• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.37 no.5
• /
• pp.28-35
• /
• 2000

In this paper, we design a ring inductor using the ferrite core to denoise the EMI(Electromagnetic Interference) for facsimile. The EMI for facsimile is radiated from the signal line of PSTN(Public Switching Telephone Network) between facsimile and PSTN. We denoise the radiated noise by inserting a ferrite core(Ni-Zn) between facsimile and PSTN. Even though we may denoise the radiated noise using two or more than two ferrite cores, we only concentrate on denoising EMI by adjusting number of turns of one ferrite core since it gives economical gain. As a result of measuring EMI using the designed inductor with 4 turns inserted in the line connected between facsimile and PSTN, the value of radiated emission is reduced below 30 dB$\mu$V/m.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.9
• /
• pp.661-667
• /
• 2018

Tactical communication radio systems that employ software defined radios(SDRs) have been developed for achieving high-speed data transmissions and voice communications. Such systems possess multiband and multichannel features, and can potentially replace several existing radio systems. This paper proposes a design for wideband antennas by incorporating a diplexer matching network for tactical vehicles. The proposed antenna design includes two radiators(upper and lower) and a diplexer matching network connected to the end of the feed line such that the LC matching networks are interleaved in the lower radiator and spring mount. By employing the diplexer matching network, the designed antenna can perform wideband impedance matching for the fifty ohm feed line. The designed LC networks aid in varying the effective electrical length of the antenna according to the operation frequency. The primary objective behind adjusting the electrical length is to vary the current distribution above and below the LC networks. The proposed antenna was fabricated and tested in an open site. The obtained evaluation results show that the designed antenna can achieve a relative bandwidth of 190% with a VSWR value of 3.5:1, and can attain good antenna gains over VHF and UHF bands.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.6
• /
• pp.809-814
• /
• 2011

The major resource problem in sensor networks is energy efficiency. There are two major access methods to efficiently use energy. The first is to use dynamic power management (DPM). The second is to use energy efficient protocols. In DPM methods, the OS, the power manager, is responsible for managing the proper power state of CPU and each I/O with respect to the events, but the OS is not largely concerned about the internal operation of each network protocols. Also, energy efficient protocols are mainly focused on the power saving operation of the radio PHY. In addition, in wireless sensor network most of tasks are connected to communication. In such a situation, traditional power managers can waste unpredicted power. In this paper, we introduce an efficient power manger that can reduce a lot of unwanted power consumption through cooperative power management (CPM) in communication-related tasks between each units, such as radio, sensing unit, and CPU, for ad hoc wireless sensor nodes.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.9
• /
• pp.814-820
• /
• 2015

In this paper, A high selective dual-band bandpass filter was proposed using a dual-mode ring resonator with two short-circuited stubs. For dual-mode resonance, the ring resonator is directly connected with non-orthogonal feed-lines via coupling capacitors. Two short-circuited stubs which are unequal lengths are simultaneously placed at two corners along the two symmetry plane of the ring resonator in order to obtain dual-band responses. Because the feeding angle perturbated ring resonator of the proposed dual-band bandpass filter has the symmetrical structure, Even/Odd mode analysis can be well applied to extract the scattering parameters and transmission zero frequencies. The proposed dual-band bandpass filter was designed and fabricated for WLAN(Wireless Local Area Network) application of IEEE 802.11n standard. The measured results showed a good agreement with the simulation results, and it should be well applied not only for WLAN applications but also for any other communication systems.

• Journal of KIISE:Computing Practices and Letters
• /
• v.5 no.6
• /
• pp.782-792
• /
• 1999

효과적인 ATM 망의 관리는 연결 지향 환경, 다양한 서비스 등급, 대규모 트래픽, 가상 망 구성 그리고 여러가지 트래픽 유형 등과 같은 다양한 ATM 특성을 다룰 수 있어야만 한다. 이를 위해 ATM 포럼에서는 ATM 장치, 사설망, 공중망 및 그들간의 상호작용을 지원하기 위한 ATM 망 관리 참조 모델을 정의하였으며, 그 중 하나가 서로 다른 판매자로부터의 ATM 장비들간의 상호동작성을 보장하기 위해 SNMP 기반 망 관리 프로토콜을 통해 상호 연결된 인터페이스를 관리할 수 있도록 정의된 통합 지역 관리 인터페이스(ILMI) 프로토콜이다. ILMI의 목적은 두 인접한 ATM 장치로 하여금 그들 간에 공통의 ATM 링크에 대한 동작 파라메타를 자동적으로 구성할 수 있도록 함으로서, 관리자에 의해 수동 구성이 아닌 ATM 장치 상호간의 플러그 앤 플러그 기능을 지원하는데 있다. 본 논문에서는 이러한 ILMI 기술을 바탕으로 공중망 ATM 교환기에 연결된 가입자의 물리 인터페이스, ATM 계층 인터페이스, VPC 및 VCC의 구성 및 상태 정보를 효율적으로 관리하며, 가입자 시스템의 ATM 주소를 자동으로 등록, 관리할 수 있도록 하는 가입자 인터페이스 관리 시스템(SIMS)을 설계하고, 구현하였다. Abstract An effective ATM management must address the various features of ATM such as connection-oriented environment, varying class of service, large scale traffic, virtual network configurations and, and multiple traffic types. For this, ATM network management reference model defined by ATM Forum describes the various types of network management needed to support ATM devices, private networks, public networks, and the interaction between them. One of these types is Integrated Local Management Interface (ILMI) defined to manage interconnected interface through SNMP-based network management protocol for ensuring the interoperability of ATM devices from different vendors. The purpose of ILMI is to enable two adjacent ATM devices to automatically configure the operation parameters of the common ATM link between them and then to provide a Plug and Plug function to any ATM devices with not a passive configuration by manager but a automatic configuration. This paper design and implement a Subscriber Interface Management System (SIMS) which provide automatic registration and management of ATM address of subscriber system and efficiently manages physical interface of subscriber who is connected to public ATM switch, ATM layer interface, configuration information and status information of VPC and VCC.

• Smart Media Journal
• /
• v.4 no.2
• /
• pp.46-54
• /
• 2015

Communication between ECUs (Electronic Control Units) in agricultural machineries tends to use IS011783 widely, that is PGN (Parameter Group Number) based communication protocol lays on CAN protocol by altering its identifier part. Messages in line are transferred and received between ECUs according to ISO11783 standard. This paper discusses about design of wireless monitoring system. We used an ARM Cortex-M3 microcontroller embedded development board and marvel8686 wireless module. The wireless ISOBUS monitoring system, attached to communication line, reads messages, interpret them, and display them on the screen in easily comprehendible form. It can be used to generate messages and monitor the traffic on physical bus systems. The monitoring system connected to ECUs, monitor and simulate real traffic of communication and functionality of the ECUs. In order to support our work, we have implemented the monitoring tool. The development consists of two parts: GUI of the application and firmware level programming. Hence the monitoring system is attached to the communication line and equipped by Wi-Fi module; farmer/dispatcher in a farm monitors all messages in communication line on personal computer and smart device.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.5 no.1
• /
• pp.111-115
• /
• 2011

In this paper, we present a novel time-synchronization method for distributed systems to measure the body motion. The distributed system scheme is considered because human data acquisition systems tend to have a centralized controller with sensors connected with a long range of electric wires running through the subject's body, which results in inconvenience. Utilizing simple key switches and digital input ports for reading the key, the proposed method requires a very simple hardware structure, which means less power consumption compared with the well-known ubiquitous sensor network. After measuring the motion data as well as the synchronization pulses, the proposed method compensates, in offline, the difference of the sampling instance between the two systems by scaling the time difference. The paper presents experimental results to show the validity of the proposed method.

• ETRI Journal
• /
• v.19 no.3
• /
• pp.141-168
• /
• 1997

The base station (BS) in the CDMA Mobile System (CMS) connects calls through the radio interface and is designed to provide mobile subscribers with high quality service in spite of mobile subscribers motions. The BS consists of multiple base station transceiver subsystems (BTSs), a base station controller (BSC) and a base station manager (BSM). This paper is concerned with the BSC and the BSM. The BSC is located between the BTSs and the mobile switching center (MSC) connected with the public network, and to mobile subscribers via the BTSs. The BSM provides operator-interfaces per the BS and takes responsibility of operation and maintenance (OAM) of the BS. Design of the BSC is based on two module types: functional module and unit module. The functional module is used to support new services easily and the unit module to increase the system capacity economically. Both modular types are easily achieved by inserting the corresponding modules to the system. Particularly, in order to efficiently support the soft handover which is one of CDMA superior advantages, the BSC adopts a large high-speed Packet switch connecting up to 512 BTSs, and thus mobile subscribers can be provided with soft handover in high probability. The BSM is based on a commercial workstation to support OAM functions efficiently and guarantee high reliability of the functions. The BSM uses graphical user interface (GUI) for efficient OAM functions of the BS.

• Journal of IKEEE
• /
• v.16 no.3
• /
• pp.217-223
• /
• 2012

This paper presents design and operational characteristics of 150 MW pulse power system for high current pulse forming network to control trigger time. The system is composed of two capacitor bank modules. Each capacitor bank module consist of a trigger vacuum switch, 9k 33kJ capacitor, an energy dump circuit, a crowbar circuit and a pulse shaping inductor and is connected in parallel. It is controlled by trigger controller to select operational module and determine triggering time. Pspice simulation was conducted about determining parameters of components such as crowbar circuit, capacitor, pulse forming inductor, trigger vacuum switch and predicting results of experiment circuit. The result of the experiment was in good agreement with the result of the simulation. The various current shapes with 300~650 us pulse width is formed by sequential firing time control of capacitor bank module. The maximum current is about 40 kA during simultaneous triggering of two capacitor bank modules. The developed 150 MW pulse power system can be applied to high current pulse power system such as rock fragmentation power sources, Rail gun, Coil gun, nano-powers, high power microwave.

• The KIPS Transactions:PartC
• /
• v.14C no.6
• /
• pp.537-544
• /
• 2007

A home network is a residential local area network in which digital home appliances are connected with each other. Applying the mobile agent technology to the home network is expected to provide a new computing model. In particular, mobility and asynchronous ability of mobile agent can be used to reduce network traffic generated for managing home appliances. However, in order to apply the mobile agent concept to the home network, access control for mobile agents is necessary. In the existing home network system, there is one special server, sometimes called home server This server generally has mapping tables to be updated periodically, which describes access control lists between users' authorities and corresponding devices. In this paper, we propose a role-based access control framework with mobile agents in home networks. This framework, called Secure KAgent framework, is designed and implemented based on KAgent system. It has two main characteristics: to control access permissions based on Role-Based Access Control(RBAC) scheme and to safety assign roles to mobile agents by role tickets.