• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.5A
• /
• pp.513-518
• /
• 2010

Improvement of phase noise characteristics in a different approach of HEMT VCO (Voltage Controlled Oscillator) with coupled microstrip lines to tune the oscillating frequency is investigated. Two HEMT VCOs of 9.8GHz are manufactured in the same configuration except for the frequency tuning circuit in order to empirically demonstrate the phase noise reduction. Experimental result shows that phase noise reduction can be enhanced 8dBc/Hz at 100KHz offset frequency from carrier by frequency tuning circuit with coupled microstrip lines over the conventional VCO.

• Journal of IKEEE
• /
• v.16 no.2
• /
• pp.121-126
• /
• 2012

In this paper, a push-push VCDRO (Voltage Controlled Dielectric Resonator Oscillator) with a modified frequency tuning structure is investigated. The push-push VCDRO designed at 16GHz is manufactured using a LTCC (Low Temperature Co-fired Ceramic) technology to reduce the circuit size. The frequency tuning structure is embedded in intermediate layer of A6 substrate by an advantage of LTCC process. Experimental results show that the fundamental frequency suppression is above 30dBc, the frequency tuning range is 0.43MHz over control voltage of 0 to 12V, and phase noise of push-push VCDRO presents a good performance of -103dBc/Hz at 100KHz offset frequency from carrier.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.1
• /
• pp.102-106
• /
• 2009

This paper presents the design and optimization of output matching network according to envelope for class F power amplifier(PA) which is to apply to envelope elimination and restoration(EER) transmitter. In this paper, to increase the PAE of class F power amplifier which applies to EER transmitter, the varactor diode has been used on output matching network. As envelope changes, it optimizes constitution of harmonic trap that is short circuit in 2nd-harmonic and is open circuit in 3rd-harmonic. When drain voltage changes from 25 V to 30 V, some percentage is improved in the PAE.put the abstract of paper here.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.3
• /
• pp.17-27
• /
• 1996

More fuzzy hardware are expected to be utilized in the future to construct fuzzy logic controllers (FLCs). It is hard to find an existing fuzzy hardware which is adopting advanced functions such as self-tuning algorithm in addition to the conventional inference calculation. That is mainly because conventional self-tuning algorithms designed to implement with some hardware circuits is required for fuzzy hardwares to have self-tuning capability. As a first step toward the feature, a novel self-tuning algorithm is proposed in this paper. Based on the search method, the main idea of the proposed algorithm is to detemine valid ranges of input variables of an FLC in order to maximize performance indices fo the control system. The performance indices are so ismple as to be realized by hardware circuit. in dadditon to the conventional scaling-factor adjustment, the algorithm adjusts offset values as well, which, in effect, modifies fuzzy rules of the FLC. To justify the performance of the proposed algorithm, a simulation study is executed.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.118-121
• /
• 2003

A new approach, using MEMS, for improving the performance of high efficiency amplifiers is proposed in this paper. The MEMS tuning element is described as a variable-length shorted CPW stub. Class-E amplifiers can be optimally tuned by these MEMS tuning elements because their operation varies with the impedance of the output tuning circuit. A MEMS tuning element was simulated using full-wave EM simulators to obtain its S-parameters. A Class-E amplifier with the MEMS was designed at 8GHz. The non-linear operation of this amplifier was simulated to explore the effect of the MEMS tuning. Comparing the initially designed amplifier without MEMS, the Power Added Efficiency (PAE) of the amplifier with MEMS is improved from 46.3% to 66.9%. For the amplifier with MEMS, the nonlinear simulation results are PAE = 66.90%, $\eta$(drain efficiency) = 75.89%, and $P_{out}$ = 23.37 dBm at 8 GHz. In this paper, the concept of the MEMS tuning element is successfully applied to the Class E amplifier designed with transmission lines.

• Proceedings of the KIEE Conference
• /
• 2002.07a
• /
• pp.544-547
• /
• 2002

In a high power laboratory, artificial lines are used for SLF tests of circuit breakers. The line side PTRV is affected by the stray capacitances of testing and measuring equipment as well as the circuit parameters of artificial lines. The changing pattern of PTRV was examined, and the circuit parameters of artificial line for some examples were compensated using the changing pattern to satisfy test conditions specified.

• ETRI Journal
• /
• v.27 no.1
• /
• pp.75-80
• /
• 2005

This paper addresses a fully-integrated low phase noise X-band oscillator fabricated using a carbon-doped InGaP heterojunction bipolar transistor (HBT) GaAs process with a cutoff frequency of 53.2 GHz and maximum oscillation frequency of 70 GHz. The oscillator circuit consists of a negative resistance generating circuit with a base inductor, a resonating emitter circuit with a microstrip line, and a buffering resistive collector circuit with a tuning diode. The oscillator exhibits 4.33 dBm output power and achieves -127.8 dBc/Hz phase noise at 100 kHz away from a 10.39 GHz oscillating frequency, which benchmarks the lowest reported phase noise achieved for a monolithic X-band oscillator. The oscillator draws a 36 mA current from a 6.19 V supply with 47.1 MHz of frequency tuning range using a 4 V change. It occupies a $0.8mm{\times}0.8mm$ die area.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.1
• /
• pp.177-182
• /
• 2010

The forward convener is one of power supplies used widely. This paper presents parameter tuning methods to obtain optimal circuit element values for the forward converter to minimize the output voltage variation under various load changing environments. The conventional method using the concept of the phase margin is extended to have optimal phase margin that gives slightly improved performance in the output voltage response. For this, the phase margin becomes the tuning parameter and is optimized with the genetic algorithm. Next, the circuit element values are directly chosen as the tuning parameters and also optimized using the genetic algorithm to have very improved performance in the output voltage control of the forward converter.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.13 no.3
• /
• pp.143-149
• /
• 2018

It has become ever harder to design reliable circuits with each nanometer technology node; under normal operation conditions, a transistor device can be affected by various aging effects resulting in performance degradation and eventually design failure. The reliability (aging) effect has traditionally been the area of process engineers. However, in the future, even the smallest of variations can slow down a transistor's switching speed, and an aging device may not perform adequately at a very low voltage. Therefore, circuit designers need to consider these reliability effects in the early stages of design to make sure there are enough margins for circuits to function correctly over their entire lifetime. However, such an approach excessively increases the size and power dissipation of a system. As the impact of reliability, new techniques in designing aging-resilient circuits are necessary to reduce the impact of the aging stresses on performance, power, and yield or to predict the failure of a system. Therefore, in this paper, a novel low power on-chip self-tuning circuit considering the aging effects has been proposed.

• The Journal of the Convergence on Culture Technology
• /
• v.4 no.4
• /
• pp.419-427
• /
• 2018

This paper designs and develops auto-tuning temperature controller with multi-channel, which controller with multi-channel could control a number of control system simultaneously. This controller has multi-channel input and output. And a number of control algorithms run in this controller simultaneously and independently. Firstly we present design method of controller with multi-channel. Secondly we design electrical circuit of sensor input, controller output and power control for temperature control board. And finally we design data protocol for serial communication to monitor control state and present verification of temperature controller with muiti-channel through field experiment.