• Advances in aircraft and spacecraft science
• /
• 제7권3호
• /
• pp.187-202
• /
• 2020

The exhaust nozzle serves back pressure of Pulse detonation combustor, so combustion chamber gets sufficient pressure for propulsion. In this context recent researches are focused on influence of nozzle effect on single cycle detonation wave propagation and propulsion performance of PDE. The effects of various nozzles like convergent-divergent nozzle, convergent nozzle, divergent nozzle and without nozzle at exit section of detonation tubes were computationally investigated to seek the desired propulsion performance. Further the effect of divergent nozzle length and half angle on detonation wave structure was analyzed. The simulations have been done using Ansys 14 Fluent platform. The LES turbulence model was used to simulate the combustion wave reacting flows in combustor with standard wall function. From these numerical simulations among four acquaint nozzles the highest thrust augmentation could be attained in divergent nozzle geometry and detonation wave propagation velocity eventually reaches to 1830 m/s, which is near about C-J velocity. Smaller the divergent nozzle half angle has a significant effect on faster detonation wave propagation.

• 에너지공학
• /
• 제22권4호
• /
• pp.399-405
• /
• 2013

엔진 실린더 내부의 난류유동 특성은 내연기관의 열효율을 결정하는 매우 중요한 역할을 한다. 실린더 내 난류유동은 복잡한 3차원 유동으로 유동특성에 대한 자세한 정보는 엔진설계의 최적화를 위해 필수적이다. 균일 예혼합 압축착화(HCCI) 엔진은 가솔린과 디젤엔진 사이의 하이브리드 연소개념이다. 실린더 내 기체의 난류유동은 운동량과 열의 혼합 및 전달률을 증가시키므로 벽면에서의 열전달에 관여하여 HCCI 연소 과정에 중요한 영향을 미치게 된다. 본 연구에서는 연소실 형상에 따른 연소실 내의 기체 난류유동을 LES 모델을 사용한 전산수치해석을 통해 분석하여 HCCI 엔진 연소과정에 미치는 영향을 확인하였고 연구결과는 HCCI 엔진에서 연소실 형상에 따른 연소 특성과 엔진 성능을 개선하기 위한 기본적인 지침에 활용될 수 있다.

• 한국항공우주학회지
• /
• 제33권6호
• /
• pp.64-70
• /
• 2005

본 논문에서는 충돌형 분사기를 장착한 연료 과잉 가스발생기에서 수행한 설계점 및 탈설계점 연소시험의 전반적인 결과에 대하여 논하였다. 가스발생기는 충돌형 분사기와 추진제 공급 메니폴드로 구성된 분사기 헤드, 물냉각 채널을 가진 연소실, 혼합을 증가시키는 turbulence ring, 온도 및 압력을 측정하는 링, 그리고 노즐로 구성되었다. 여러 운영조건에서 연소시험은 성공적이었으며 가스발생기 손상은 발생하지 않았다. 체류시간 4～6msec 정도에는 출구온도변화가 거의 없었지만 압력변동에 따라 출구온도는 변하였다. 측정되는 압력, 유량 그리고 노즐목 크기로 계산한 연소효율는 출구에서 측정한 온도의 제곱근에 비례하는 관계식을 저 혼합비 가스발생기에서도 갖고 있었다. 가스발생기의 O/F 비 변화에 가장 민감하게 출구온도가 변화하였으며 이에 대한 관계식을 도출하여 향후 설계 기초 자료로 활용되게 하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1971-1972
• /
• 2008

Cardiopulmonary resuscitation(CPR) is an important clinical technique performing artificial ventilation and chest compression on a patient under emergent situation before arriving in hospital. Since the quality of CPR significantly affects the survival rate, it would be of great advantage to monitor respiration in real time during CPR. However, currently applied respiratory air flow transducers are difficult to apply with sensing elements in the middle of the flow axis. The present study developed a new turbulent air flow transducer conveniently applicable to CPR. Abrupt changes in diameter of the flow tube generated turbulence in air flow, thereby pressure difference was obtained to estimate the air flow rate, with no physical object on the flow plane. Expiration and inspiration were separated by the direction of the pressure difference, resulting in good symmetry. Pressure-flow relationship was tested on a quadratic model, which provided accurate enough estimation results. Therefore, the present turbulent air flow transducer seemed appropriate to monitor respiration during CPR.

• 전자공학회논문지SC
• /
• 제42권1호
• /
• pp.33-37
• /
• 2005

마이크로믹서는 Bio-MEMS 혹은 μ-TAS 분야에서 중요한 역할을 수행한다. 혼합은 두 유체의 난류 상태와 상호확산에 의해 발생된다. 마이크로채널 내에서는 레이놀즈수가 작기 때문에 (Re << 2000) 난류가 발생되기 어려우므로 주로 상호확산에 의해서만 혼합된다. 따라서 두 유체가 적정하게 혼합되기 위해서는 긴 채널이 요구된다. 본 논문에서는 혼합에 소요되는 길이를 줄이기 위해서 PMN-PT에 의해 발생된 초음파에 의해 혼합되는 새로운 믹서를 제안하였다. 챔버 내에 발생된 초음파는 두 유체에 의해 생성된 경계면과 수직한 방향으로 방사된다. 사용된 두 유체는 상하방향으로 경계층을 이룬다. 혼합 상태는 NaOH와 페놀프탈렌의 반응에 따른 색상 변화론 관찰하여 측정하였다.

• 대한기계학회논문집B
• /
• 제34권10호
• /
• pp.925-931
• /
• 2010

본 논문은 공동 주위 난류유동특성을 LES 기법으로 수치해석을 수행하여 알아보았다. 본 연구에 적용된 레이놀즈수는 공동 깊이만큼의 높이 h 에서의 유속을 기준으로 $1.0{\times}10^5$ 이며 3 차원 공동에서의 유동특성을 알아보았다. 적절한 비압축성 Filtered Navier-Stokes 방정식을 적용하기 위해, 계산격자를 공동 표면 근처에는 조밀하게 멀어질수록 성기게 생성하였으며, 이는 계산시간을 단축시키며 빠른 수렴을 도와준다. 또한, Boussinesq 가설을 subgrid-scale 난류모델에 적용하였고, Subgrid-scale 난류점성을 얻기 위해 smagorinsky-Lilly SGS 모델을 적용하였으며, 그 때의 CFL 수는 1.0 이다. 또한, 본 논문은 서로 다른 4 가지 형상의 공동의 및 입구조건의 변화에 따른 유동 특성도 함께 연구되었다.

• 한국자동차공학회논문집
• /
• 제12권2호
• /
• pp.24-31
• /
• 2004

A cylindrical constant volume combustion bomb is used to investigate the combustion characteristics and to analyzer the heat quantity of inhomogeneous charge methane-air mixture. To analyze the heat quantity, some definitions including the CHR ratio, the UHC ratio and the HL ratio are needed and are calculated. It is shown that the effect of stratification is not significant in case of the overall excess air ratio of 1.1, mainly due to the higher heat loss and lower thermal efficiency compared to those of homogeneous condition. In the case of the overall excess air ratio of 1.4, as the initial charge pressure decreases, the CHR ratio has been decreased while the HL ratio has been increased, Generally, as the initial charge pressure increases, the amount of injection mixture has been decreased and has resulted in lower mean velocity and turbulence intensity for injection mixture. Also, the injected mixture is too rich to result in mixing deficiency in combustion chamber. From these results, it could be possible to acquire the improvement of thermal efficiency and the reduction of heat loss simultaneously through the 2-stage injection in CNG direct injection engine.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.29-33
• /
• 2004

This paper presents ESPI system for the measurement of thermal expansion coefficient of STS430 up to 1,000$^{\circ}C$. Existing methods, strain gauge and moire have the limitation of contact to object and do not supply the coefficient up to 800$^{\circ}C$. There needs to measure the data up to 800$^{\circ}C$, because heat resistant materials have high melting temperature up to 1,000$^{\circ}C$. In previous studies related to thermal strain analysis, the quantitative results are not reported by ESPI at high temperature, yet. In-plane ESPI and vacuum chamber for the reduction of air turbulence and oxidation are designed for the measurement of the coefficient up to 1,000$^{\circ}C$and speckle correlation fringe pattern images are processed by commercial image filtering tool-smoothing, thinning and enhancement- to obtain quantitative results, which is compared with references data. The comparison shows two data are agreed within 4.1％ blow 600$^{\circ}C$ however, there is some difference up to 600$^{\circ}C$. Also, the incremental ratio of the coefficient is changed up to 800$^{\circ}C$. The reason is the phase transformation of STS430 probably begins at 800$^{\circ}C$.

• 한국안전학회지
• /
• 제21권3호
• /
• pp.38-44
• /
• 2006

The majority of both small and large-scale experiments on gas explosion have been carried out in the explosion instruments with cylindrical tubes of a high length/diameter ratio and vessels of a high height/length ratio, focusing on investigating the interaction between propagating flame and obstacles inside the tubes or vessels. The results revealed that there is a strong interaction between the propagating flame and turbulence formed after the flame passes the obstacle. However this paper focuses on analyzing the pressure impact or profile outside the vent in vented gas explosion in a partially confined chamber by performing gas explosion experiments in a reduced-scale experimental assembly properly constructed. This study has considered eight different cases in gas explosion based on variation of three kinds of parameters such as height of vessel, shape of the vent and vent size, and reveals that the large vessel with big size circle vent is more danger to the target than others because the overpressure is spread out faraway horizontally and vertically.

• 동력기계공학회지
• /
• 제21권6호
• /
• pp.5-12
• /
• 2017

The steady-state, incompressible and three-dimensional numerical analysis was carried out to investigate the internal flow fields characteristics according to wind tunnel contraction type. The turbulence model used in this study is a realizable $k-{\varepsilon}$ modified from the standard $k-{\varepsilon}$ model. As a results, the distribution of the axial mean velocity components along the central axis of the flow model is very similar to the ASME and BE types, and the cubic and cosine types. When the flow passes through the interior space of the analytical models, the flow resistance at the inlet of the plenum chamber is the largest at BS type contraction, but the smallest at cubic type contraction. The boundary layer thickness is the smallest in the cosine type contraction as the axial distance increases. The maximum turbulent kinetic energy in the test section is the smallest in the order of the contraction of cubic type and cosine type. Comprehensively, cubic type contraction is the best choice for wind tunnel performance, and cosine type contraction can be the next best solution.