• 동력기계공학회지
• /
• 제14권3호
• /
• pp.58-63
• /
• 2010

A laser beam welding and an electric arc welding were combined, and the positive points of each welding method are drawn such as high speed, low thermal load, deep penetration, and high productivity. The fiber laser-MIG conjugated welding. namely the hybrid welding has been studied mainly for the automation industry of a pipeline welding. In this study, the MIG welding was combined with a fiber laser welding to make up the hybrid welding. The weld shapes, microstructures and mechanical properties for weld zones after the hybrid welding or only fiber laser welding were investigated on the 700 MPa grade Ultra Fine Grained(UFG) high strength steel. The amount of acicular ferrite in weld metals and HAZ(heat affected zone) was observed larger after hybrid welding compared with after only laser welding. The Vickers hardness of the top area of the fusion zone after fiber laser welding was higher compared with after hybrid welding.

• 플랜트 저널
• /
• 제6권3호
• /
• pp.53-61
• /
• 2010

This paper presents failure analysis on weld-joint of the waterwall tubes in USC boilers. Visual inspections were performed to find out the characteristics of the fracture. Additionally both microscopic characteristics and hardness test were carried out on failed tube samples. Failures seem to happen mainly because the welding process such as preheating and PWHT(post-weld heat treatment) was not conducted strictly. Thus, this paper has the purpose to describe the main cause of the poor welding process and to explain how to prevent similar failures in those weld-joints.

• Journal of Power Electronics
• /
• 제6권2호
• /
• pp.139-145
• /
• 2006

This paper describes the ultra precise position estimation of a servomotor using a sinusoidal encoder based on Arcsine Interpolation Method for the cost reduction of circuit design. The amplitude and offset errors of the sinusoidal encoder output signals, from the encoder itself and analog signal processing procedures, are effectively compensated and on-line tuned by utilizing a low cost programmable differential amplifier without any special expensive equipment. For a theoretical evaluation of the practical resolution of this system, the relationship between the amplitude of ADC(Analog to Digital Converter) input signal errors and the anticipated resolution is also addressed. The performance of the proposed method is verified by comparing it with speed control characteristics of the servomotor driving system using a digital incremental 50,000ppr encoder in the experiments.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 I
• /
• pp.446-449
• /
• 2003

In recent years, the research of an efficient transmission method is going to meet a demand for high speed and large capacity radio communication. These systems make use of ultra-short duration pulses which yield UWB(Ultra Wide Band) signals characterized by low power spectral densities. The wavelet synthesis wave is able to set up the scale freely. So it is possible to use as the transmission wave of UWB by compressing time. In this paper, we present a general analytical expression for the average BER(Bit Error Rate) performance of UWB data transmission using wavelet system as a function of the cross-correlation between the users' signatures in an additive white Gaussian noise(AWGN) channel.

• Journal of Communications and Networks
• /
• 제6권2호
• /
• pp.163-172
• /
• 2004

Ultra Wide Bandwidth (UWB) spread-spectrum techniques will playa key role in short range wireless connectivity supporting high bit rates availability and low power consumption. UWB can be used in the design of wireless local and personal area networks providing advanced integrated multimedia services to nomadic users within hot-spot areas. Thus the assessment of the possible interference caused by UWB devices on already existing narrowband and wideband systems is fundamental to ensure nonconflicting coexistence and, therefore, to guarantee acceptance of UWB technology worldwide. In this paper, we study the coexistence issues between an indoor UWB-based system (hot-spot) and outdoor point to point (PP) links and Fixed Wireless Access (FWA) systems operating in the 3.5 - 5.0 GHz frequency range. We consider a realistic UWB master/slave system architecture and we show through computer simulation, that in all practical cases UWB system can coexist with PP and FWA without causing any dangerous interference.

• 한국항행학회논문지
• /
• 제9권1호
• /
• pp.1-8
• /
• 2005

본 논문에서는 차세대 근거리 실내 무선 환경 기술로 채택 가능성이 높은 UWB(Ultra Wideband)기술용 Impulse Generator를 SRD(Step Recovery Diode)를 이용하여 설계하였다. 설계 목표는 단순한 설계 구조와 함께 저가, 소형, 고성능의 Impulse Generator 개발에 있다. 미국의 FCC(Federal Communications Commission)의 기준인 주파수 범위 3.1~10.6 GHz, 출력 제한 레벨 -41.25 dBm을 만족하는 Impulse Generator를 회로 시뮬레이터인 Agilent Technologies사의 ADS를 이용하여 설계, 제작, 측정하였다. 설계된 회로의 출력 신호는 단일밴드용과 멀티밴드용으로 구분하였다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권6호
• /
• pp.286-292
• /
• 2005

Terahertz wave is a kind of electromagnetic radiation whose frequency lies in 0.1THz $\~$10THz range. In this paper, generation and detection characteristics of terahertz (THz) radiation by photoconductive antenna (PCA) method has been described. Using modern integrated circuit techniques, micron-sized dipole antenna has been fabricated on a low-temperature grown GaAs (LT-GaAs) wafer. A mode-locked Ti:Sapphire femtosecond laser beam is guided and focused onto photoconductive antennas (emitter and detector) to generate and measure THz pulses. Ultra-wide band THz radiation with frequencies between 0.1 THz and 3 THz was observed. Terahertz field amplitude variation with antenna bias voltage, pump laser power, pump laser wavelength and probe laser power was investigated. As a primary application example. a live clover leaf was imaged with the terahertz radiation.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.19-19
• /
• 2009

Recently, Light Emitting Diode(LED) has many advantages in comparison with conventional light sources; low power consumption, long lifetime, and less environmental pollution. Therefore, the use of LED is multiplying and increasing rapidly. In general, however, spherical lens is used in LED-lighting which cause many problems induces by optical aberration of spherical lens; low illumination, a yellow belt, unpleasant feeling in human eye. As a potential solution of this problem, aspherical lens can be employed. This study reports the improvement of LED-lighting performance by adopting aspherical lens. From the commercial program, $LightTools^{TM}$, the optical problem were ensured. And then, to improve this problem, optimum aspheric form was designed using Code $V^{TM}$.

• International Journal of Internet, Broadcasting and Communication
• /
• 제13권1호
• /
• pp.69-81
• /
• 2021

While the fifth generation (5G) and beyond 5G (B5G) mobile communication networks are being rolled over the globe, several world-wide companies have already started to prepare the sixth generation (6G). Such 6G mobile networks targets ultra-reliable low-latency communication (URLLC). In this paper, we challenge to reduce the inherent latency of existing non-orthogonal multiple access (NOMA) in 5G networks of massive connectivity. First, we propose the novel unipodal binary pulse amplitude modulation (2PAM) NOMA, especially without SIC, which greatly reduce the latency in existing NOMA. Then, the achievable data rates for the unipodal 2PAM NOMA are derived. It is shown that for unequal gain channels, the sum rate of the unipodal 2PAM NOMA is comparable to that of the standard 2PAM NOMA, whereas for equal gain channels, the sum rate of the unipodal 2PAM NOMA is superior to that of the standard 2PAM NOMA. In result, the unipodal 2PAM could be a promising modulation scheme for NOMA systems toward 6G.

• 전자통신동향분석
• /
• 제36권3호
• /
• pp.41-52
• /
• 2021

Recently, LNOI photonics technology has attracted attention as a photonics platform capable of integrating ultra-high-speed, low power consumption, and high nonlinearity optical devices, as it is possible to manufacture LiNbO₃ optical waveguides with ultra-low optical loss and a radius of curvature of several tens of micrometers. Here, we will briefly compare various photonics platforms, such as Si, InP, SiN, and LNOI, describe the current research trends of LNOI photonics, and discuss the direction of photonics technology at the conclusion.