• Journal of the Korea Society of Computer and Information
• /
• v.24 no.4
• /
• pp.11-18
• /
• 2019

Previous mutual authentication schemes operate on the basis of validated cryptographic functions and hash functions, but these functions require a certain amount of memory capacity. However, since ultra-lightweight IoT devices have a very small amount of memory capacity, these functions can not be applied. In this paper, we first propose a text steganography communication scheme suitable for ultra-lightweight IoT devices with limited resources, and then propose a mutual authentication scheme based on the text steganography communication. The proposed scheme performs mutual authentication and integrity verification using very small amount of memory. For evaluation, we implemented the proposed scheme on Arduino boards and confirmed that the proposed scheme performs well the mutual authentication and the integrity verification functions.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.05a
• /
• pp.349-350
• /
• 2012

Porous silicon (PS) was prepared by electrochemical anodization. Ultra-thin zinc oxide (ZnO) capping layers were deposited on the PS by plasma-assisted molecular beam epitaxy (PA-MBE). The effects of the ZnO capping layers on the properties of the as-prepared PS were investigated using scanning electron microscopy (SEM) and photoluminescence (PL). The as-prepared PS has circular pores over the entire surface. Its structure is similar to a sponge where the quantum confinement effect (QCE) plays a fundamental role. It was found that the dominant red emission of the porous silicon was tuned to white light emission by simple deposition of the ultra-thin ZnO capping layers. Specifically, the intensity of white light emission was observed to be enhanced by increasing the growth time from 1 to 3 min.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.389-392
• /
• 2008

Ultra-high strength concrete becomes one of the main research areas because recently concrete structure is larger. The quality of aggregate (ultra-high strength and uniformity) as well as chemical admixture and mineral additives is a key factor for ultra-high strength concrete development. However, natural aggregate including crushed aggregate is inappropriate for ultra-high strength concrete because ultra-high strength quality cannot be maintained uniformly over whole natural aggregate lot. In this study ceramic aggregate was applied for ultra-high strength concrete in order to assure uniform quality of ultra-high strength aggregate. Ultra-high strength concrete was achieved by applying coated ultra-high strength ceramic aggregate to enhance the bonding strength between aggregate and cement paste. Also for actual application light weight ceramic aggregate(density 2.2 $g/cm^3$) with zero water absorption was tested.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.125-132
• /
• 2002

Recently, ULSAB(Ultra Light Steel Auto Body) concept is getting more attention due to various benefits in automotive body design. One of the ULSAB efforts is making a door with TWB(Tailor Welded Blanks). In TWB, two or more patches of steel panels are welded together before stamping process. In this research, domains and thicknesses of the patches in a front door structure are determined by a series of optimization schemes composed of topology, size and shape optimization and DOE(Design of Experiments) scheme. A door is designed to have better performances compared to exiting structure considering static stiffness and natural frequency. The final design is discussed and compared to the existing design.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.483-486
• /
• 2004

Inner structured and bonded panel, or ISB Panel, as a kind of sandwich type panel, has metallic inner structures which have low relative density, because of their dimensional shape of metal between a pare of metal skin sheets or face sheets. In this work, ISB panels and inner structures formed as repeated pyramidal shapes are introduced. Pyramidal structures are formed easily with expanded metal sheet by the crimping process. Three kinds of pyramidal structures are made and used to fabricate test specimen. Through the multi-point electrical resistance welding, inner structures are bonded with skin sheet. 3-point bending tests are carried out to measure the bending stiffness of ISB panel and experimental results are discussed.

• Journal of the Korean Society of Safety
• /
• v.26 no.2
• /
• pp.1-5
• /
• 2011

In order to evaluate fatigue endurance for an ultra-light weight inline skate frame, FEM analysis was performed. Tensile properties and a S-N curve were determined through tensile and fatigue tests on a modified Al-7075+$S_c$ alloy. The yield and ultimate tensile strengths were 553.3 MPa and 705.5 MPa, respectively. The fatigue endurance limit of this alloy was 201.2 MPa. For evaluating the fatigue endurance of the inline skate frame, the S-N data were compared with the stress analysis results through FEM analysis of the frame. The maximum Von-Mises stress of the frame was determined 106 MPa through FEM analysis of the frame, assuming that the rider weight is 75 Kg. Conclusively, on the basis of fatigue limit, the inline skate frame has a safety factor of approximately 2.0.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.67-68
• /
• 2006

In this paper, a new revolute cooperating robot arms with 12 d.o.f was developed for autonomous moving robots. The robot ann was designed to have the load capacity of 10 Kg. For this, a new joint actuator based on the fourbar link mechanism was employed. As a control system for the robot arm, a distributed control system was developed composed of the main controller and five motor controller for the ann joints. The main controller and the motor controller were developed using the ARM microprocessor and the TMS320c2407 processor, respectively. To validate the performance of the robot system, an experiment to support 10 Kg payload was performed.

• Journal of the Korean Applied Science and Technology
• /
• v.20 no.2
• /
• pp.177-181
• /
• 2003

Ultra-thin films of amphiphillic squarylium dye were prepared on the hydrophillic substrate by Langmuir-Blodgett(LB) technique. In this study, the photoelectric properties of a amphiphillic squarylium dye LB film was investigated. The visible light(${\lambda}$ = 684nm ) of xenon lamp was illuminated on the amphiphillic squarylium dye LB films and light absorptivity and photoconductivity were observed. The photoconductivity was nearly constant regardless of nominal layer number. The photoelectric properties of the amphiphillic squarylium dye LB films with bottom electrode showed better than that top electrode.

• Journal of the Korean Ceramic Society
• /
• v.37 no.1
• /
• pp.82-89
• /
• 2000

In lithium silicate photosensitive glass-ceramics, the relationship between lithography time and crystallization, and the effect of addition of mineral acid in etching rate and pattern shape were investigated. Irradiation times for micropatterning were less than 5 minutes in which Ce3+ ions in glass were changed rapidly to Ce4+ with ultra violet light. Overexposure to ultra brought about blot of pattern by diffiraction of light. Addition of mineral acid to HF enhanced etching rate as compared with HF solution only. The addition of H2SO4 especially increased the etching rate by 70%. But the mixed solution also increased the etching rate of the noncrystallized portion of the glass and this resulted in heavy etching. Etching with ultrasonic wave showed higher etching rate than that with the static or fluid method.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.9 s.252
• /
• pp.1078-1085
• /
• 2006

Many studies have been focused on how to manufacture ultra light metal structures and optimize them. In this study, we introduced a new idea to make sandwich panels with quasi-Kagome truss cores. First, metal sheets with a peculiar pattern of slits were expanded to be meshes, they are crimped into a triangular wave pattern, and then one third of struts were bent reversely to be quasi-Kagome trusses. Finally, two face sheets were bonded on the upper and the lower sides. The bending strength was estimated through elementary mechanics for the sandwich specimens with two kinds of face sheet the results of estimation were compared with the those of finite element analyses and experiments.