• Applied Biological Chemistry
• /
• v.48 no.4
• /
• pp.388-393
• /
• 2005

This study was conducted to experiment the removal efficiency of 6 pesticides in fruits and vegetables using various washing solutions. As results, the average removal efficiencies of pesticides washed with tap-water were 68.3%, whereas those washed by ultrasonic cleaning for 2 and 5 minutes were 73.7% and 82.5%, respectively. Using different washing solutions with various additional materials such as 0.5% detergent, 5% vinegar, 5% salt and flour, the removal rates were 82.9%, 76.9%, 75.8% and 75.7%, respectively. With 0.5% detergent, pesticides were 20% more removed when washed by ultrasonic cleaning than tap-water washing; moreover, Chlorthalonil in cherry tomato showed the highest removal efficiency while EPN in grape washed with tap-water showed the lowest. The order of removal efficiencies of pesticides were Chlorthalonil (90.0%)>Procymidone (81.3%)>Chlorpyrifos (76.6 %)>Endosulfan (75.7%)>Fenitrothion (75.5%)>EPN (73.8%).

• Journal of Applied Biological Chemistry
• /
• v.63 no.1
• /
• pp.51-60
• /
• 2020

This study was conducted to investigate changes in pesticide residues in eggplant and lettuce during washing and cooking processes after application with azoxystrobin. Eggplant was processed with running washing, steaming, and stir-frying, and lettuce was processed with soaking washing, running washing, soaking and running washing, ultrasonic cleaning, and blanching. The limit of quantitation of GC analysis of azoxystrobin was 0.01 mg/kg and the recovery rate was 84.7-109.5%. The azoxystrobin processing factors (PFs) and reduction rates in eggplant and lettuce were calculated and the results were as follows. In the case of eggplant, the azoxystrobin PF and reduction rate of running washing were 0.29 and 71.1%, respectively, those of steaming were 0.32 and 68.0%, respectively, and those of stir-frying were 0.24 and 75.7%, respectively. In the case of lettuce, the azoxystrobin PF and reduction rate of soaking washing were 0.25, 75.3%, those of running washing were 0.61 and 38.9%, respectively, those of soaking and running washing were 0.32, 68.0%, those of ultrasonic cleaning were 0.47 and 53.1%, respectively, and those of blanching were 0.26 and 73.6%, respectively. It could be identified that pesticide residues in eggplant and lettuce can be effectively reduced through washing and cooking processes and that most of pesticide residues were removed when cooking processes were undergone after washing. Therefore, azoxystrobin PFs after washing and processing can be provided as basic data for risk assessment.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.2
• /
• pp.207-215
• /
• 2006

This study evaluated the effect of ultrasonic irradiation on reducing membrane fouling for the treatment of chemically treated leachate and biologically treated leachate. The experiments on improvement of membrane flux according to the membrane types(MF and UF) and membrane materials were performed with changing frequency(40 kHz and 120 kHz) and intensity(200 W and 400 W) of ultrasound in ultrasonic membrane separation apparatus which ultrasound can be periodically irradiated. Additionally, the effect of dual frequency ultrasound which 40 kHz md 120 kHz are irradiated simultaneously was evaluated. The improvement of membrane flux by periodical ultrasound irradiation was higher in microfiltration(MF) membrane than in ultrafiltration(UF) membrane. It was sustained more in the MF membrane of polyvinylidene fluoride(PVDF) than in that of polysulfon(PS). Ultrasonic improvement of membrane flux was different depending on the characteristics of target wastewater. It was sustainably maintained without reclogging using dual frequency ultrasound although the improvement of membrane flux was lower.

• Applied Chemistry for Engineering
• /
• v.5 no.2
• /
• pp.199-208
• /
• 1994

In this study, the ultrasound which provides the properties of mixing, and surface cleaning effect, the increase of the effective reaction surface area and the enhancement of the effective collision frequency, was used to enhance the recovering efficiency of Cu from the Cu-ion containning waste water. The ultrasonic reactor used in this study was designed and constructed for improving the disadvantage of the existing ultrasonic reactor. From the experimental result and its analysis, we obtained following conclusions. 1. The ultrasound increased the rate of electrochemical deposition to 582.2% in maximum at the condition of $0.1M-CuSO_4$, and 2.1 V-overpotential. 2. The enhancement effect of ultrasound induced by the reduction of diffusion layer thickness was 277.8% in maximum and induced by the other effect except for the reduction effect of the diffusion layer thickness was 253.6% in maximum at $0.1M-CuSO_4$ and 2.1V overpotential. 3. This study gave the possibility of the scale-up of ultrasonic reactor and in particular, ultrasonic reactor would be effective in the treatment of waste water containning a low concentration of Cu ion.

• Resources Recycling
• /
• v.30 no.5
• /
• pp.38-48
• /
• 2021

In this study, we determine the optimal process conditions for selectively recovering Si from a solar cell surface by removal of impurities (Al, Zn, Ag, etc.). To selectively recover Si from solar cells, leaching is performed using HCl solution and an ultrasonic cleaner. After leaching, the solar cells are washed using distilled water and dried in an oven. Decompression filtration is performed on the HCl solution, and ICP-OES (Inductively Coupled Plasma Optical Emission spectroscopy) full scan analysis is performed on the filtered solution. Furthermore, XRD (X-ray powder diffraction), XRF (X-ray fluorescence), and ICP-OES are performed on the dried solar cells after crushing, and the purity and recovery rate of Si are obtained. In this experiment, the concentration of acid solution, reaction temperature, reaction time, and ultrasonic intensity are considered as variables. The results show that the optimal process conditions for the selective recovery of Si from the solar cells are as follows: the concentration of acid solution = 3 M HCl, reaction temperature = 60℃, reaction time = 120 min, and ultrasonic intensity = 150 W. Further, the Si purity and recovery rate are 99.85 and 99.24%, respectively.

• Journal of the Korean Society of Safety
• /
• v.29 no.4
• /
• pp.123-131
• /
• 2014

Whole amount of waste water, approximately 921.6 liter, for cleaning a ready mixed concrete truck should be used to produce concrete as a mixing water or cleaning water. Recycling water for concrete mixing contains solids, which cause decrease in slump, air and compressive strengths, so it may influence on poor concrete quality. Therefore, it has been maintained to use recycling water with less than 3 percent of solids. Since no evaluation system has been constructed to directly reflect on variability of recycling water from ready mixed concrete plants, it is necessary to develop "Automatic recycling solid measuring system" for quality controls in real time. In this research, sensors measuring waste water concentration in ultrasonic and inductance methods were developed, and automatic system using the sensors were established. The accuracy of measurement sensors developed for recycling water based on various conditions of concentration was proved, and application limits were evaluated. Also, concentration of recycling water using sensors developed from ready mixed concrete plant was measured, and curing method verified the accuracy of the sensors. Moreover, measurement sensors for recycling water in various locations were installed to evaluate the effects on measuring method and spots. The automatic measuring system for recycling water concentration, which is developed in the research, will contribute to improve concrete quality safety through reliable solids maintenance.

• Korean Journal of Materials Research
• /
• v.27 no.6
• /
• pp.325-330
• /
• 2017

Photoelectron-hole separation efficiency plays an important role in the enhancement of the photocatalytic activity of photocatalysts towards the degradation of organic molecules. In this study, $TiO_2/TiOF_2$ heterostructured composite powders with suitable band structures, which structures are able to separate photoelectron-hole pairs, have been synthesized using a simple and versatile ultrasonic spray pyrolysis process. In addition, their phase volume fractions have been controlled by varying the pyrolysis temperature from $400^{\circ}C$ to $800^{\circ}C$. The structural and optical properties of the synthesized powders have been characterized by X-ray diffraction, scanning electronic microscopy and UV-vis spectroscopy. The powder with a phase volume ratio close to 1, compared with single $TiOF_2$ and other composite powders with different phase volume fractions, was found to have superior photocatalytic activity for the degradation of rhodamine B. This result shows that the $TiO_2/TiOF_2$ heterostructure promotes the separation of the photoinduced electrons and holes and that this powder can be applicable to environmental cleaning applications.

• Restorative Dentistry and Endodontics
• /
• v.46 no.1
• /
• pp.11.1-11.11
• /
• 2021

Objectives: The aim of this study was to compare smear layer removal by conventional application (CA), passive ultrasonic irrigation (PUI), EasyClean (EC), and XP-Endo Finisher (XPF), using 17% ethylenediaminetetraacetic acid (EDTA) after chemomechanical preparation, as evaluated with scanning electron microscopy (SEM). Materials and Methods: Forty-five single-rooted human mandibular premolars were selected for this study. After chemomechanical preparation, the teeth were randomly divided into 5 groups according to the protocol for smear layer removal, as follows: G1 (control): CA of distilled water; G2 (CA): CA of 17% EDTA; G3 (PUI): 17% EDTA activated by PUI; G4 (EC): 17% EDTA activated by EC; and G5 (XPF): 17% EDTA activated by XPF. SEM images (×1,000) were obtained from each root third and scored by 3 examiners. Data were evaluated using the Kruskal-Wallis and Dunn tests (p < 0.05). Results: In the apical third, there were no statistically significant differences among the groups (p > 0.05). In the cervical and middle thirds, the experimental groups performed better than the control group (p < 0.05); however, G2 presented better results than G3, G4, and G5 (p < 0.05), which showed no differences among one another (p > 0.05). Conclusions: No irrigation method was able to completely remove the smear layer, especially in the apical third. Using CA for the chelating solution performed better than any form of activation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.500-500
• /
• 2013

특정한 유기 물질에 전류를 인가했을 때 발광을 하는 특성을 이용한 Organic Light Emitting Diode (OLED)는 뛰어난 색재현성, 적은 전력소모, 간단한 제조공정, 넓은 시야각 등으로 인해 PDP, LCD, LED에 이은 차세대 디스플레이 소자로 많은 관심을 받고 있다. 하지만 OLED는 각기 다른 굴절률을 가지는 다층구조로 되어있어 실질적으로 소자 밖으로 나오는 빛은 원래 생성된 빛의 20% 정도 밖에 되지 않는다. 이러한 광 손실을 줄이기 위해 Photonic Crystal (PC)이나 마이크로 렌즈 어레이(MLA) 부착 등과 같이 특정한 크기를 갖는 주기적인 나노 구조물을 이용한 광추출 효율 상승 방법은 특정 파장의 빛에서만 효과가 있는 한계가 있었으며 고가의 공정과정을 거쳐야 했으므로 OLED 소자의 가격 향상에 일조하였다. 이의 해결을 위해 본 연구는 유리기판 위에 랜덤한 분포를 가지는 나노 구조물 제작 공정법을 제안한다. 먼저 유리기판 위에 스퍼터로 금속 박막을 입혀 이를 Rapid thermal annealing (RTA) 공정을 이용하여 랜덤한 분포의 Island를 가지는 마스크를 제작하였다. 그 후 플라즈마 식각을 이용하여 유리기판에 나노 구조물을 형성하였고 기판 위에 남아있는 마스크는 Ultrasonic cleaning을 이용하여 제거하였다. 제작된나노구조물은 200~300 nm의 높이와 약 200 nm 폭을 가지고 있다. 제작된 유리기판의 OLED 소자로의 적용가능성을 알아보기 위한 광학특성 조사결과는 300~900 nm의 파장영역에서 맨유리와 거의 비슷한 수직 투과율을 보이면서 최대 50%정도의 Diffusion 비율을 나타내고 있고 임계각(41도) 이상의각도에서 인가된 빛의 투과율에 대해서도 향상된 결과를 보여주고 있다. 제안된 공정의 전체과정 기존의 PC, MLA 등의 공정에 비해 난이도가 쉽고 저가로 진행이 가능하며 추후 OLED 소자에 적용될 시 대량생산에 적합한 후보로 보고 있다.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.4 s.193
• /
• pp.153-158
• /
• 2007

Recently nano imprint lithography to fabricate photonic crystal on polymer is preferred because of its simplicity and short process time and ease of precise manufacturing. But, the technique requires the precise mold as an imprinting tool for good replication. These molds are made of the silicon, nickel and quartz. But this is not desirable due to complex fabrication process, high cost. So, we describe a simple, precise and low cost method of fabricating PDMS stamp to make the photonic crystals. In order to fabricate the PDMS mold, we make the original pattern with designed hole array by finding the optimal electron beam writing condition. And then, we have tried to fabricate PDMS mold by the replica molding with ultrasonic vibration and pressure system. We have used the cleaning process to solve the detaching problem on the interface. Using these methods, we acquired the PDMS mold for photonic crystals with characteristics of a good replication. And the accuracy of replication shows below 1% in 440nm at diameter and in 610nm at lattice constant by dimensional analysis by SEM and AFM.