to measure and correlate the strength of concrete to the velocity of the ultrasonic wave. With voids inside, mortar specimens may show the lower strength and it is intended to detect such change using the ultrasonic velocity method in this study. The amount of voids was varied and the measured data represented the condition of the mortar with voids. The test results can be used to predict the strength of concrete with voids using ultrasonic velocity method.

• Structural Engineering and Mechanics
• /
• 제65권5호
• /
• pp.601-609
• /
• 2018

Steel bolts are used in the construction industry for a large variety of applications that range from fixing permanent installations to temporary fixtures. In the past much research has been focused on developing destructive testing techniques to estimate their pull-out load carrying capacity with very little attention to develop non-destructive techniques. In this regards the presented research work details the combined use of ultrasonic pulse velocity and Schmidt hammer tests to identify anchor bolts with faculty installation and to estimate their pull-out strength by relating it to the Schmidt hammer rebound value. From experimentation, it was observed that the load capacity of bolt depends on its embedment length, diameter, bond quality/concrete strength and alignment. Ultrasonic pulse velocity test is used to judge the quality of bond of embedded anchor bolt by relating the increase in ultrasonic pulse transit time to the presence of internal pours and cracks in the vicinity of steel bolt and the surrounding concrete. This information combined with the Schmidt hammer rebound number, R, can be used to accurately identify defective bolts which resulted in lower pull-out strength. 12 mm diameter bolts with embedment length of 70 mm and 50 mm were investigated using constant strength concrete. Pull-out load capacity versus the Schmidt hammer rebound number for each embedment length is presented.

• 콘크리트학회논문집
• /
• 제11권4호
• /
• pp.157-167
• /
• 1999

Among several non-destructive testing methods, ultrasonic pulse velocity method and rebound index method have been widely used for the evaluation of concrete strength. However, such methods might not provide accurate estimated results since factors influencing the relationship between strength and either ultrasonic pulse velocity or rebound index are not considered. In this paper, the evaluation method of concrete strength using rod-wave velocity measured by impact-resonance method is proposed. A basic equation is obtained by the linear regression of velocity vs, strength data at specific age and then, aging factor is employed in the equation to consider the difference of the increasing rate between wave velocity and strength. Strengths predicted by the proposed equation agree well with test results. Furthermore, the combined method of rod-wave velocity and rebound index is proposed.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 봄 학술발표회논문집(II)
• /
• pp.707-711
• /
• 1998

Ultrasonic test usually was used for defect detection, crack depth measurements and strength estimation of hardened concrete. The essence of the pulse velocity method is that the transition time of an ultrasonic longitudinal pulse is measured in concrete. Ultrasonic velocity was propagated to the age of concrete, made a radical change at that time when concrete was setted. This study which monitored the change in a concrete by ultrasonic test was performed to estimate initial setting and final setting.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 봄 학술논문 발표대회
• /
• pp.55-56
• /
• 2023

Recently, large and high-rise buildings are increasing, and accordingly, concrete weight reduction is required. Lightweight aggregate concrete can provide economic feasibility and large space, but safety can be reduced due to problems such as low strength and poor durability. Since the development of such low strength of concrete is important in the early construction stage, it is necessary to evaluate the vertical formwork demolding period at the early age. The correlation was analyzed by measuring the compressive strength and ultrasonic pulse velocity. As a result, the ultrasonic pulse rates of normal and lightweight aggregate concrete at the time of 5 MPa expression, which is the time of vertical mold deformation, were 3.07 km/s and 2.77 km/s for W/B 41, and 2.89 km/s and 2.73 km/s for W/B 33.

• 한국건축시공학회지
• /
• 제23권6호
• /
• pp.683-692
• /
• 2023

본 연구에서는 보통 및 경량 굵은 골재를 사용한 콘크리트의 역학적 특성을 평가하기 위해 압축강도와 초음파 속도를 측정하였다. 압축강도에서는 재령 초기에서 보통골재 콘크리트가 높은 경향을 나타냈으나 시간 경과에 따라 경량골재 콘크리트가 높아지는 것을 알 수 있으며, 경량골재의 특징 중 높은 흡수율의 영향이라고 판단된다. 초음파 속도에서는 일정 시간을 제외하고 대부분 보통골재가 높은 경향을 나타냈으며, 골재의 내부 공극의 차이라고 판단된다. 압축강도와 초음파 속도의 상관관계를 통한 예측식의 상관계수(R²)가 0.95를 상회하며, 본 실험을 통한 예측식으로 강도 예측의 신뢰성이 높다고 판단된다.

• 비파괴검사학회지
• /
• 제37권2호
• /
• pp.84-90
• /
• 2017

An ultrasonic synthetic aperture focusing technique (SAFT) using a root mean square (RMS) velocity model is proposed for pulse-echo immersion testing to improve the computational efficiency. Considering the immersion ultrasonic testing of a steel block as an example, three kinds of imaging were studied (B-Scan, SAFT imaging based on ray tracing technology and RMS velocity). The experimental results show that two kinds of SAFT imaging have almost the same imaging performance, while the efficiency of RMS velocity SAFT imaging is almost 25 times greater than the SAFT based on Snell's law.

• 비파괴검사학회지
• /
• 제19권5호
• /
• pp.363-368
• /
• 1999

시험체의 두께나 초음파 속도를 측정하기 위해서 초음파 펄스-에코법이 널리 사용되고 있다. 초음파 속도를 결정하기 위해서는 초음파 송수신 장치를 포함한 오실로스코우프와 같은 초음파 측정 장치를 사용하여 시험편에서의 초음파진행 시간을 측정하고, 초음파 진행 거리에 해당하는 시험편의 두께를 버어니어 캘리퍼스 또는 마이크로미터와 같은 길이측정 도구를 사용하여 측정한다. 그리고 초음파를 이용하여 시험편의 두께를 측정할 때에는 초음파 속도를 알고 있는 대비 시험편으로 기준을 설정하여야 한다. 본 연구에서는, 대비 시험편 없이 재료의 두께와 초음파 속도를 동시에 구하는 방법을 제시하였다. 재질과 두께를 달리한 여러 시험편에서 측정된 초음파 속도와 두께가 기존의 방법에 의해 측정한 값과 잘 일치하였다.

• Computers and Concrete
• /
• 제4권6호
• /
• pp.477-497
• /
• 2007

The ultrasonic pulse velocity method has been widely used to evaluate the quality of concrete and assess the structural integrity of concrete structures. But its use for predicting strength is still limited since there are many variables affecting the relationship between strength and pulse velocity of concrete. This study is focused on establishing a complicated correlation between known input data, such as pulse velocity and mixture proportions of concrete, and a certain output (compressive strength of concrete) using artificial neural networks (ANN). In addition, the results predicted by the developed multilayer perceptrons (MLP) networks are compared with those by conventional regression analysis. The result shows that the correlation between pulse velocity and compressive strength of concrete at various ages can be well established by using ANN and the accuracy of the estimates depends on the quality of the information used to train the network. Moreover, compared with the conventional approach, the proposed method gives a better prediction, both in terms of coefficients of determination and root-mean-square error.