• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.9 no.1
• /
• pp.25-30
• /
• 2013

The periodic inspection of piping and pressure vessels welds in nuclear power plant has to provide reliable result related to weld flaws, such as location, maximum amplitude response, ultrasonic length, height and finally the nature or flaw pattern. The founded flaw in ultrasonic inspection is accepted or rejected based on these data. Specially, the amplitude of flaw response is used as basic parameter for flaw sizing and it may cause some deviation in length sizing result. Currently the ultrasonic inspections in nuclear power plant components are performed by specific inspection procedure which describing inspection technique include inspection system, calibration methodology and flaw characterizing. To perform ultrasonic inspection during in-service inspection, reference gain should be established before starting ultrasonic inspection by the requirement of ASME code. This reference gain used as basic criteria to evaluate flaw sizing. Sometimes, a little difference in establishing reference gain between calibration and field condition can lead to deviation in flaw sizing. Due to this difference, the inspection result may cause flaw sizing error. Therefore, the objective of this study is to compare and evaluate the ultrasonic amplitude difference between air filled and water filled pipe in nuclear power plant. Additionally, the accuracy of flaw sizing is estimated by comparing both conditions.

• Journal of Applied Reliability
• /
• v.17 no.3
• /
• pp.236-245
• /
• 2017

Purpose: There is no established inspection system for composite wind blade during the fabrication stage even though the blades are one of the most important part at wind generation system, but phased array ultrasonic testing method has been continuously studied about wind turbine blade with composite. When wind turbine blade with complex shape by phased array probe is inspected, it is necessary to study for system keeping constant pressure using pressure device. Methods: In this paper, we propose constant pressure device for inspecting wind turbine blade by phased array ultrasonic test method. Design of the device controller is based on Hunt-Crossley model. We evaluate reliability of phased array ultrasonic inspection result that applicated constant pressure device. Result: Defect indication is precise and its error is small when constant pressure mechanism based on Hunt-Crossley model was used. Conclusion: When inspection is progressed using constant pressure mechanism, the reliability of composite wind blade inspection can be improved.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.3
• /
• pp.82-88
• /
• 2003

The nondestructive internal quality evaluation of agricultural products has been strongly required from the needs for individual inspection. Recently, the ultrasonic wave has been considered as a solution fur this problem, and an ultrasonic system was constructed for the ultrasonic NDE of fruits and vegetables in our previous work. In this paper, the practical applicability of our ultrasonic system is tested fur the inspection of internal defects (central cavity) in Atlantic potato. Sound speed and RMS of transmitted ultrasonic wave signal were measured and classification algorithm using 2 dimensional stochastic analysis. was presented. Experimental results showed greater value of sound speed and RMS (root mean square) of transmitted signal in normal samples than in abnormal samples with cavity. Also a stochastic method to distinguish normal and abnormal showed fault detection rate less than 5%.

• International Journal of Reliability and Applications
• /
• v.5 no.1
• /
• pp.25-36
• /
• 2004

Ultrasonic inspection system consist of the examination procedures, equipment, and operators. The reliability of nondestructive testing is influenced by the inspection environment, materials and types of defect. It is very difficult to estimate the reliability of NDT due to the various factors. Piping inspection round robin was conducted to quantify the capability of ultrasonic inspection during in-service. In this study, the models for predicting the ultrasonic NDE reliability by logistic model and linear regression model are discussed. The utility of the NDT reliability assessment is verified by the analysis of the data from round robin test with these models.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.04a
• /
• pp.73-78
• /
• 2003

Ultrasonic measurement is one of important technologies in the lift-time maintenance of nuclear poler plant. Ultrasonic inspection system is consisted of the operator, equipment and procedure. The reliability of ultrasonic inspection system is affected by its ability. The performance demonstration round robin was conducted to quantify the capability of ultrasonic inspection for in-service. The small number of teams who employed procedures that met or exceeded ASME Sec. XI Code requirements detected the piping of nuclear power plant with various cracks to evaluate the capability of detection and sizing. In this paper, the statistical reliability assessment of ultrasonic nondestructive inspection data using Monte Carlo simulation is presented. The results of the probability of detection (POD) analysis using Monte Carlo simulation are compared to these of logistic probability model. In these results, Monte Carlo simulation was found to be very useful to the reliability assessment f3r the small hit/miss data sets.

• Journal of Welding and Joining
• /
• v.23 no.5
• /
• pp.43-48
• /
• 2005

Conventional non-destructive techniques for inspection of the weld in pipelines require significant test time and high cost. Ultrasonic guided waves have been widely studied and successfully applied to various non-destructive tests with advantage of the long-range inspection. In this paper, a study on the application of ultrasonic guided waves to the long-range inspection of the pipeline is presented using a long-range guided wave inspection system, Wavemaker SE16, GUL. The characteristics and setup of the long-range guided wave inspection system and experimental results in pipes of with various diameter are introduced. The experimental results in mock-up pipes with cluster type detects show that the minimum detectable wall thickness reduction with this guided wave system is $2\~3\%$ in the pipe cross section area. And the wall thickness reduction of $5\%$ in cross section area can be detected when actual detection level is used. Therefore, the applicability of the guided wave systeme to long-range inspection of wall thickness reduction in pipes is verified.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.2
• /
• pp.145-152
• /
• 2009

Currently almost all in-service-inspection techniques, applied in domestic nuclear power plants, are partial to field inspection technique. These kinds of techniques are related to managing nuclear power plants by the operation of foreign-produced inspection devices. There have been so many needsfor development of native in-service-inspection device because there is no native diagnosis device for nuclear power plant inspection yet in Korea. In this research, we developed several core techniques to make an automated ultrasonic pipe inspection system for nuclear power plants. A high performance multi-channel ultrasonic pulser/receiver module, an A/D converter module and a digital main CPU module were developed and the performance of the developed modules was verified. The S/N ratio, noise level and signal acquisition performance of the developed modules showed proper level as we designed in the beginning.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.240-245
• /
• 2001

Ultrasonic inspection system is consisted of the operator, equipment and procedure. The reliability of results in ultrasonic inspection is affected by its ability. Furthermore, the reliability of nondestructive testing is influenced by the inspection environment, other materials and types of defect. Therefore, it is very difficult to estimate the reliability of NDT due to various factors. In this study, the probability of detection, used logistic probability model and Monte Carlo simulation, estimated the reliability of ultrasonic inspection. The utility of the NDT reliability assesment is verified by the analysis of the data from round robin test applied these models.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.327-328
• /
• 2006

Recently, as the infocomindustry is developed, the semiconductor industry as well as the optical industry such as the optical communication and the optical instrument is developed rapidly. The transmission, storage and processing of information has been reaching an limit because amounts of information increase rapidly. The more quickly the optical communication is developed, the more sharply the demand of optical elements increase. The transport and inspection process is time consuming and the error rate is high, because this process are not automated in case of an optical lens. In this paper, the pick-up system that can hold optical elements and be transferred by the ultrasonic transport system is developed. The inspection system that distinguishes between the existence and the nonexistence of a defect is connected easily to pick-up system. The pick-up system separates the optical glass lens by results of the inspection. The automation program is developed by visual c++ programming.

• Journal of the Semiconductor & Display Technology
• /
• v.18 no.4
• /
• pp.143-148
• /
• 2019

Numerous pipe lines can be found on various plant-based industrial sites. These pipelines should be periodically checked for defects. Most of these pipelines are internally inaccessible and difficult to visually inspect. Therefore, the inspection is being carried out with the help of non-contact inspection equipment such as ultrasonic flaw detection equipment. The use of ultrasonic flaw detection equipment can raise time and efficiency issues. In order to solve this problem, we will study the basic technology necessary for the development of automated inspection system equipped with ultrasonic measuring equipment and verify the validity through the fabrication of the demonstration device.