• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.26 no.12
• /
• pp.605-619
• /
• 2014

This article reviews the papers published in the Korean Journal of Air-Conditioning and Refrigeration Engineering during 2013. It is intended to understand the status of current research in the areas of heating, cooling, ventilation, sanitation, and indoor environments of buildings and plant facilities. Conclusions are as follows. (1) The research works on the thermal and fluid engineering have been reviewed as groups of fluid machinery, pipes and relative parts including orifices, dampers and ducts, fuel cells and power plants, cooling and air-conditioning, heat and mass transfer, two phase flow, and the flow around buildings and structures. Research issues dealing with home appliances, flows around buildings, nuclear power plant, and manufacturing processes are newly added in thermal and fluid engineering research area. (2) Research works on heat transfer area have been reviewed in the categories of heat transfer characteristics, pool boiling and condensing heat transfer and industrial heat exchangers. Researches on heat transfer characteristics included the results for general analytical model for desiccant wheels, the effects of water absorption on the thermal conductivity of insulation materials, thermal properties of Octadecane/xGnP shape-stabilized phase change materials and $CO_2$ and $CO_2$-Hydrate mixture, effect of ground source heat pump system, the heat flux meter location for the performance test of a refrigerator vacuum insulation panel, a parallel flow evaporator for a heat pump dryer, the condensation risk assessment of vacuum multi-layer glass and triple glass, optimization of a forced convection type PCM refrigeration module, surface temperature sensor using fluorescent nanoporous thin film. In the area of pool boiling and condensing heat transfer, researches on ammonia inside horizontal smooth small tube, R1234yf on various enhanced surfaces, HFC32/HFC152a on a plain surface, spray cooling up to critical heat flux on a low-fin enhanced surface were actively carried out. In the area of industrial heat exchangers, researches on a fin tube type adsorber, the mass-transfer kinetics of a fin-tube-type adsorption bed, fin-and-tube heat exchangers having sine wave fins and oval tubes, louvered fin heat exchanger were performed. (3) In the field of refrigeration, studies are categorized into three groups namely refrigeration cycle, refrigerant and modeling and control. In the category of refrigeration cycle, studies were focused on the enhancement or optimization of experimental or commercial systems including a R410a VRF(Various Refrigerant Flow) heat pump, a R134a 2-stage screw heat pump and a R134a double-heat source automotive air-conditioner system. In the category of refrigerant, studies were carried out for the application of alternative refrigerants or refrigeration technologies including $CO_2$ water heaters, a R1234yf automotive air-conditioner, a R436b water cooler and a thermoelectric refrigerator. In the category of modeling and control, theoretical and experimental studies were carried out to predict the performance of various thermal and control systems including the long-term energy analysis of a geo-thermal heat pump system coupled to cast-in-place energy piles, the dynamic simulation of a water heater-coupled hybrid heat pump and the numerical simulation of an integral optimum regulating controller for a system heat pump. (4) In building mechanical system research fields, twenty one studies were conducted to achieve effective design of the mechanical systems, and also to maximize the energy efficiency of buildings. The topics of the studies included heating and cooling, HVAC system, ventilation, and renewable energies in the buildings. Proposed designs, performance tests using numerical methods and experiments provide useful information and key data which can improve the energy efficiency of the buildings. (5) The field of architectural environment is mostly focused on indoor environment and building energy. The main researches of indoor environment are related to infiltration, ventilation, leak flow and airtightness performance in residential building. The subjects of building energy are worked on energy saving, operation method and optimum operation of building energy systems. The remained studies are related to the special facility such as cleanroom, internet data center and biosafety laboratory. water supply and drain system, defining standard input variables of BIM (Building Information Modeling) for facility management system, estimating capability and providing operation guidelines of subway station as shelter for refuge and evaluation of pollutant emissions from furniture-like products.

• 대한공업교육학회지
• /
• v.44 no.2
• /
• pp.104-122
• /
• 2019

In the era of the fourth industrial revolution, maker education is drawing attention as a method of student-led education. At a time when interest in maker education is also growing in technology education, figuring out what stage of concern(SoC) a middle school technology teacher is critical to effective implementation. This study analyzed SoC in maker education by layer sampling among 400 middle school technology teachers using Concerns-based adoption model. SoC was then obtained by measuring the origin using the SoCQ and then presenting it as a SOCQ profile. Gender, training experience with two lower variables were analyzed using t verification, working cities, teaching experience with more than three lower variables were analyzed using one-way ANOVA. Studies showed that SoC in maker education of middle school technology teachers showed the most similar characteristics to that of non-users. The difference in concern depending on gender was that male teachers were more concerned in maker education than female teachers. The difference in concern depending on the working city was that teachers working in the township were more concerned in the maker education than teachers working in the large city, and the difference in concern depending on the teaching career was higher among teachers with middle experience than those with low and high experience. There was also a higher stage of concern in maker education than in teachers without training experience. Therefore, it is necessary to provide middle school technology teachers with an introduction to the maker education and various information, teaching, learning and evaluation data to enhance overall concern and to support the use and evaluation of the maker education in the classroom by providing various teacher training and consulting on the maker education in the future. Further, through further study, we should conduct study that analyzes both Stage of Concern, Level of Use and Innovation Configuration, to put in the effort for effective settlement of maker education.

• Journal of Intelligence and Information Systems
• /
• v.20 no.3
• /
• pp.59-76
• /
• 2014

The revolution of smart media such as smart phone, smart TV and tablets has brought easiness for people to get contents and related information anywhere and anytime. The characteristics of the smart media have changed user behavior for watching the contents from passive attitude into active one. Video is a kind of multimedia resources and widely used to provide information effectively. People not only watch video contents, but also search for related information to specific objects appeared in the contents. However, people have to use extra views or devices to find the information because the existing video contents provide no information through the contents. Therefore, the interaction between user and media is becoming a major concern. The demand for direct interaction and instant information is much increasing. Digital media environment is no longer expected to serve as a one-way information service, which requires user to search manually on the internet finding information they need. To solve the current inconvenience, an interactive service is needed to provide the information exchange function between people and video contents, or between people themselves. Recently, many researchers have recognized the importance of the requirements for interactive services, but only few services provide interactive video within restricted functionality. Only cooking domain is chosen for an interactive cooking video query service in this research. Cooking is receiving lots of people attention continuously. By using smart media devices, user can easily watch a cooking video. One-way information nature of cooking video does not allow to interactively getting more information about the certain contents, although due to the characteristics of videos, cooking videos provide various information such as cooking scenes and explanation for each recipe step. Cooking video indeed attracts academic researches to study and solve several problems related to cooking. However, just few studies focused on interactive services in cooking video and they still not sufficient to provide the interaction with users. In this paper, an interactive cooking video query service system with linked data to provide the interaction functionalities to users. A linked recipe schema is used to handle the linked data. The linked data approach is applied to construct queries in systematic manner when user interacts with cooking videos. We add some classes, data properties, and relations to the linked recipe schema because the current version of the schema is not enough to serve user interaction. A web crawler extracts recipe information from allrecipes.com. All extracted recipe information is transformed into ontology instances by using developed instance generator. To provide a query function, hundreds of questions in cooking video web sites such as BBC food, Foodista, Fine cooking are investigated and analyzed. After the analysis of the investigated questions, we summary the questions into four categories by question generalization. For the question generalization, the questions are clustered in eleven questions. The proposed system provides an environment associating UI (User Interface) and UX (User Experience) that allow user to watch cooking videos while obtaining the necessary additional information using extra information layer. User can use the proposed interactive cooking video system at both PC and mobile environments because responsive web design is applied for the proposed system. In addition, the proposed system enables the interaction between user and video in various smart media devices by employing linked data to provide information matching with the current context. Two methods are used to evaluate the proposed system. First, through a questionnaire-based method, computer system usability is measured by comparing the proposed system with the existing web site. Second, the answer accuracy for user interaction is measured to inspect to-be-offered information. The experimental results show that the proposed system receives a favorable evaluation and provides accurate answers for user interaction.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.28 no.4
• /
• pp.36-48
• /
• 2010

The objectives of this study are to research and analyze the positioning of Mt. Back Hwa(白華山) and the characteristics of its neighboring cultural scenery based on the Two Seated Buddah Temple, a small Buddhist temple of Taeul in Taean and to view both landscape geographic codes and religious attractions over Mt. Back Hwa by discussing its expression and meaning for the scenery scattered or nested over this districts. The panoramic view of west shows the character of Mt. Back Hwa as a magnanimity of Buddhist Goddess of Mercy which is viewed as a view point field no less than its location as a landscape target and its singularity as a rocky mountain. The ancient castle, signal beacon post and the small Buddhist temple of Taeul to be read importantly in the old map and SinjeungDongkukyeojiseungram(新增東國輿地勝覽) form the core of place identity, and a number of carve(engrave) letters such as Eopungdae(御風臺), Youngsadae(永思臺), etc. show the prospect of this mountain and monumentality derived from place characteristics. In addition removing of Taeiljeon, a portrait scroll of Dangun, national ancestor makes possible to guess the national status hold by Mt. Back Hwa in advance and to know that it has symbiotic relationship with indigenous religion and shares with the universal locality which have been continued for a long time through a portrait scroll of Dangun enshrined in Samsunggak. More than anything else, however the Rock-carved Buddha Triad in Taean, Giant Buddha of Baekjae era enshrined in the small Buddhist temple of Taeul is not only why Mt. Back Hwa, magnanimity of Buddhist Goddess of Mercy exists but also a signifier. In spite of such a placity, the union ideas of confucianism, buddhism and doctrinism of buddhism prevailed in the Late Joseon Dynasty allows the cultural phenomenon of taoism to be read in the same weight through Ilsogae(一笑溪) and Gammodae(感慕臺) which are mountain stream and pond area respectively centered in the carve letter, 'Taeeuldongcheon(太乙洞天)' constructed in front of the small Buddhist temple of Taeul, the Baduk board type of rock carvings engraved over them and a number of traces of carve letters made by confucian scholars since the Middle of Joseon Dynasty. The reason such various cultural sceneries are mixed in Mt. Back Hwa is in the results of inheritance of religious places and fusion of sprit of the times, and the various type of cultural scenery elements scattered in Mt. Back Hwa are deemed as unique geographic code to understand the multi-layered placity and the characteristics of scenery of Mt. Back Hwa in Taean.

• The Journal of Engineering Geology
• /
• v.18 no.4
• /
• pp.471-482
• /
• 2008

This study was carried out to investigate the contamination characteristics of surface water, soil water and groundwater around and in antimony waste landfill site in Wonsung-ri, Yeonki-kun, Chungnam. The waste disposed in the study was excavated and transported to the other site in several years ago. For this study, we collected 35 water samples including groundwater, soil water and surface in the study site and also collected 2 groundwater samples from a comparison site. The data of chemical analysis of soil water samples show the antimony concentration of $48.75{\sim}74.81\;ppb$, which is much higher than groundwater in a comparison site and is highly excess than regulation level for a drinking water of some advanced countries. A relatively high antimony concentration was detected in three stream water samples nearby landfill site and two groundwater samples. Fe and Mn contents in soil water and stream water were measured as maxium 6.5 mg/L and 7.3 mg/L, respectively. Although other heavy metals of water samples in the study site are higher concentration than water sample of comparison site, their absolute levels are lower than regulation level for a drinking water. The chemical data of water samples are plotted widely from Ca - $HCO_3$ type to Ca - ($Cl +SO_4+NO_3$) type. Some groundwater show high contents of potassium and nitrate, which would come from fertilizer and sewage. Conclusively, some heavy metals including antimony have been still remained under the soil surface of the landfill site in the past. These metals have leaked out into nearby stream and groundwater system, and threaten the ecology, crops and the health of residents in this site. Therefore, the government have to prepare the strategy to prevent the diffusion of heavy metals into aquatic environment and have to process the reclamation work for contaminated site. It is also necessary to make a regulation level of the antimony concentration for a drinking water and soil environment in Korea.

• Applied Microscopy
• /
• v.15 no.2
• /
• pp.31-68
• /
• 1985

Authors are trying to unveil the ultrastructural organization of olfactory bulb, which has been summerized under light microscopic level or communicated only in some detail in different view point until now. For the critical point of view, since the phylogenetical approach will give the ultimate value in the correlative study between structural and functional bases (Brodal, 1969), the present study was carried out light and electron microscopic analyses of the structures of the neurons and synaptic organizations in olfactory bulbs from different animals in phylogenetical scale. We selected each one species from five animal classes: the house rabbit(Oryctolagus cuniculus var. domesticus [Gmelin]) from Mammalia, the domestic fowl (Gallus gallus domesticus Brisson) from Aves, the viper (Agkistrodon hylys [G.P. Pallas]) from Reptilia, a frog (Bombiana orientalis Boulenger) from Amphibia and the crussian carp (Carassius carassius [Linne]) from Pisces. For light microscopic study, samples were fixed in 10% formalin and paraffin sections were stained with hematoxylin-eosin. For the electron microscopic study, the tissues were fixed by perfusion through the heart or immersion with 1% paraform-aldehyde-glutaraldehyde mixture (phosphate buffer, pH 7.4), and final tissue block trimmed under dissecting microscope were osmicated (1% OsO4), they were embedded in Araldite or Epon 812, and ultrathin sections were made by LKB-V ultratome following the inspection of semi-thin sections stained with toluidine blue-borax solution. Ultra-thin sections contrasted with uranyl acetate and lead citrate were observed with JEM 100CX electron microscope. We have summerized our morphological analyses as follows: 1. The olfactory bulb of rabbit, viper and frog shows the eight layers of fila olfactoria, glomerular, external granular, external plexiform, mitral cell, internal plexiform, internal granular, medullary but domestic fowl shows the five layers of glomerular, fibrillar, mitral, granular and medullary and the three layers of fibrilla, glomerular and medullary in crussian carp. The sharpness of demarcation between the layers shows deferential tendency according to phylogenetical order. 2. Mitral cells of vertebrate have large triangular or oval shape with spherical nuclei which contain not so much chromatin. The cytoplasm contains numerous cell organelles, of which Nissl's bodies or granular endoplasmic reticula arranged as parallel strands. Development of granular endoplasmic reticula were declined as the phylogentical grade is going lower. 3. Tufted cells of all animal are mostly spindle or polygonal contour and contain oval nuclei which located in periphery of cytoplasm. The nuclei of rabbit, fowl, viper and frog has relatively space chromatin, but a nucleus of crussian carp contain irregularly aggregated chromatin in karyoplasm. Their cytoplasmic volume and cell organelle contents are in between those of mitral cell and granular cell. They contain moderate amount of mitochondria, granular endoplasmic reticula, a few Golgi complex, polysomes, lysosome, etc. 4. Granule of cells of all the vertebrate amimals studied exhibit similar features; cells and their dense nuclei show spherical or oval contour, and they have the thin rim of cytoplasm which contain only a few cell organelles. 5. In rabbit, the soma of mitral cells were in contact with boutons with two types of synaptic vesicles, that is, round and flat vesicles, especially flat vesicles in boutons were showing reciprocal synapses. However, in domestic fowls, vipers, frogs and crussian carps, there were found boutons showing only spherical synaptic vesicles. 6. The boutons containing round synaptic vesicles were made contact with the some of tufted cell of olfactory bulb in the rabbits, fowls, vipers and frogs, but no synaptic boutons were observed in soma of tufted cells in crussian carps. In the frogs, there were observed dendrites were contact with the soma of tufted cells. 7. In the neuropils of plexiform, granular and glomerular layers olfactory bulbs in the vertebrate, the synapses were axo-large dendrites, axo-median and small dendrites, dendrodendritic, and axo-axonal contacts. However, in the neuropil of crussian carps, synapses were observed only in glomerular layer.

• Restorative Dentistry and Endodontics
• /
• v.35 no.5
• /
• pp.353-358
• /
• 2010

Objectives: The purpose of this study was to measure the power density of light curing units transmitted through resin inlays fabricated with direct composite (Filtek Z350, Filtek Supreme XT) and indirect composite (Sinfony). Materials and Methods: A3 shade of Z350, A3B and A3E shades of Supreme XT, and A3, E3, and T1 shades of Sinfony were used to fabricate the resin inlays in 1.5 mm thickness. The power density of a halogen light curing unit (Optilux 360) and an LED light curing unit (Elipar S10) through the fabricated resin inlays was measured with a hand held dental radiometer (Cure Rite). To investigate the effect of each composite layer consisting the resin inlays on light transmission, resin specimens of each shade were fabricated in 0.5 mm thickness and power density was measured through the resin specimens. Results: The power density through the resin inlays was lowest with the Z350 A3, followed by Supreme XT A3B and A3E. The power density was highest with Sinfony A3, E3, and T1 (p < 0.05). The power density through 0.5 mm thick resin specimens was lowest with dentin shades, Sinfony A3, Z350 A3, Supreme XT A3B, followed by enamel shades, Supreme XT A3E and Sinfony E3. The power density was highest with translucent shade, Sinfony T1 (p < 0.05). Conclusions: Using indirect lab composites with dentin, enamel, and translucent shades rather than direct composites with one or two shades could be advantageous in transmitting curing lights through resin inlays.

• Journal of the Mineralogical Society of Korea
• /
• v.30 no.4
• /
• pp.149-159
• /
• 2017

We investigated the mineralogical and chemical characteristics of oyster shell as the possible substitute for the limestone used as an absorbent of $SO_2$ gas. The oyster shells from Taean and Tongyeong were used for the comparison with limestone and those from Boyreong and Yeosu were additionally investigated. XRD results show that all shells are composed of calcite with the exception of the myostracum layer attached to adductor muscle and ligament, which is composed of aragonite. The marine sediments as impurities exist on the surface of shells or as inclusions in the shells. Calcite is the main mineral composition of the shell of barnacle which is also one of the impurities. The oyster shell is composed of three main layers; prismatic, foliated, and chalk. The oyster shell from Tongyeong with the largest shell size, has the smallest thickness of prismatic and foliated layers which contain protein called conchiolin, whereas that from Taean with the smallest shell size has the largest prismatic and foliated layers. The sizes of those two layers of the shells from Boryeong and Yeosu are larger than that from Tongyeong but smaller than Taean. Those differences are supposed to be due to the different growth environments because the oysters from Tongyeong are cultured under the sea while those from Taean are in the tidal zone. The oyster shells generally show higher amount of sulfur and phosphorus than limestone, mainly due to the composition of protein. Some elements such as Mg show significant variations in different layers. As for trace elements, Li shows much higher amount in oyster shells than limestone, suggesting the influence of the composition of the sea water on the formation of the oyster shells.

• Journal of Plant Biotechnology
• /
• v.41 no.4
• /
• pp.180-193
• /
• 2014

In plants, a shoot apex has a small region known as the shoot apical meristem (SAM) having a group of dividing (initiating) cells. The SAM gives rise to all the groundabove structures of plants throughout their lifetime, and thus it plays important role in growth and development of plants. This review describes theories to explain the SAM organization and function developed over the last 250 years. Since in 1759 German botanist C. F. Wolff has described firstly the SAM, in 1858 Swiss botanist C. N${\ddot{a}}$geli proposed the apical cell theory from the observation of a large single apical cell in the SAM of seedless vascular plants: however, this view was recognized to be unsuitable to seed plants. In 1868, German botanist J. Hanstein suggested the histogen theory: this concept subdividing the SAM into dermatogen, periblem, and plerome was unable to generally apply to seed plants. In 1924, German botanist A. Schmidt proposed the tunica-corpus theory from the examination of angiosperm SAM in which two parts show different planes of cell division: this theory was proved to be not suitable to gymnosperm SAM, not have stable surface tunica layer. In 1938, American botanist A. Foster described zones in gymnosperm SAM based on the cytohistologic differentiation and thus called it a cytohistological zonation theory. With works by E. Gifford, in 1954, this zonation pattern was demonstrated to be also applicable to angiosperm SAM. As another theory, in 1952 French botanist R. Buvat proposed the m${\acute{e}}$rist${\grave{e}}$me d'attente (waiting meristem) theory: however, this concept was confuted because of its negation of function during vegetative growth phase to central initial cells. Rescent studies with Arabidopsis thaliana have found that formation and maintenance of the SAM are under the control of selected genes: SHOOTMERISTEMLESS (STM) gene forms the SAM, and WUSCHEL (WUS) and CLAVATA (CLV) genes function in maintaining the SAM; signaling between WUS and CLV genes act through a negative feedback loop.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.9
• /
• pp.228-234
• /
• 2016

The aim of this study was to develop pharmaceutical dosage forms with a bi-phasic drug using a double extrusion approach. Hot melt extrusion was performed using a co-rotating twin-screw extruder. The. 1st melt extrusion was performed using polymer with a relatively higher Tg, such as HPMC and the 2nd melt extrudate was obtained using the 1st extrudate and polymers with a lower Tg, such as HPMC-AS and PEO. In addition, the formulation with all the content in the same proportion as the double extudate was produced using single extrusion for comparison. Physical characterization was performed on the formulations employing differential scanning calorimetry (DSC). In vitro release tests were studied using a USP Type-I apparatus at $37{\pm}0.5^{\circ}C$ and 100 rpm. The similarity factor (f2) was also used to check the difference statistically. The DSC results indicated that the crystallinity of ibuprofen was changed to an amorphous state after extrusion in both double and single melt extrusion. Double melt extrudate with ibuprofen showed the desired release in acidic media (pH 1.2) in the first two hours and basic (pH 6.8) during six hours. Double melt extrudate with glimepiride showed faster release in 60 min of over 80%, whereas the single extrudate with glimepiride showed retarded release due to the interaction with HPMC. The similarity factor(f2) value was 28.5, which demonstrates that there were different drug release behavior between the double and single extrusion. Consequently, the double melt extrudated formulation was robust and gave the desired drug release pattern.